Allen-Bradley 1336 FORCE User manual

Brand: Allen-Bradley

Model: 1336 FORCE

Type: User manual

This manual is also suitable for

1336 PLUS II

Allen-Bradley 1336 FORCE: Control your motor with precision and efficiency. Designed for demanding applications, it offers advanced features for customizable performance. From simple speed control to complex motion applications, the 1336 FORCE provides reliable operation and connectivity options for seamless integration into your system.

Instructions

This publication will guide you through installation of an IP 20

(NEMA Type 1) Enclosure Kit (1336S/F/T-AAx) or EMC Enclosure

Kit (1336S/F/T-AEx). Refer to the appropriate drive User Manual for

further information.

Enclosure Installation

ATTENTION:ThisdrivecontainsESD(Electrostatic Dis-

charge) sensitive parts and assemblies. Static control pre-

cautions are required when installing, testing, servicing or

repairing this assembly. Component damage may result if

ESD control procedures are not followed. If you are not

familiar with static control procedures, reference A-B pub-

lication 8000-4.5.2, “Guarding Against Electrostatic Dam-

age” or any other applicable ESD protection handbook.

ATTENTION: To avoid a shock hazard, assure that all

powertothedrivehasbeenremovedbeforeproceedingwith

thefollowing procedure. In addition, verifythat the DC bus

hasdischargedbymeasuring across the “+DC”and “–DC”

terminals of TB1 with a voltmeter. The voltage should be

0.0VDC.

ATTENTION:When adrivemounted HIMisnot supplied

on enclosed IP 20 (NEMA Type 1) drives, the blank cover

plate (option HAB/HASB) must be installed to close the

openinginthe frontcoveroftheenclosure.Failuretoinstall

the blank cover plate allows access to electrically live parts

which may result in personal injury and/or equipment dam-

age.

When a drive mounted HIM is supplied with enclosed IP

20 (NEMA Type 1) drives, but has been removed from its

mountingcradle forremote operation,the blankcoverplate

must be installed in place of the HIM.

1336 PLUS, 1336 PLUS II & 1336 FORCE™

NEMA Type 1 Enclosure Kit

1336S/F/T-AAx and 1336S/F/T-AEx

2 1336 PLUS, 1336 PLUS II & 1336 FORCE™ NEMA Type 1 Enclosure Kit

Installation

Access to the top, bottom and sides of the drive chassis is required to

assemble the kit. If the open chassis drive is already installed, remove

and lock-out all power to the drive, then label and disconnect all

wiring. External wiring will have to be rerouted through enclosure

knockouts once the kit has been installed.

Figure 1

Enclosure Kits – 1336S/F-AA2 and -AA3

1. Mount the top, bottom and side plates to the chassis using the

supplied screws. Tighten all screws to 1.7 N-m (15 lb.-in.).

2. Install the front cover by sliding it up, then down to engage the

slots into the angled tabs. Swing the cover bottom “in” and secure

it with the captive screw. Tighten to 0.7 N-m (6 lb.-in.).

Figure 2

EMC Enclosure Kits – 1336S/F-AE2 and -AE3

1. Mount the bottom plate to the chassis using the supplied screws.

2. Slide enclosure assembly over the chassis as shown.

3. Fasten the assembly to the chassis using the supplied screws.

Tighten all screws to 1.7 N-m (15 lb.-in.).

Figure 3

Enclosure Kits – 1336S/F/T-AA4 and -AA5

1. Slide the side plates over the chassis tabs as shown.

2. Attach the top and bottom plates to the side plates by sliding the

tabs into the corresponding slots. Fasten the assembly to the

chassis using the supplied screws. Tighten all screws to 1.5 N-m

(13 lb.-in.).

3. Install the front cover by sliding it up, then down to engage the

slots into the angled tabs. Swing the cover bottom “in” and secure

it with the captive screw. Tighten to 0.7 N-m (6 lb.-in.).

Figure 4

EMC Enclosure Kits – 1336S/F/T-AE4 and -AE5

1. Mount the bottom plate to the chassis using the supplied screws.

2. 1336

PLUS II drives using the AE4 Enclosure Kit require

replacement of a ribbon cable. Remove the ribbon cable between

the Main Control Board and Gate Drive Board (see Figure 4).

Replace this cable with the new supplied cable (with ferrite

block). Position the cable/block as needed to prevent obstruction

with the enclosure being installed.

3. Slide enclosure assembly over chassis as shown.

4. Fasten the assembly to the chassis using the supplied screws.

Tighten all screws to 1.5 N-m (13 lb.-in.).

1336 PLUS, 1336 PLUS II & 1336 FORCE™ NEMA Type 1 Enclosure Kit 3

Replace Ribbon Cable

(1336F-AE4 Only)

Figure 1

1336S/F-AA2 & AA3 Enclosure Kits

Figure 2

1336S/F-AE2 & AE3 EMC Enclosure Kits

Figure 3

1336S/F/T-AA4 & AA5 Enclosure Kits

Figure 4

1336S/F/T-AE4 & -AE5 EMC Enclosure Kits

4 1336 PLUS, 1336 PLUS II & 1336 FORCE™ NEMA Type 1 Enclosure Kit

Door Grounding Jumper

Jumper must be Installed inside

Enclosure between Enclosure Door

(Grounding Stud) and Chassis

Grounding Stud.

Figure 5

Enclosure Kits – 1336S/F/T-AA6 and -AA7

EMC Enclosure Kits – 1336S/F/T-AE6 and -AE7

For CE conformance, the EMI gasket (pre-installed) and jumper (see

below) supplied with the 1336S/F/T-AE6 & AE7 must be in place.

1. Slide the side plates over the chassis tabs as shown.

2. Attach the top and bottom plates to the side plates by

sliding the tabs into the corresponding slots. Fasten the

assembly to the chassis using the supplied screws. Tighten

all screws to 2.8 N-m (25 lb.-in.).

3. Install the door on the side plate hinge pins.

4. For EMC Kits - locate the supplied jumper wire and fasten

one end to the chassis ground stud. The other end must be

fastened to the stud located in the lower corner of the door.

Rockwell Automation helps its customers receive a superior return on their investment by bringing

together leading brands in industrial automation, creating a broad spectrum of easy-to-integrate

products. These are supported by local technical resources available worldwide, a global network

of system solutions providers, and the advanced technology resources of Rockwell.

Worldwide representation.

Argentina • Australia • Austria • Bahrain • Belgium • Bolivia • Brazil • Bulgaria • Canada • Chile • China, People’s Republic of • Colombia • Costa Rica • Croatia • Cyprus

Czech Republic • Denmark • Dominican Republic • Ecuador • Egypt • El Salvador • Finland • France • Germany • Ghana • Greece • Guatemala • Honduras • Hong Kong

Hungary • Iceland • India • Indonesia • Iran • Ireland • Israel • Italy • Jamaica • Japan • Jordan • Korea • Kuwait • Lebanon • Macau • Malaysia • Malta • Mexico

Morocco • The Netherlands • New Zealand • Nigeria • Norway • Oman • Pakistan • Panama • Peru • Philippines • Poland • Portugal • Puerto Rico • Qatar • Romania • Russia

Saudi Arabia • Singapore • Slovakia • Slovenia • South Africa, Republic of • Spain • Sweden • Switzerland • Taiwan • Thailand • Trinidad • Tunisia • Turkey • United Arab Emirates

United Kingdom • United States • Uruguay • Venezuela

Rockwell Automation Headquarters, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414 382-2000, Fax: (1) 414 382-4444

Publication 1336 PLUS-5.6 – July, 1998 P/N 74001-008-01 (02)

Figure 5

1336S/F/T-AA6 & -AA7 Enclosure Kits

1336S/F/T-AE6 & -AE7 EMC Enclosure Kits