Aventura CAM-AHY-2B-212V-IR Quick Start Manuals

Brand: Aventura

Model: CAM-AHY-2B-212V-IR

Type: Quick Start Manuals

WWW.AVENTURACCTV.COM

DOCUMENT V1.2

Quick Start Guide

Related Series Models:

CAM-AHY-2B-212V-IR, CAM-AHY-5B-212V-IR

The product comes with the following components:

1. Camera Device.

2. Attachment screws and anchor pack.

3. L-Key for adjustment of camera bracket.

4. Software CD

Be sure no parts are missing from the product before

installation.

Information in this document is subject to change without notice. As our

products are subject to continuous improvement, Aventura

Technologies reserves the right to modify product design, specifications

without notice and without incurring any obligation. E&OE

AVENTURA TECHNOLOGIES, INC.

HEADQUARTERS

48 Mall Drive, Commack, New York 11725 U.S.A.

Tel: +1.631.300.4000 Fax: +1.631.434.7000

INSTALLATION

1. Below is an overview of the parts of the

camera, showing how the completed

product would look.

Visor adjustment

Attachment Location

Focus-zoom adjustment*

*Some models like shown have auto-focus zoom and offer

no adjustment access. Access panel would be located at

the bottom of the camera to provide access to the manual

focus-zoom levers.

Use the bracket base for locating drill positions

and attach the camera using the supplied anchors/wall

plugs and attachment screws.

Note: You need be sure of the waterproof surround of the camera

& cables if externally fitted, consult professional if in doubt some

buildings it is possible that thermal dampness or moisture can get

into stud walls. Always be safe with cables and connections.

2. All adjust to position and angle of the bullet

using the adjustment hex bolts located on the

rear base of the camera. Use the L-Key turn

anti-clockwise to loosen. The adjustment has

teeth inside to lock into a position to prevent

drifting.

Angle Adjustment Nut

Twist position adjustment

5. Focus and zoom for camera image and field of

view require the external adjustments, with the

device being powered on is the only way to be

sure to obtain the correct position and desired

angle. Autofocus zoom models do not require

any adjustment as this is achieved

automatically.

NOTE: You may opt to not tighten completely until focus and

zoom adjustments have been completed. Once properly

focused and zoomed, tightening these nuts prevent the

camera view from drifting.

6. CAD Dimensions Inch (mm)

CONNECTION & OSD

The camera has the following termination cables.

1. BNC Interface: Connect to appropriately qualified

cable and attach to the DVR / XVR recording unit.

NOTE: RG59 Cable should be of high quality and using pure

copper inner core, low-cost cables using copper over steel may

give unexpected results for video signal and should not be used.

2 Power Interface: Standard CCTV 12V power

connection, connect to a qualified regulated

supply.

DC12V (600mA): 12V DC power input terminal. Make sure

to follow correct polarity with the + as the inner pin of the

supply

Some models may include an OSD built into the cable,

whilst the device supports OTC (Over the Cable) control,

the on cable is here for when DVRs may not support the

OSD function from the recording device.

Control of OSD is simple with the little four direction

control, and push down to activate. We referred the push

as entering or OK in the rest of this guide.

OSD MENU USAGE

The camera comes with a typical set of parameters for

image output used by the camera. Using the OSD, you are

able to affect the camera performance to suit the

installation requirement of the device.

Note: You can also use the OSD from your DVR/XVR device if

the control over cable method is supported, check the manual for

this device.

Press

○

E to enter the OSD menu you are presented with

the following top-level Menu.

You navigate around using the

○

L Left,

○

R Right,

○

Up,

○

D Down positions using the control button. To

change or activate a setting press down

○

E entering. This

will activate or allow change the current position value.

The currently selected position is indicated by the two circle

as highlighted in red.

Where there is a ←ˡ on the right side of selection, this

indicates an option or will change to another menu level.

Note: From top-level menus you can Exit, to retain changes for

when the camera is restarted, you must activate the Save option.

BACK Goes back to previous menu options

NEXT Goes forward to next menu options

SAVE All modified settings you have changed will be

written to the camera memory, so when it’s reset or

restarted the changes made are kept.

EXIT Closes the OSD menu from the system, retaining

current changes, but only until the next power cycle of the

camera.

6 Inch ( 152 mm )

2Inch ( 53mm )

○

BNC RG59

12V DC 5.5x2.1mm

WWW.AVENTURACCTV.COM

DOCUMENT V1.2

MAIN MENU is the top level main menu, select option

up and down control, will either select an option or

change the displayed information option setting.

When you have an  arrow will let you select a sub-

menu option.

EXPOSURE Control the camera image settings.

SHUTTER: {AUTO {SLOWSHUTTER: Auto,

x1,x2,x3,x4,x5,x6,x7,x8,x9} MANUAL {SHUTTER SPEED:

50.100,250,500,2000,5000,10000,100000}}

AGC: Auto gain control adjustment.

BRIGHTNESS: Picture brightness level.

D-WDR: Digital WDR

{ON/OFF}

RETURN: Returns to the top level menu.

All numbered selection allows a left-right adjustment

value to be set.

SAVE&END You need to save settings

modified on the menu to be stored even after a power

cycle of the device.

BACKLIGHT Top Level Menu {OFF/ON}

WHITE BAL White Balance {ATW Auto}

D&N EXT IR LED / IR Cut filter change over status.

N Day to Night seconds duration.

D Night to Day seconds duration.

NOTE: Ext uses an external photosensor to detect light levels.

NR Top Level Menu Noise Reduction

2DNR Low Medium High noise reduction level.

NOTE: Noise reduction will reduce hard edges, but will also

soften the image edges. The incorrect setting may affect recorded

image storage size due to more complex image compression.

SPECIAL Top Level Settings

G AE

MIRROR {Off, Horizontal, Vertical, Both}

NOTE: Mirror provide a means when a camera needs to be

installed upside fitted, or when need to see image reversed.

DPC Dead Pixel Correction

NOTE: Dead pixel function is advanced to allow for white dots

which can appear on sensors. Each option in the DPC menu will

allow correcting each type, White / Black.

LANGUAGE: Selection for OSD Language.

ADJUST Top Level Menu {OFF/ON}

SHARPNESS {Level and Start – End gain control}

MONITOR Gamma, Blue Gain, and Red Gain.

LSC Lens Shadow Correction

OUTPUT MODE

FORMAT: AHD, CVI, TVI, CVBS.

VIDEO OUTPUT: PAL / NTSC setting

NRT: Near Real Time

{ON/OFF}

RETURN: Returns to top level menu.

NOTE: NRT is designed for recorders which don’t display images

in real-time. Normally this setting would not need to be enabled.

Aventura CAM-AHY-2B-212V-IR Quick Start Manuals

Aventura CAM-AHY-2B-212V-IR Quick Start Manuals

Aventura CAM-AHY-2B-212V-IR Quick Start Manuals

Related papers

Other documents