Apantac W-2×2-H APANTAC Mt Hood FHD Video Wall Controller User manual

Brand: Apantac

Model: W-2×2-H APANTAC Mt Hood FHD Video Wall Controller

Category: Video splitters

Type: User manual

APANTAC LLC www.apantac.com i

W-2x2-H User Manual

W-2x2-H

APANTAC Mt Hood

FHD Video Wall Controller

User Manual

Updated: January 2023

APANTAC LLC www.apantac.com i

W-2x2-H User Manual

Features ................................................................................................. 1

Contents ................................................................................................. 2

Front Panel ............................................................................................. 3

Back Panel .............................................................................................. 4

Basic Installation ..................................................................................... 5

Control and Configuration .............................................................................. 6

Video Wall Modes .................................................................................... 7

OSD Configuration Menu .......................................................................... 8

Specifications ........................................................................................ 10

Table of Contents

APANTAC LLC www.apantac.com 1

W-2x2-H User Manual

Features:

• 2x2 video wall processor

• 2x2, 1x4, and 4x1 Video Wall modes

• Optional HDMI splitter mode

• Supports up to 1080P and 1920x1200 input

• Supports up to four 1080P/1920x1200 outputs

• Bezel compensation

• Crop and Position

• On-screen Graphical User Interface

• Remote

APANTAC LLC www.apantac.com 2

W-2x2-H User Manual

• Main Unit

• Mounting Plate—Magnetically held

• 5-Volt, 4-Amp power supply

• Remote control

Contents:

APANTAC LLC www.apantac.com 3

W-2x2-H User Manual

VDO/PWR

Red LED: power indicator

Green LED: active video signal indicator

OUT 1 through OUT 4

HDMI video output ports. To be connected to displays/monitors.

Infrared sensor for the Remote control. If the unit is mounted in a location where this

sensor is not visible to the remote, an optional external IR sensor can be used.

Front Panel:

APANTAC LLC www.apantac.com 4

W-2x2-H User Manual

5V DC

Power adapter connection. Use only 5-volt DC (direct current) power.

IR EXT

Connection for optional external Infrared sensor for use with the Remote control.

Reset

Factory reset button is located inside the small hole.

USB

Factory use only.

HDMI IN

HDMI video input port. Connect your video source (i.e.; computer, media-player, etc).

VGA/YPbPr IN

Alternate videio input port. Accepts VGA or component video sources.

AA IN

Alternate Audio input. For use with Alternate video input sources not containing

embedded audio.

Back Panel:

APANTAC LLC www.apantac.com 5

W-2x2-H User Manual

Basic Installation:

Mounting Plate:

A metal mounting plate with screw holes

is held magnetically to the unit. The unit

can be separated from the plate by pull-

ing firmly.

HDMI

HDMI HDMI

HDMI

5VDC

Mounting

Plate

APANTAC LLC www.apantac.com 6

W-2x2-H User Manual

Control and Configuration:

Remote:

Only the buttons specifically mentioned below are used.

All other buttons on the remote perform no function on the

W-2x2-H model.

Video Wall Modes:

The W-2x2-H model has three video wall modes. They can

be selected by the “2x2”, “1x4”, and “4x1” buttons of the

remote.

Mute:

Enables or Disable audio on outputs.

Status OSD:

The Status OSD is displayed in the upper-left of all output

video displays. It can be displayed by pressing the OK

button (when not within the menu system).

The Status OSD contains both the Video-Mode and the

unit’s ID number on the first line.

APANTAC LLC www.apantac.com 7

W-2x2-H User Manual

Video Wall Modes:

Splitter Mode:

The W-2x2-H model can function as a simple video signal

splitter (distribution amp). Press the “Spltter” button of the

remote. All outputs will be identical to the input video.

Video Wall Modes:

The W-2x2-H model has three video wall modes. They can

be selected by the “2x2”, “1x4”, and “4x1” buttons of the

remote.

Note that the 1x4 and 4x1 modes will stretch the video

source image and correct aspect ratio will be lost. It is the

customer’s responsibility to provide content appropriate to

be used in these modes.

source

A1 A2

A3 A4

A1 A2

A2 A3

A3 A4

2x2 Mode

4x1 Mode

1x4 Mode

Original Source

APANTAC LLC www.apantac.com 8

W-2x2-H User Manual

OSD Configuration Menu:

OSD Navigation with the Remote:

Press the OK button to display and enter the menu. Use the up/down arrow keys to high-

light a menu item. Press the OK button to select the menu item. Use the left/right arrow

keys to change values when editing an item. Press the Exit button to return to the previ-

ous menu or to close the OSD menu.

Horizontal bezel:

Compensates for the display’s left and right bezel width by removing or hiding that portion

of the source video image.

