CAME XDTVI23 Installation guide

CAME
Brand
CAME
Model
XDTVI23
Category
Digital Video Recorders (DVR)
Type
Installation guide
SETUP AND USE MANUAL
XDTVI2304 - XDTVI2304H
XDTVI2308 - XDTVI2308H
XDTVI2316 - XDTVI2316H
FA00178-EN
E
n
g
l
i
s
h
EN
DIGITAL VIDEO RECORDERS
Page
2
2 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
INSTALLING THE HARD DRIVE
Came S.p.A. recommends using a SATA hard drive. Before installing, disconnect power.
The hard drive must be secured to the bottom of the DVR, after connecting the power cord and the data cable.
Description of the components
Rear panel XDTVI2304 - XDTVI2304H
Rear panel XDTVI2308 - XDTVI2308H
Rear panel XDTVI2316 - XDTVI2316H
Reference Description
AUDIO OUT Audio channel output
AUDIO IN Audio channel input
A B - RS 485 Keypad or Speed Dome input. A = TX+ / B = TX-
HD TVI VIDEO IN HD-TVI or Analogue Video Inputs
HDMI Output for connecting HDMI monitor
VGA Output for connecting VGA monitor
LAN LAN port
USB USB port
DC12 V 230 V AC power supply
DESCRIPTION
Digital video recorder with 4, 8 and 16 inputs.
Page
3
3 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
HOW TO TURN THE DVR ON AND OFF
To turn the DVR on
Connect the camera to the monitor, connect the DVR to the power supply. The blue LED will light up and the
WIZARD window will appear on the monitor.
To turn the DVR o
The DVR can be turned o using either the IR remote control or the mouse.
• Using the remote control
Press the power button on the remote control. The SHUT DOWN window will appear in the monitor. Click OK.
• Using the mouse
Enter the MENU and select (o ). Click .
It is always advisable to unplug the power cord after shutdown.
Turn the DVR on The WIZARD window will appear on the
monitor.
You can enter NUMBERS, LETTERS and SYMBOLS. Use
the SHIFT key to enter capital letters and symbols.
You can confi gure: TIME, NETWORK, TYPE OF
RECORDING and HARD DRIVE MANAGEMENT.
Click DEVICE NAME and the keyboard will appear, then
click NEXT to confi gure the port.
WIZARD
Http port: default 80
SERVER port: default 6036
You can:
a- Check OBTAIN AN IP ADDRESS AUTOMATICALLY
b- Manually enter the following parameters.
IP ADDRESS
SUBNET MASK
GATEWAY
PREFERRED SERVER DNS
ALTERNATE DNS SERVER: this selection allows you to use/display the
DVR remotely.
Page
4
4 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
CH (CHANNEL): recording channel
RESOLUTION: choose the type of recording resolution
FPS (FRAMES PER SECOND): choose the number of frames per second
ENCODE: choose the type of coding
QUALITY: choose the video quality
MAX BITRATE: choose the maximum BITRATE. The higher the value, the sharper the image and the greater the space occupied
on the hard drive.
Click NEXT to access the hard drive management window.
If the HARD DRIVE has just been installed, proceed with formatting.
ID
TYPE
SIZE (GB)
FREE (GB)
STATUS
PROPERTIES
SOURCES
Click NEXT to view the status of the DVR.
Click FINISH to end setup and exit the procedure.
Click EXIT if you do not want to run the wizard.
Page
5
5 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
SCHEDULE
From this window, you can schedule recording. There are 4 di erent recording modes.
Manual recording pressing REC on the DVR. To stop recording, press REC again.
You can use the mouse to start/stop recording by clicking REC on the toolbar.
LOGIN
Press the MENU button to display the LOGIN window. Enter USERNAME and PASSWORD.
Username: admin
Password: 123456
SETUP
Press the MENU key or click the right mouse button to access the SETUP window.
BASIC: to set the video system, menu language, audio, time and authorisation control.
LIVE: to set the NAME/TIME to display, the image colour and to hide the cameras.
RECORD: to set the recording quality, frame rate, resolution, time and recycling.
SCHEDULE: to schedule recordings, motion detection, alarms.
ALARM: to set the type of sensor, alarm activation and the buzzer.
