Fametech TP-8515 User manual

1

Service Manual

TP-8515

Modular POS System

Service Manual

TP-8515

Version 1.0

I

Table of Contents

Table of Contents ....................................................................................... I

I Parts Description ................................................................................. 1

A Examining Your POS Terminal ................................................................... 1

Parts Descriptions................................................................................................... 1

Main Board Layout ................................................................................................. 3

II System Disassembly ........................................................................... 8

A Before You Start .......................................................................................... 8

B Disconnect the Devices on the I/O Ports .................................................. 9

a. Unplug the cables from the POS unit. .............................................................. 9

b. Remove the Main LCD Unit ............................................................................ 11

c. Remove the MSR or i-Button Module from the Main LCD Unit ....................... 13

d. Remove the Secondary LCD Display (Optional) ............................................ 15

e. Remove the Customer Display (Optional) ...................................................... 17

C Remove the HDD/SSD Drive from POS Unit ........................................... 19

D Modular Main Board Set ........................................................................... 21

a. Remove the Modular Main Board Set from the POS Unit ............................... 21

b. Remove the Power Adaptor from the Modular Main Board Set ...................... 23

c. Remove the HDD/SSD Drive from the Modular Main Board Set .................... 24

d. Disconnect the HDD Cable ............................................................................ 26

e. Disconnect the Parallel (PRT) Port (for Customized Model ONLY) ................ 27

f. Remove the Speaker (Audio) from Main Board .............................................. 28

g. Disconnect the DB9 COM Port (COM 4) ........................................................ 29

h. Remove the RAM Module .............................................................................. 30

i. Disassemble the Main Board Set ................................................................... 31

j. CMOS Battery Replacement .......................................................................... 33

E Base Unit Maintenance ............................................................................. 34

Table of Figures

Figure 1 Parts of POS Unit............................................................................ 1

Figure 2 Main Board ...................................................................................... 7

1

I Parts Description

A Examining Your POS Terminal

Parts Descriptions

Figure 1 Parts of POS Unit

TOP I/O Cover

A. Main LCD

Display

B. Base Unit

Side Cover

(Left)

Side Cover

(Right)

Modular

Main Board

Set

C. Modular

Customer Display

D. 2

nd

LCD Display

A1. MSR

A2. -Button

2

 POS Unit

No.

Item

Description

A

Main LCD Display

Modular LCD Display with Touch Screen.

B

Base Unit

Metal Housing (with Top I/O Cover and Side Covers)

POS Modular Main Board Set and Main Power Adaptor

 Optional Peripherals

Optional Peripherals

A1

MSR

Optional MSR Reader on the side of Main LCD Display

A2

i-Button

Optional i-Button Module on the side of Main LCD

Display

C

Modular Customer Display

Optional Customer Display.

D

2nd LCD Display

Optional Secondary (2

nd

) LCD Display.

* The optional peripherals and parts may not include in the product. Please contact the local

representatives or technical support personnel of the providers for ordering information.

3

Main Board Layout

● Main Board Connection / Installation Notes

The images below indicate the connectors and jumpers of the main board.

Each connector/slot is used for the specified part or optional peripheral.

Please refer to the notes as below and examine the layouts of the main boards to locate

the connectors so as to complete the installation.

i.e.:

To connect the HDD to the main board, please use the HDD cable and locate the

matched connector on the main board; then connect the HDD cable to the Hard Drive.

Connector/Slot

Connection/Installation Notes

Memory Slot 1

Install the RAM module to the main board.

SATA Connectors

Please use the SATA HDD cable and connect to the

Hard drive.

USB

Connect to the devices that support USB interface.

COMBO USB

Connect to the optional MSR Module and the USB port

under the Main LCD Display.

PWR LED / PWR SW

Connect to Power Switch and LED Indicator

LVDS Connector

Use the LVDS Cable and connect to the LCD Panel.

eDP Connector*

The LCD Panel with eDP connector.

This is reserved for customized model only and not

available for standard model.

Speaker (Audio Connector)

Connect the Speaker to the main board.

4

● Main Board

Front View

Speaker

(SP2)

JDIO1

COM 1

COM 2

LPT1

(Parallel Port)

COM 5 / COM 6

SATA DATA

Connectors

Memory Slot 1

(Main Slot)

VGA 1

COM 3

SATA

POWER

CN4

(COMBO USB)

LAN

USB 3/4

USB 1

USB 2

CASH 1

VGA_Power

VJ1

(PWR_IN)

Speaker

(SP1)

COM

Jumper 1-6

JLPC1

MINI CARD 1_1

COM 4

MIC1

LOUT1

JCMOS1

JCASE1

5

Front View

(Layout)

6

Rear View

LVDS

eDP*

7

Rear View (Layout)

Figure 2 Main Board

Note:

The eDP connector is for customized model Only and is not available for standard model.

8

II System Disassembly

A Before You Start

 To prevent injuries to the LCD Panel:

Carefully Place the POS terminal on a flat, clean and stable surface

(for example: a stable long table)

 Prepare additional cushioned material (for example: a soft, clean blanket).

 Terminate the application running in the POS system, and shut down the

operation system.

 Turn-off the power of POS terminal and optional peripherals

(for example: Thermal Receipt Printer, Secondary LCD Display)

 Disconnect all the devices or cables connected to the POS terminal.

