User guide
XDVA2508 - XDVA2516
FA00305-EN
Page 2 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
INSTALLING THE HARD DRIVE
The manufacturer reccomends using a SATA hard drive. Before installing, cut o the main power supply.
Fit the hard drive to the lower part of the PC's shell, only after connecting the power supply and data cables.
Description of parts
Back panel XDVA2508
Back panel XDVA2516
1. Audio channels inputs
2. 12 V DC Power supply
3. Relay output for alarm connection
4. GND
5. Sensors connection
6. Audio speakers output
7. CVBS output
8. AUX monitor connection for viewing without OSD
9. SPEED DOME/Keyboard connection
10. Video channels inputs
11. HDMI connection
12. USB port
13. LAN port
14. VGA output for monitor connection
1. GND
2. SPEED DOME/Keyboard connection
3. Relay output for alarm connection
4. Sensors connection
5. HDMI connection
6. VGA output for monitor connection
7. LAN port
8. USB port
9. 12 V DC Power supply
10. Audio channels inputs
11. Video channels inputs
12. Audio speakers output
13. CVBS output
14. AUX monitor connection for viewing without OSD
Page 3 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
HOW TO SWITCH THE DVR ON AND OFF
To switch on the DVR
Connect the videocamera to the monitor, connect the DVR to the power supply. The blue LED switches on and the WIZARD window appears on the screen.
To switch o the DVR
The DVR can be switched o by using either the IR remote control or the mouse.
• with the remote control
Press the remote control's power button; the SHUT DOWN window will appear on the screen. Click OK.
• using the mouse
Access MENU and select SHUT DOWN. CLICK OK.
⚠It is always advisable to disconnect the power supply cable after performing all shutting down procedures.
WIZARD
Switch on the DVR. A WIZARD will appear on the monitor.
You can congure: TIME, NETWORK, RECORDING TYPE and HARD DISK HANDLING.
Click DEVICE NAME and the keyboard will appear.
You can enter DIGITS, LETTERS, SYMBOLS. Use SHIFT to enter capital letters and symbols.
Click on NEXT to congure the port.
Page 4 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
http port: default 88
SERVER port: preset 6036
You can:
a- Check OBTAIN AN IP ADDRESS AUTOMATICALLY
b- Manually enter the parameters shown below.
IP ADDRESS
SUBNET MASK
GATEWAY
PREFERRED DNS SERVER
ALTERNATE DNS SERVER : this selection allows you to remotely use/view the DVR.
CH (CHANNEL)
RESOLUTION : select the type registration resolution
FPS: select the number of frames per second
ENCODE: select the type of encoding
QUALITY: select the quality
MAX BITRATE: select the maximum BITRATE. The greater the value, the clearer the image and the greater the space taken up on the hard drive.
Click on NEXT to access the window for managing the hard drive.
⚠If the HARD DRIVER is just installed, proceed to format it.
ID
TYPE
SIZE[GB]
FREE (GB)
STATUS
PROPERTIES
SOURCES
Click on NEXT to view the state of the DVR.
Click FINISH to exit the WIZARD.
Click EXIT to not carry out the wizard.
Page 5 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
SCHEDULE
This window lets you schedule recordings. There are four dierent recording modes.
Manual recording press REC on the DVR. To end recording, press REC again.
☞You can use the mouse to start/end recording by clicking REC on the tool bar.
Scheduled recording
BASIC: to set up the video system, the language menu, the audio, the time and the authorizations control.
LIVE: to set up the NAME/TIME to view, the images' color and hide the videocameras.
RECORD: to set up the recording quality, the photograms' frequency, the resolution, time and recycling.
SCHEDULING: the schedule recordings, motion detection, and the alarm.
ALARM: set up the sensor type, alarm and buzzer activation.
NETWORK: to enable the feature, congure the IP address, the DDNS and the video transmission parameters.
USERS: to add, delete or modify their authorizations. This procedure can only be done by the administrator.
P.T.Z.: videocamera pan, tilt and zoom.
ADVANCED: to relaunch the DVR, import or export data from/on external drives.
SETUP
Press the MENU button or, using the mouse, right click to access the SETUP window.
LOGIN (LOGIN)
Press the MENU button to view the LOGIN window. Enter USERNAME and PASSWORD.
Username: admin Password: 123456
Page 6 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
The recording starts and ends a the preset times.
From SETUP select SCHEDULE. Click on to schedule recording. Click on to cancel scheduling.
Double clicking on the grill brings up the weekly scheduling window. On WEEK DAYS select the day and click ADD to set up the recording starting and
ending times.
Click COPY to copy the settings you have just made to other days. Select OL to save the weekly schedule.
The schedule recording procedure needs to be done for each CHANNEL, but you can also set the same schedule on all of the channels by selecting APPLY
SETTINGS TO ALL and clicking COPY.
Record on movement
Recording activates when a sensor detects any movement.
From SETUP select MOTION.
Enable the motion detection by checking ENABLE next to the channel (CH) on which you wish to activate the movement recording.
Click APPLY to save the settings. In the AREA box click SETTING to set the detection area and sensitivity.
Sensor recording
From SETUP select SCHEDULE, SENSOR, BASIC.
Enable the sensor alarm by checking ENABLE next to the channel (CH) on which you wish to activate the sensor recording.
Click APPLY to save the settings. Then select SCHEDULE to view the saved settings.
Page 7 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
PLAYBACK
There are four dierent playback modes.
LIVE playback
To launch LIVE playback click on on the main menu bar of the SEARCH window. Use the displayed controls to view playback.
Playback with TIME SEARCH
From MENU, SEARCH, select TIME SEARCH.
On the right side of the window, select the date and channels.
Click SEARCH. Give the recording start and end times.
Click to launch the searched playback.
Page 8 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
Playback with EVENT SEARCH
From MENU, SEARCH select EVENT SEARCH.
On the right side of the window, select the data and channels. Click on SEARCH.
Depending on the search you want to make, check MOTION, SENSOR or ALL.
The events will appear. Select the event by double clicking.
Playback with IMAGE
From MENU, SEARCH select IMAGE
On the right side of the window, select the data and channels. Click on SEARCH.
When the image you are searching is found, you can playback by double clicking on the image.
Click LOCK to block the image, while clicking SAVE, saves the image to the hard drive.
Click to SAVE ALL, to save all images onto the hard drive.
⚠To save images, activate the feature TAKE SNAPSHOT on the ALARM HANDLING window.
BACKUP
BACKUP is available via UBS.
From the BACKUP window you can set the backup starting and ending time and select the channels.
The ALL feature lets you back up everything.
The set BACKUP options can be controlled by users.
BACKUP starts by clicking on the START button.
REMOTE CONTROL
Remote control is only available if the DVR is connected to the LAN/WAN or to the internet.
Accessing the DVR via the LAN
MENU, SETUP, NETWORK and select the NETWORK card.
Enter the following data into the card
IP ADDRESS
SUBNET MASK
GATEWAY
If using the DHCP, you need to enable it on both the DVR and the ROUTER.
You can control the DVR's network settings from the INFORMATION window.
To set the network video parameters, photogram frequency, and so on) select RECORD SETUP.
Open the browser and enter the DVR's IP address and press send.
The ActiveX component is downloaded from the browser.
⚠If the http port is not the default one (80), enter the http port after the IP address.
You will need to provide USERNAME and PASSWORD.
Page 9 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
Accessing the DVR via WAN
MENU, SETUP NETWORK
Enter IP ADDRESS, SUBNET MASK and GATEWAY.
If using the DHCP, you need to enable it on both the DVR and the ROUTER.
Forward the IP ADDRESS and the port number on the ROUTER's or virtual server's VIRTUAL SERVER. Congure the rewall to permit access to the DVR.
☞Avoid this step if the UpnP feature is enabled in the DVR and ROUTER.
Open the browser, enter the IP ADDRESS or the dynamic domain name and press ENTER.
⚠If the http port is not the default one (80), enter the http port after the IP address.
You will need to provide USERNAME and PASSWORD.
Connecting the DVR to the internet via PPPoE
From MENU, SETUP NETWORK, enable PPPoE, then enter USERNAME and PASSWORD. Click on APPLY
The DVR connects to the server and sends a conrmation message.
You can use a dynamic domain name, requesting it from the DNS server that works with the DVR or Router. This dynamic domain name needs to be
added to the DVR or to the Router.
When remotely accessing, entering the IP ADDRESS, will provide direct access.
The ActiveX component is downloaded from the browser.
APPENDIX
Control from mobile device
⚠Enable the network service on the DVR.
Supported operating systems:
WINDOWS MOBILE
SYMBIAN
iOS
ANDROID
BLACKBERRY OS
Supported network: 3G
Tests made on: Dopod D600 (WM5) and Dopod S1 (WM6)
WINDOWS MOBILE
Activate the network access on the smartphone and open the browser. Enter the server address. The connection will be created.
Click on the software's name (PCam). The DOWNLOAD window will appear. Select YES.
The PCam software will open automatically.
Page 10 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
In the SERVER eld enter the server address.
In the USER eld enter the following user name (admin).
In the PASSWORD eld enter the following password (123456).
Click GO.
After LOGIN, CAM1 is the preset one on channel 1. You may change the channel.
SYMBIAN
Supported versions:
Symbian S40, Symbian UIQ, Symbian S80, Symbian S60, Symbian S60 3rd Edition-Symbian OS v9.1, Symbian S60 3rd Edition con FP 1-Symbian OS v9.2,
Symbian S60 3rd Edition with FP2-Symbian OS v9.3, Symbian S60 5th Edition-Symbian OS v9.4, Symbian S60 5.1 Edition-Symbian OS v9.5
Activate the network access on the smartphone and open the browser. Enter the server's IP address. Establish the connection.
Download the software. Select YES when the installation security window appears. An antifraud program will also install. Execute the program.
Page 11 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
Access the installed software and select SYSTEM SETTING, LOGIN SETTING.
To types of viewing are possible: LIVE VIEW and IMAGE view.
A HELP feature is also available.
Enter the server address, ID and password. Save.
⚠THE ACCESS POINT and SERVICE PROVIDER dier depending on the country.
Access LIVE VIEW.
USERNAME and PASSWORD : admin / 123456.
With LIVE VIEW you can take photographs, change channels and control the PTZ.
Page 12 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
iOS
On AppleStore nd SUPERLIVE_pro. Install the application onto the phone. The iPhone will request a password to continue the installation, even if
the application is free.
In case you are using a PC instead of a smartphone:
Install iTunesStore on the PC, and connect the iphone to the PC. Download the SUPERLIVE_pro. application from iTunes. Then iTunes will ask for
username and password.
Continue with the download.
SUPERLIVE_pro LOGIN interface.
Page 13 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
Server: enter the server's IP address
Account: enter the user name
Password: enter the password
By checking the Remember server box, you can, then, access quickly.
Icon legend:
View image Four channels
Play Snapshot
Setting Recording
View information Audio
Server list Microphone
Disconnecting Color
Single channel PTZ
PTZ rotation up PTZ rotation left
PTZ rotation down PTZ rotation right
Stop PTZ rotation Zoom IN / Focus IN / Iris ADD
Zoom OUT / Focus OUT / Iris SUB Next
Previous Preset Select preset point
Cruise Set cruise Speed PTZ speed rotation
Android
Download the Supercam application from Google Market and install it.
Page 14 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
Supercam LOGIN interface
Server: enter the server's IP address
User: enter the user name
Password: enter the password
By checking the Remember server box, you can, then, access quickly.
Playback Play recording
Image Viewing images
Log Event log
Server List Server list
Live Live viewing
Settings Settings
Information Device information
Help Help
Logo Disconnecting
Page 15 - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A. - The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
Stop copying
Screen mode
Snapshot
Conversation
Live audio
View single channels
Four channel viewing
PTZ
Recording
Hide
Blackberry
From your smartphone, open the browser and enter the server address. Click on Supercam and download it. If it doesn't download, delete the
cache from the browser. With touch screen smartphones, there may be compatibility issues with the Supercam application. To solve this, disable
compatibility from the options menu.
Image Viewing images
Log Event log
Server List Server list
Live Live viewing
Settings Settings
Information Device information
Help Help
Logo Disconnecting
Symbol 1 Current viewing channel Symbol 2 Channel status
Change channels PTZ, click to go to interface
Snapshot Full screen
Alarm in background Stop PTZ rotation
PTZ upwards rotation PTZ downwards rotation
PTZ left rotation PTZ right rotation
Zoom In/Focus In/Iris Add Zoom Out/Focus Out/Iris Sub
Preset Select preset point Gruppo Import cruise line
Came S.p.A.
Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c
31030 Dosson di Casier
Treviso - Italy
33079 Sesto al Reghena
Pordenone - Italy
(+39) 0422 4940
(+39) 0422 4941
(+39) 0434 698111
(+39) 0434 698434
www.came.com
English - Manual FA00305-EN - ver. 1 - 11/2015 - © Came S.p.A.
The contents of the manual are to be considered as subject to change at any time and without the need for any advance warning.
/
