Page is loading ...
S P E C F I L E
ET-PKD110H
Ceiling mount bracket for high ceilings
As of October 2010
SFD10A015
1 / 1
DLP and the DLP logo are trademarks of Texas Instruments.
Weights and dimensions shown are approximate. Specifications subject to change without notice.
∅ 60.5
(∅ 2-3/8)
340 –420 *
(13-3/8 –16 -17/32)
431–511*
(16-31/32–20-1/8)
100
(3-15/16 )
100
(3-15/16 )
Attachment
plate
Attachment plate
*
Adjustable in
40 mm (1-9/16˝) steps
Projector
100
(3-15/16)
100
(3-15/16)
253.5
(9-31/32)
231
(9-3/32)
200 (7-7/8)
200 (7-7/8)
344 (13-17/ 32)
300 (11-13/16)
12
(∅ 15/32)
2-3-R6
(2-3-R1/4)
Specifications
Vertical correction angle: +5°, -17°
Horizontal slant correction angle: ±2.5°
Horizontal turn correction angle: ±1.2°
Dimensions (W × H × D): 344 × 340–420 × 300 mm
(13-17/32˝ × 13-3/8˝–16-17/32˝ × 11-13/16˝)
Weight: Approx. 9.2 kg* (20.3 lbs*)
Attachment plateIllustration shows the bracket attached to a projector.
Parts
Attachment plate . . . . . . . . . . . . . . . . . . . . . . . . 1
Projector mount bracket . . . . . . . . . . . . . . . . . . . 1
Adjuster pole A . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Adjuster pole B . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Angle adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pole support bracket 1 . . . . . . . . . . . . . . . . . . . . 1
Pole support bracket 2 . . . . . . . . . . . . . . . . . . . . 1
Pole fixing bracket . . . . . . . . . . . . . . . . . . . . . . . 1
Washer-fitted bolts (M6 × 80) . . . . . . . . . . . . . . . 2
Washers (M6) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Hexagonal nuts (M6) . . . . . . . . . . . . . . . . . . . . . . 2
Washer-fitted screws (M4 × 12) . . . . . . . . . . . . . 4
Washer-fitted screws (M6 × 12) . . . . . . . . . . . . 30
Seal packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
*
A
verage value. May differ depending on models.
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
Dimensions
Description
This ceiling mount bracket is used when mounting a PT-DZ570 series DLP
™
projector to high ceilings.
C a u t i o n :
• Mounting should be done by a qualified technician.
• Make sure that the mounting (ceiling) area has sufficient strength.
• Read the enclosed mounting instructions thoroughly before starting.
• Do not use an electric screwdriver or impact driver to tighten screws. Use a torque driver or hexagon torque
wrench and tighten screws to the torque specified in the instructions.
• When the product is no longer going to be used, have it disposed of quickly by a professional disposal service.
/