Vertical bezel:

Compensates for the display’s top and bottom bezel width by removing or hiding that por-

tion of the source video image.

Crop (and Position):

The incoming video image can be cropped. Se-

lecting only a portion of it to display on the video

wall.

The ‘Crop Level’ sets the size of the cropped por-

tion. It is set in steps (not infinitely adjustable).

Once a Crop-Level is set, the Crop Position can

be adjusted using the arrow keys to move crop

selection within the original incoming video area.

APANTAC LLC www.apantac.com 9

W-2x2-H User Manual

OSD Configuration Menu:

Output resolution:

The output resolution and refresh rate can be set to the following selections:

• 1920x1080p 60Hz

• 1920x1080i 60Hz (interlaced)

• 1920x1080p 30Hz

• 1280x720p 60Hz

• 1280x720p 30Hz

• Auto (adjusts to EDID of the monitor on output 1)

Remote controller:

In the event you have more than one W-2x2-H, this sets the ID number of the unit.

APANTAC LLC www.apantac.com 10

W-2x2-H User Manual

Specifications:

Input 1 x HDMI or 1 x VGA/YPbPr

Audio Input 1 x 3.5mm phone jack

Outputs 4 x HDMI

Output Resoluons Auto, 1080p 60/30 Hz, 1080i 60Hz, 720p 60/30 Hz

Video Modes

2x2 video wall

1x4 video wall

4x1 video wall

Splier mode

Control Infrared remote

IR 1 x Receiver sensor, 1 x IR extender jack

Control Interface OSD (On Screen Display) menu system

Weight 470 g

Dimensions 120 x 134 x 26 mm

Environment

Operating temperature: 0 ~ 40 C,

Storage temperature : -20 ~ 60 C

Humidity: 0 - 90% RH (non-condensing)

Power 5-Volt, 4 Amp power adapter with locking DC plug

Power consumpon Approximately 10 was

Supported HDMI Input Resoluons

1080p (1920x1080) 60, 59.94, 50, 30, 29.97, 25, 24, 23.98 Hz

1080i (interlaced) Not supported

720p 50, 59.94, 60 Hz

576p 50 Hz

576i (PAL) Not supported

480p 59.94 Hz

480i (NTSC) Not supported

1280x1024

1280x960

1360x768

1280x768

1024x768

60 Hz

800x600

640x480 Not supported

APANTAC LLC www.apantac.com 11

W-2x2-H User Manual

or by any means without written permission from the product manufacturer. Changes are periodically made to the

information in this document. They will be incorporated in subsequent editions. The product manufacturer may

make improvements and /or changes in the product described in this document at any time.

All the registered trademarks referred to this manual are belonging to their respective companies.

WARRANTY STATEMENT

Apantac LLC (herein after referred to as “Apantac”) warrants to the original purchaser of the products manufactured

by Apantac (the “Product,”) will be free from defects in material and workmanship for a period of one (1) year from

the date of shipment of the Product to the purchaser.

If the Product proves to be defective during the one (1) year warranty period, the purchaser’s exclusive remedy and

Apantac’s sole obligation under this warranty is expressly limited, at Apantac’s sole option, to:

a) repair the defective Product without charge for parts and labor or,

b) provide a replacement in exchange for the defective Product or,

c) if after a reasonable time, is unable to correct the defect or provide a replacement Product in good working or-

der, then the purchaser shall be entitled to recover damages subject to the limitation of liability set forth below.

Limitation of Liability

Apantac’s liability under this warranty shall not exceed the purchase price paid for the defective product. In no event

shall Apantac be liable for any incidental, special or consequential damages, including without limitation, loss of prof-

its for any breach of this warranty.

If Apantac replaces the defective Product with a replacement Product as provided under the terms of this Warranty,

in no event will the term of the warranty on the replacement Product exceed the number of months remaining on

the warranty covering the defective Product.

Equipment manufactured by other suppliers and supplied by Apantac carries the respective manufacturer’s warranty.

Apantac assumes no warranty responsibility either expressed or implied for equipment manufactured by others and

supplied by Apantac.

This hardware warranty shall not apply to any defect, failure or damage:

a) Caused by improper use of the Product or inadequate maintenance and care of the Product;

b) Resulting from attempts by those other than Apantac representatives to install, repair, or service the Product;

c) Caused by installation of the Product in a hostile operating environment or connection of the Product to incom-

patible equipment;

Apantac W-2×2-H APANTAC Mt Hood FHD Video Wall Controller User manual

Brand: Apantac

Model: W-2×2-H APANTAC Mt Hood FHD Video Wall Controller

Category: Video splitters

Type: User manual

Download PDF

report

Apantac W-2×2-H APANTAC Mt Hood FHD Video Wall Controller User manual

Apantac W-2×2-H APANTAC Mt Hood FHD Video Wall Controller User manual

Related papers

Other documents