NETWORK: to enable the function, confi gure the IP address, the DDNS and the video transmission parameters.
USERS: to add or delete users or modify their permissions. This can only be done by the administrator.
PTZ: camera pan, tilt and zoom.
ADVANCED: to reboot the DVR, import or export data from to external drives.
Scheduled recording
Page
6
6 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Recording begins and ends at set times on set days.
From SETUP, choose SCHEDULE. Click to schedule recording. Click to cancel the scheduling.
If you double-click on the grid, a weekly programming window appears. On WEEK DAYS select the day and click
ADD to set the recording start times and end times.
If you click COPY, you can copy the settings you just have entered to other days. Click OK to save the weekly
schedule.
Recording must be scheduled for each CHANNEL, but you can also set the same schedule for all channels by
selecting APPLY SETTINGS TO ALL and clicking COPY.
Recording when motion is detected
Recording is activated when a movement is detected by a sensor.
From SETUP choose MOTION.
Enable motion detection by checking ENABLE next to the channel (CH) on which you want to enable recording
when motion is detected.
Click APPLY to save the settings. In the AREA box, click SETTING to set the detection area and sensitivity.
Recording using a sensor
From SETUP, choose SCHEDULE, SENSOR, BASIC.
Enable the sensor alarm by checking ENABLE next to the channel (CH) on which you want to enable recording
when using a sensor.
Click APPLY to save the settings. Then choose SCHEDULE to view the saved settings.
Page
7
7 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
PLAYBACK
There are 4 di erent ways of playing the recording.
LIVE playback
To start LIVE playback, click from the main menu bar in the SEARCH window. Use the commands on the
display to view the video playback.
Playback with TIME SEARCH
From MENU, SEARCH choose TIME SEARCH.
On the right-hand side of the window, select the date and channels.
Click SEARCH. Indicate the start time for recording playback.
Click to start playback.
Page
8
8 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Playback with EVENT SEARCH
From MENU, SEARCH choose EVENT SEARCH.
On the right-hand side of the window, select the date and channels. Click SEARCH.
Depending on the search you want, check MOTION, SENSOR or ALL.
The events will appear. Select the event with a double-click.
Playback with IMAGE
From MENU, SEARCH choose IMAGE
On the right-hand side of the window, select the date and channels. Click SEARCH.
When you fi nd the image you are looking for, you can start playback by double-clicking the image.
If you click LOCK, you can freeze the image, while clicking SAVE saves the image on the hard drive.
If you click SAVE ALL, all images will be saved on the hard drive.
In order to save the images, activate the SNAPSHOT function in the ALARM HANDLING window.
BACKUP
BACKUP is available via UBS.
From the BACKUP window, you can set the start and end times for backup and select the channels.
Using the ALL function, you can back up everything.
The BACKUP options set can be controlled by the user.
BACKUP starts when you click START.
REMOTE CONTROL
Remote control is only possible if the DVR is connected to the LAN/WAN or internet.
Accessing the DVR via LAN
MENU, SETUP, NETWORK and choose the NETWORK tab.
Enter the following data
IP ADDRESS
SUBNET MASK
GATEWAY
If you are using the DHCP, you must enable it on both the DVR and the ROUTER.
You can check the network settings of the DVR from the INFORMATION window.
To set the network video parameters (resolution, frame rate...) select RECORD SETUP.
Open a browser, enter the IP address of the DVR and press enter.
The browser will download the ActiveX component.
If the http port is not the default one (80), specify the http port number after the IP address.
You will be asked for your USERNAME and PASSWORD.
Page
9
9 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Accessing the DVR via WAN
MENU, SETUP, NETWORK
Enter IP ADDRESS, SUBNET MASK and GATEWAY.
If you are using the DHCP, you must enable it on both the DVR and the ROUTER.
Forward the IP ADDRESS and the port number on the ROUTER’s VIRTUAL SERVER or the virtual server. Confi gure
the fi rewall to allow access to the DVR.
This step should not be done in the event that the UPnP function is enabled in the DVR and ROUTER.
Open the browser, enter the IP ADDRESS or the name of the dynamic domain and press enter.
If the http port is not the default one (80), specify the http port number after the IP address.
You will be asked for your USERNAME and PASSWORD.
Connecting the DVR to the internet via PPPoE
From MENU, SETUP, NETWORK enable PPPoE, then enter your USERNAME and PASSWORD. Click APPLY.
The DVR connects to the server and sends a confi rmation message.
You can use a dynamic domain name by requesting it from a DNS server supported by the DVR or router. This
dynamic domain name should be added to the DVR or router.
In the case of remote access, if you enter the IP ADDRESS, you can access directly.
The browser will download the ActiveX component.
APPENDIX
Control from mobile device
Enable network service on the DVR.
Operating systems supported:
iOS
ANDROID
iOS
From AppleStore, search for SUPERLIVE_pro. Install the application on your phone. Your iPhone will ask for the
password in order to proceed with installation, although the application is free.
Page
10
10 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Android
Download the SuperCam app from Google Market and install it.
DDNS AND UPNP SETUP
UPnP setup
You can use UPnP to enable rapid connection of the device to the WAN through a router, without port mapping.
1. Access the Other Settings tab, enable UPnP and click “Apply” to save.
2. Enable UPnP on the router.
Before setting UPnP, correctly confi gure the local IP address, subnet mask, gateway and DNS according to
the router. Make sure that the HTTP port and the data port are set correctly. Check that your router supports
UPnP.
NAT
NAT settings
1. The DVR must be powered on and connected to the network.
2. Access Menu Setup Network. See Figure 1. IP address, Subnet Mask and Gateway can be
obtained automatically, but you can enter them manually according to the PC setup.
Make sure that the network segment is the same as the network used.
3. Set the preferred or alternate DNS server. Click “Apply” to save the parameters.
Quick DDNS setup
You can setup the DDNS to use when the DVR is set to use PPPoE
as the network connection.
1. Access Main Menu Setup Network Other Settings.
2. Enable DDNS and select “www.autoddns.com” in the dropdown
DDNS Type menu. The host name is set automatically. Once
you register, save the settings by clicking “Apply”. At this point,
you can remotely access the DVR using the domain name via
WAN.
Page
11
11 - Manual
FA00178-EN
FA00178-EN - ver.
1
1 - 11/2015 - © Came S.p.A - The contents of this manual are subject to change at any time without prior notice.
Figure 1 Figure 2
PSP Setup
Once the application is open, tap the arrow highlighted in red , tap the highlighted key and check that the
address and port are as shown . If necessary, enter the address 115.28.222.212:8989.
Accessing the NAT server
After fi nishing the NAT settings, you can access the NAT server on the
PC (enter http://www.autonat.com to access the IE client). If you are
accessing NAT for the fi rst time, the network will automatically downlo-
ad ActiveX. After installing ActiveX, the login window will open up:
Serial No: DVR MAC address (access Menu Information
Network to check the DVR MAC address).
User Name: DVR username (the default name is admin).
Password: the DVR password (the default password is 123456).
4. Access Menu Setup Network NAT tab. See Figure 2.
5. Enable NAT and fi ll in the NAT Server and Port number fi elds (the default NAT Server value is www.
autonat.com; the default Port number value is 8989).
6. Click “Apply” to save the parameters.
www. came.com
www. came.com
Came S.p.A.
Came S.p.A.
Via Martiri Della Libertà, 15 Via Cornia, 1/b - 1/c
31030
Dosson di Casier
Dosson di Casier
Treviso
Treviso - Italy
33079
Sesto al Reghena
Sesto al Reghena
Pordenone
Pordenone - Italy
(+39) 0422 4940
(+39) 0422 4941
(+39) 0434 698111
(+39) 0434 698434
English - Manual FA00178-EN - ver. 1 - 11/2015 - © Came S.p.A.
The contents of this manual are subject to change at any time without prior notice.
At this point, simply tap the typical icon to read the QR code (in red ). The code scan window opens up .
Once read, the serial number will be shown in the “Server” box . At this point, simply enter your username
and password to gain access to the VCR.
If, on the other hand, you intend to access the VCR using a PC, always via P2P, you must fi rst reach the
address 115.28.222.212 (you may be prompted to install the plug-in). The page will open . Now just enter
the VCR serial number and your username and password to gain access.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

CAME XDTVI23 Installation guide

CAME
Brand
CAME
Model
XDTVI23
Category
Digital Video Recorders (DVR)
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents