Dometic 3109687.008_W-O Decal and 3109749.006_ Installation guide

Dometic
Brand
Dometic
Model
3109687.008_W-O Decal and 3109749.006_
Type
Installation guide
3109687.008 (W/O Decal) & 3109749.006
(With Decal) Automatic Control Box Kit
Wiring Using AMP UNIVERSAL MATE-N-
LOK R SOFT SHELL CONNECTOR
REVISION
Form No. 3109695.019 12/00
(Replaces 3109695.001)
©2000 The Dometic Corporation
LaGrange, IN 46761
FIG. 1
AMP 15 Pin MATE-N-LOK parts required by Installer:
(1) 770023-1 Housing
(1) 794281-1 Interface Seal
(1) 794282-1 Wire Seal
(2) 770246-3 Pin (12-10 gauge)
(11) 770248-1 Pin (20-14 gauge)
AMP 2 PIn MATE-N-LOK parts required by Installer:
(1) 1-480698-0 Housing
(2) 350547-1 Pin (20-14 gauge)
(1) 794270-1 Wire Seal
(1) 794269-1 Interface Seal
Pin 1 12+VDC Red 12 Gauge
Pin 2 12- VDC Black 12 Gauge
Pin 3 Ignition Isolator Pink 16 Gauge
Pin 4 Oasis Remote Switch Green/White 16 Gauge
Pin 5 OneStep Remote Switch Green 16 Gauge
Pin 6 Blank
Pin 7 Oasis Motor (-12VDC) Blue 16 Gauge
Pin 8 OneStep Motor (-12VDC) Black 16 Gauge
Pin 9 Oasis Remote Switch Yellow/White 16 Gauge
Pin 10 OneStep Remote Switch Yellow 16 Gauge
Pin 11 Blank
Pin 12 Oasis Motor (+12VDC) Red 16 Gauge
Pin 13 OneStep Motor (+12VDC) Red 16 Gauge
Pin 14 Oasis Remote Switch Brown/White 16 Gauge
Pin 15 OneStep Remote Switch Brown 16 Gauge
Location Pin Functions Wire Color Wire Size
AMP UNIVERSAL MATE-N-LOK
Soft Shell Connector
R
Auxilary
Power (For
OneStep Only)
Black
Red
13
10
7
4
1
14
8
5
2
15
12
3
11
9
6
Winnebago Wiring Oasis
FRTA
12 Red 16 Gauge
7 Blue 16 Gauge
Red 12VDC + 12 Gauge
Black 12VDC - 12 Gauge
1
2
OneStep Main
Arm- Awning
Right Side
13 Red 16 Gauge
8 Black 16 Gauge
AMP 2-Pin
Connector
1
2
EXTEND 4 Green/White 16 Gauge
NEUTRAL 14 Brown/White 16 Gauge
RETRACT 9 Yellow/White 16 Gauge
Oasis
Remote
Switch
EXTEND 5 Green 16 Gauge
NEUTRAL 15 Brown 16 Gauge
RETRACT 10 Yellow 16 Gauge
OneStep
Remote
Switch
3 Pink 16 Gauge
Ignition
Isolator
13
10
7
4
1
14
8
5
2
15
12
3
11
9
6
1
2
67-7/8
.5
67-1/8
Hole location for motor
wire entry into coach
FIG. 2
When routing harness, take pre-caution against wires
rubbing on sharp edges and use a grommet when going
through walls. Harness should be routed so that when
bottom bracket and the extension are installed (OneStep)
they will cover hole where wire goes through wall. Seal any
holes with clear silicon sealant. See FIG. 2.
C. Remote Switch (Supplier Installed)
1. Install the remote switch(s) at a convenient loca-
tion such as the door area.
2. The remote switch(s) should not be in direct
exposure to weather or extreme temperatures.
3. Mount switch per manufactures instructions.
4. Connect the remote switch to the control box
by routing three (3) 16 gauge wires (installer
supplied) from the remote switch(s) to the 15
pin MATE-N-LOK connector. See FIG. 1 for pin
locations. These wires should be brown, yellow
and green for OneStep and brown/white, yellow/
white and green/white for Oasis. Install 1/4" insu-
lated terminals on the remote switch end of wires.
Connect the wires to the remote switch as shown
in FIG. 1.
2. Low Voltage Connection
A. Run two (2) 12 gauge wires from the 12VDC power
supply source to the 15 pin MATE-N-LOK connector.
See FIG. 1 for pin locations. It is recommended that
these wires be (Red+ and Black -). This should be on
a separate 15 amp circuit.
B. The additional 2 wire pigtail w/protective cap is for
OneStep auxiliary power use only . No connection is
necessary for regular use.
3. Auto Lock Connection
A. Run a 16 gauge wire (installer supplied) from the
Ignition Isolator (+12 VDC) of vehicle to the 15 pin
MATE-N-LOK connector. See FIG. 1 for pin location.
1. Control Box and Remote Switch Installation
A. Control Box
1. First, decide on a location for the control box.
Recommended locations for the control box are
compartments outside the living quarters such as
one of the basement storage compartments. The
control box must be installed at a location where
it will not be directly exposed to weather or
extreme temperatures.
2. Mount the control box using four (4) #6 x 1/2"
screws.
B. Connect Control Box to Awning
1. Route two (2) 16 gauge wires (installer supplied)
from the bottom of right side (motorized) arm
assembly (OneStep) or FRTA assembly (Oasis)
to the 15 pin MATE-N-LOK connector. Use the
following 2 Pin AMP MATE-N-LOK parts to con-
nect awning connector to wires. See FIG. 1
for pin locations.
(1) 1-480698-0 Housing
(2) 350547-1 Pin (20-14) gauge)
(1) 794270-1 Wire Seal
(1) 794269-1 Interface Seal
Important: When installing 760111X.400 hardware
make sure channel is in proper position before drilling
the hole in side wall for wires. See FIG. 2.
  • Page 1 1
  • Page 2 2

Dometic 3109687.008_W-O Decal and 3109749.006_ Installation guide

Dometic
Brand
Dometic
Model
3109687.008_W-O Decal and 3109749.006_
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents