Keystone KoolSpot Silver Series Installation guide

Brand: Keystone

Model: KoolSpot Silver Series

Type: Installation guide

KoolSpot Silver Series Solar Shades

Description Part Number Qty Included

Clutch Bracket CB8 1

Stationary Bracket SB8 1

Plastic Bracket Covers PBC8 2

Top Tube Clutch Plug TTCP8 1

Top Tube Stationary Plug TTSP8 1

Bottom Rail BR8 1

Bottom Rail Caps BRC8 2

Chain CH8 1

Shade SE8 1

Screws SCR8 5

Tension Device TDE8 1

Tools required: phillips screwdriver, leveling device (lazer level, standard level, etc.), and

power drill (if pre-drilling the holes).

INSTALLATION INSTRUCTIONS

Warranty and maintenance

To clean your KoolSpot shade simply rinse with water and scrub with any non-abrasive

cleaner (using bleach or other abrasive cleaners will void your warranty). Roll the shade

down to air dry.

Your KoolSpot Solar Shade fabric has a warranty of three (3) years.

Step 5: Install tension device

The Tension Device keeps the chain secure and

reduces the risk of strangulation.

Install the Tension Device in a location that

keeps the chain taught (see Fig. K).

Place the chain in the Tension Device, then

snap it closed. Attach the Tension Device to the

wall.

303.652.6164 (p)

www.KeystoneFabrics.com

Figure K

Congratulations on the purchase of your KoolSpot Solar Shade. Please read these instructions

carefully prior to installing your shade. Please call if you have any questions regarding

installation or if you are missing any parts.

Adjusting chain tension

Figure L

If the chain tension is

too tight or too loose

when you raise or

lower your shade, the

tension of your chain

can be adjusted.

Simply remove

the Plastic Bracket

Cover from the Clutch

Bracket and loosen the

screws to loosen chain

tension. Tighten

screws to tighten chain

tension (see Fig. L).

Clutch Bracket

(CB8)

Stationary Bracket

(SB8)

Top Tube Clutch Plug

(TTCP8)

Figure A

Bottom Rail

(BR8)

Bottom Rail Caps

(BRC8)

Chain

(CN8)

Shade

(SE)

Plastic Bracket Cover

(PBC8)

Plastic Bracket Cover

(PBC8)

12/07

Top Tube Stationary Plug

(TTSP8)

Tension Device

(TD8)

Loosen all screws

Replace the Plastic Bracket Cover.

Step 1: Determine type of installation

Be sure to mount the brackets to a wood stud. If a wood stud cannot be located, an anchor

must be used (see your local hardware store for assistance).

Make sure your brackets are secure before proceeding to Step 3.

Step 3: Install brackets

Step 2: Mark holes for installation

Before you can hang your solar shade, it will help to mark the holes where you will put

your screws. Figure G will help you determine where your holes should be located.

Shade size Screw to screw

measurement

Total width

(installed)

Approximate

weight

48’’ 48’’ 49 9/16” 3.1 lbs

72’’ 72’’ 73 9/16’’ 4.3 lbs

96’’ 96’’ 97 9/16’’ 5.6 lbs

120’’ 120’’ 121 9/16’’ 6.8 lbs

Secure the Clutch Bracket and Stationary

Bracket with the provided wood screws

(see Fig. H).

Do not tighten screws completely yet.

1. First, insert the Top Tube

Clutch Plug into the Clutch

Bracket.

2. Second, slide the Top Tube

Stationary Plug into the

Stationary Clutch Bracket.

Close the latch on the

Stationary Plug (see Fig. I).

Adjust the brackets snugly to

the solar shade so the solar

shade is secure (Fig. J).

Tighten screws.

WALL MOUNT

There are two (2) ways to install your solar shade (see Fig. B and C). Your solar shade

comes ready for a wall installation (Fig. B). If you prefer a wall installation (Fig. B), you

are ready to proceed to Step 2.

If you want to change your solar shade so it hangs from the top/ceiling (ceiling mount, see

Fig. C), you will need to make a change before proceeding to Step 2. Please see below if

you want to change to a Ceiling Mount.

CEILING MOUNT

Figure B

Figure C

CHANGING TO CEILING MOUNT

To change to a ceiling mount, you

will need to remove the Plastic

Bracket Covers and remove all

screws (see Fig. D) from the Clutch

Bracket and Stationary Bracket.

Figure D

Step 4: Install solar shade

Figure H

Figure I

Figure G

Figure J

Figure E

Figure F

After removing the screws, change

the Clutch Bracket so it matches

Figure F, and change the

Stationary Bracket so it matches

Figure E.

Replace the screws and Plastic

Bracket Covers when nished.

Keystone KoolSpot Silver Series Installation guide

Keystone KoolSpot Silver Series Installation guide

Keystone KoolSpot Silver Series Installation guide

Related papers

Other documents