 Disconnect and remove the Power Adaptor from the POS terminal.

 Unplug the power cables from the electrical outlet.

Note:

 There are no serviceable parts or components in the POS system or peripherals.

DO NOT modify any parts of POS systems or use non-qualified parts or peripherals.

 Store the disconnected parts, cables, devices and screws in a secure location for

further use.

 For maintenance or replacement, please consult the technical personnel and contact

the local representative for purchasing the new peripherals and parts

9

B Disconnect the Devices on the I/O Ports

There are some of the optional peripherals installed onto the POS system.

Please detach the peripherals and store them in a secure location.

Note:

Please turn off the whole POS system and unplug the power cables from the electrical

outlet.

a. Unplug the cables from the POS unit.

Place the POS terminal onto a

stable and flat location

Examine the bottom of Main LCD Display

Main Power Switch of POS Unit

(on the bottom of Main LCD Display)

1. Examine the bottom of

Main LCD Display.

Disconnect the device of the USB

port (if connected).

USB port of Main LCD Display

2. Lift up the whole POS unit and

examine the Bottom I/O ports

beneath the Base Unit.

Bottom I/O ports and Power Adaptor with

Power Cable connected

10

Bottom I/O Ports with connected cables

Bottom I/O Ports

(Cables Disconnected)

3. Disconnect the Power Cable from

the POS unit.

Disconnect the Power Cable

from the Power Adaptor

4. Disconnect all of the connected

cables on the Bottom I/O Ports.

Note:

Always store the Power Cable and the other disconnected cables/devices in a secure

location for further use.

11

b. Remove the Main LCD Unit

Base Unit of POS Terminal

LVDS Cable (Left) and

COMBO USB Cable (Center)

COMBO USB Connector with HEX Head Screws

1. Press the two sides and pull up to

remove the TOP I/O Cover.

Top I/O Cover

2. There are LVDS cable and COMBO

USB cable in the

Base Unit.

Unplug the LVDS cable.

Unplug the LVDS Cable

3. Use a HEX screw driver to remove

the HEX screws of the

COMBO USB Connector.

Remove the HEX Head Screws

12

TOP I/O Ports and

Main LCD Unit Securing Screws

(as RED marks indicated)

Detach the Main LCD Unit from the Base Unit.

Main LCD Unit with MSR Module.

4. Disconnect the COMBO USB

Connector from the

TOP I/O Port.

5. Use a screw driver to remove the

four securing screws of the

Main LCD Unit.

Note:

Main LCD Unit is an integrated part and should not dissemble or modify.

ANY ATTEMPT OF MODIFICATION OR DISSEMBLE IS PROHIBITED AND THE WARRANTY

OF THIS PRODUCT IS TERMINATED IMMEDIATELY.

Please contact the authorized and certificated technical personnel for maintenance.

13

c. Remove the MSR or i-Button Module from the Main LCD Unit

Main LCD Unit with MSR Module.

Protective Caps of MSR Module

Detached MSR Module with Protective Caps

and Securing Screws

1. Remove two Protective Caps of

MSR Module with care.

2. Use a screw driver to loosen and

remove the securing screws.

Loosen the securing screws of MSR Module

3. Disconnect the ribbon cable

connector of MSR Module from the

Main LCD Unit.

Disconnect the MSR Module from the

Main LCD Unit

14

Side I/O Port of the Main LCD Unit and the

Protective Cover (Left)

4. Side I/O Port Protection:

If the Side I/O Port of the

Main LCD Unit is not in use, please

install the protect cover onto the

I/O Port.

Note:

Always store the detached MSR Module (or i-Button) and screws in a secure location for

further use.

15

d. Remove the Secondary LCD Display (Optional)

Secondary LCD Display

12VDC Power Output (Left) and

VGA Connector (Right)

1. Press the two sides and pull up to

remove the TOP I/O Cover.

Top I/O Cover

2. Lift up the POS Unit and examine

the Bottom I/O connectors.

Disconnect the connectors of

Secondary LCD Display.

Disconnect the VGA Connector from the

Bottom I/O Ports.

3. Use a screw driver to remove the

four securing screws of the

Secondary LCD Display.

16

Base Unit

(Secondary LCD Display detached)

Secondary LCD Display

4. Arrange the cables and remove the

Secondary LCD Display from the

Base.

Note:

Store the detached Secondary LCD Display and securing screws in a secure location for

further use.

17

e. Remove the Customer Display (Optional)

Customer Display

12VDC Power Output (Left) and

DB9-Type COM Connector (Right)

5. Press the two sides and pull up to

remove the TOP I/O Cover.

Top I/O Cover

6. Lift up the POS Unit and examine

the Bottom I/O connectors.

Disconnect the connectors of

Customer Display.

Disconnect the Connectors of Customer

Display from the Bottom I/O Ports.

7. Use a screw driver to remove the

four securing screws of the

Customer Display.

18

Base Unit

(Customer Display detached)

Customer Display

8. Arrange the cables and remove the

Secondary LCD Display from the

Base Unit.

Note:

Store the detached Customer Display and securing screws in a secure location for further

use or maintenance.

Page is loading ...

Fametech TP-8515 User manual

Fametech TP-8515 User manual

Other documents