Page is loading ...
IMAGING SOLUTIONS INC.
Original Equipment Manufacturer
Installation Instructions for
Door Jamb Cameras
20K152-F / 20K142-F
Prior to Using This Document: Videology reserves the right to modify the information in this
document as necessary and without notice. It is the user’s responsibility to be certain they possess the
most recent version of this document by going to www.videologyinc.com
, searching for the model
number, and comparing revision letters on the respective document, located in the document’s footer.
For technical assistance with this product, please contact the supplier from whom the product was
purchased.
Videology Imaging Solutions, Inc. USA Videology Imaging Solutions, B.V. Europe
37M Lark Industrial Parkway
Greenville, RI 02828
Tel: 401-949-5332
Fax: 401-949-5276
www.videologyinc.com
Neutronenlaan 4
NL-5405 NH Uden, Netherlands
Tel: +31 (0) 413-256261
Fax: +31 (0) 413-251712
www.videology.nl
Doc # INS-20K1X2-F Issue Date: 03/17/2011
Revision: A Page 1 of 6
Table Of Contents
1.
Document History .................................................................................................................2
2. Features:.............................................................................................................................2
3. Dimensions ..........................................................................................................................2
4. Installation:..........................................................................................................................3
5. Camera Connections..............................................................................................................4
6. Specifications .......................................................................................................................4
7. Important Safety Instructions .................................................................................................5
8. Important Safeguards:...........................................................................................................5
9. Contact Information ..............................................................................................................6
1. Document History
Revision Issue
Date Reason CN#
Rev A 03-17-2011 Initial release 11-0031
2. Features:
Resolution Choice of either 520 or 400 TVL
48 Wide Angle 5.5mm lens
Standard BNC/ Power Pin connections
Available in Stainless Steel & OEM options
Power requirement 5 VDC @ 0.8 Watts (Power supply not included)
3. Dimensions
Doc # INS-20K1X2-F Issue Date: 03/17/2011
Revision: A Page 2 of 6
4. Installation:
An installation template is provided to assist in the installation of the mullion camera. (70V0850)
Note: Mullion depth must be a minimum of 1.75” so the unit can operate without interference.
1. Locate a spot at 5 1/2 feet AFF (above finished floor). Attach the enclosed template (70V0850) to
the mullion with the center of the cutout at this spot.
2. Using a #36 drill (0.11”), drill the two mounting holes (if needed) and the two faceplate holes for
the camera.
3. Using a Dremel tool cut-out the center of the template.
4. Using a rat-tail file de-burr and touch up the edges of the rectangular hole. Run the power and
video cables down the inside of the mullion.
5. If using
a 24VAC to 5VDC connector (60BIP5), make sure all electrical connections are protected
from shorting to the metal frame of the door.
(It is recommended that the conversion from 24VAC to 5VDC be done outside of the mullion
casing.)
6. Attach the cables to the camera.
Note: Cables
for the 20K152-F are routed out of the bottom of the camera.
Cables for the 20K142-F are routed out of the top of the camera.
7. C
arefully, insert the camera into the mullion.
Using the 2 mount holes, fasten the
camera to the mullion.
8. Power up the camera and check the image.
Use the adjustment lever on the rear of the
camera to shift the field of view right or
left as needed.
Once field of view is acceptable, mount the
camera and attach cover plate.
20K142-F shown
Doc # INS-20K1X2-F Issue Date: 03/17/2011
Revision: A Page 3 of 6
Doc # INS-20K1X2-F Issue Date: 03/17/2011
Revision: A Page 4 of 6
5. Camera Connections
Video Output BNC connectors used to connect the camera to a monitor or digital video recording system.
Power Input DC 5V input (Power supply not included)
6. Specifications
Electrical
20K152-F
High Resolution
20K142-F
Standard Resolution
Image Sensor 1/4” IL CCD
Resolution 520 TVL 400 TVL
Sensitivity < 0.5 lux < 0.25 lux
Signal to Noise Ratio 50 dB (AGC off)
Video Output Composite 1Vp-p CVBS (75 ohms)
Power supply * 5VDC ±5%
* CAUTION Not polarity protected at board level.
Using the supplied connector mitigates this risk of flying leads
Power consumption < 0.8W
Mechanical
Dimensions W x H x D 39mm x 112mm x 41mm (1.5” x 4.4” x 1.6”)
Weight (w/cable) 95.5g (3.37oz)
Lens 3.7mm F2.0 fi xed pinhole cone
Accessories
Cover plate (brushed stainless) Included
2.1mm power jack & shielded BNC video cable
60PBIP5 24VAC to 5VDC adapter Not Included
60P5VDC 5VDC power supply
Environmental
Operating Temperature -15°C ~ 55°C (5°F ~ 131°F)
Operating Humidity 20 up to 93%RH
Storage Temperature -25°C ~ 70°C (-13°F ~ 158°F)
Storage Humidity Up to 98%RH
Lifetime MTBF > 150000 hrs
Packaging ESD safe package
7. Important Safety Instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock, do not open covers.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
Thi
s symbol is intended to alert the user to the presence of un-insulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
Sa
fety:
Should any liquid or solid object fall into
the camera, unplug the unit and have it
checked by qualified personnel before
operating it any further.
Installation:
Do not install the unit in an extremely hot or humid
place.
The unit is not designed to be waterproof.
Exposure to rain or water may damage
the unit.
Horizontal linearity controls located at the rear
panel are for special adjustments by qualified
personnel only
Cleaning:
Clean the unit with a slightly damp soft
cloth. Use a mild household detergent.
Never use strong solvents such as thinner
or benzene as they might damage the
finish of the unit.
Retain the original carton and packing materials for
safe transport of this unit in the future.
8. Important Safeguards:
1. Carefully read and follow instructions.
2. Do not use this apparatus near water.
3. Clean the unit with a slightly damp soft cloth. Use a mild household detergent.
4. Install in accordance with the manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6. If using a 60P5VDC power supply, make sure the power supply is securely attached to the
receptacle.
Doc # INS-20K1X2-F Issue Date: 03/17/2011
7. Protect the power
cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Revision: A Page 5 of
6
Doc # INS-20K1X2-F Issue Date: 03/17/2011
Revision: A Page 6 of 6
8. Only use attachments/accessories specified by the manufacturer.
9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
10. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
11. Do NOT use power source other than that specified.
12. Use only Class 2 power source or adapter provided by manufacturer.
9. Contact Information
For technical assistance with this product, please contact the supplier from whom the product
was purchased.
For OEM inquiries, contact Videology Imaging Solutions:
North / South America:
Europe:
Videology Imaging Solutions Inc.
37M Lark Industrial Parkway
Greenville, RI 02828
USA
Tel: (401) 949-5332
Fax: (401) 949-5276
Videology Imaging Solutions Europe
Neutronenlaan 4
NL-5405 NH Uden,
Netherlands
Tel: +31 (0) 413 256 261
Fax: +31 (0) 413 251 712
Please visit our website at: http://www.videologyinc.com
VIDEOLOGY IMAGING SOLUTIONS is an ISO 9001 registered video camera developer and
manufacturer serving industrial, machine vision, biometric, security, and specialty OEM markets.
Videology designs, develops, manufactures, and distributes video, image acquisition, and display
technologies and products to OEMs worldwide.
/
