Paradyne 3100 Installation guide

Brand
Paradyne
Model
3100
Type
Installation guide

Paradyne 3100 is a SNMP LAN Adapter Bracket that can be attached to the interior of a standard equipment cabinet or to any flat surface, and holds the LAN Adapter. It allows you to connect all cables to the LAN Adapter and provides two mounting options: using screws and nuts to fasten the bracket to a horizontal rail inside the cabinet or using double-sided foam adhesive tape to fasten it to any clean, flat surface. The bracket also includes a retainer that firmly holds the LAN Adapter in place.

Paradyne 3100 is a SNMP LAN Adapter Bracket that can be attached to the interior of a standard equipment cabinet or to any flat surface, and holds the LAN Adapter. It allows you to connect all cables to the LAN Adapter and provides two mounting options: using screws and nuts to fasten the bracket to a horizontal rail inside the cabinet or using double-sided foam adhesive tape to fasten it to any clean, flat surface. The bracket also includes a retainer that firmly holds the LAN Adapter in place.

13100-A2-GN11-00 October 1997
SNMP LAN Adapter Bracket
Installation Instructions
Document Number 3100-A2-GN11-00
October 1997
SNMP LAN Adapter Bracket Installation
The SNMP LAN Adapter Bracket can be attached to the interior of a standard equipment cabinet or to any flat
surface, and holds the LAN Adapter. Referring to the illustration on the next page, follow these steps to install the
bracket:
1. Record the Media Access Control (MAC) address, marked “LAN Address,” from the label on the bottom
of the LAN Adapter. The label is not visible when the LAN Adapter is mounted in the bracket.
2. Connect all cables to the LAN Adapter according to the instructions that came with it. (Cables can be
attached after the bracket is mounted, but accessibility to the LAN Adapter back panel may be less
convenient.)
3. Determine how the LAN Adapter will be oriented in the bracket. It can be mounted in the bracket with the
front of the LAN Adapter facing left or right. See the illustration on the next page.
4. Slide the LAN Adapter into the bracket. The two tabs along the edge of the bracket fit into the recess in
the back of the LAN Adapter.
5. Using the small screw provided, attach the retainer loosely to the side of the bracket that the front of the
LAN Adapter is facing.
6. Position the retainer so that it firmly holds the LAN Adapter in place, and tighten the retainer screw.
7. Fasten the bracket in place:
• If you are installing the bracket in a cabinet, use the two screws and two nuts to fasten the bracket to a
horizontal rail inside the cabinet. Do not block access to cable connectors and other equipment inside
the cabinet.
• If you are installing the bracket in an environment with no cabinet or available screw rails, use
double-sided foam adhesive tape on the back of the bracket to fasten it to any clean, flat surface.
Remove the protective film from the adhesive. Position the bracket squarely where you want it to be,
then press down on it firmly for several seconds.
TM
All manuals and user guides at all-guides.com
all-guides.com
2
October 1997 3100-A2-GN11-00
PARALLEL PRINTER
UNIPORT
ETHERNET NETWORK
10BaseT
Thinnet
Port 1
POWER
PARALLEL PRINTER
UNIPORT
ETHERNET NETWORK
10BaseT
Thinnet
Port 1
POWER
97-15705
PARALLEL PRINTER
UNIPORT
ETHERNET NETWORK
10BaseT
Thinnet
Port 1
POWER
LAN
Adapter
(Front)
Retainer
(Front Left)
Bracket
Retainer
(Front Right)
PARALLEL PRINTER
UNIPORT
ETHERNET NETWORK
10BaseT
Thinnet
Port 1
POWER
LAN
Adapter
(Front)
PARALLEL PRINTER
UNIPORT
ETHERNET NETWORK
10BaseT
Thinnet
Port 1
POWER
LAN
Adapter
(Front)
LAN Adapter Bracket Installation

*3100–A2–GN11–00*
All manuals and user guides at all-guides.com
  • Page 1 1
  • Page 2 2

Paradyne 3100 Installation guide

Brand
Paradyne
Model
3100
Type
Installation guide

Paradyne 3100 is a SNMP LAN Adapter Bracket that can be attached to the interior of a standard equipment cabinet or to any flat surface, and holds the LAN Adapter. It allows you to connect all cables to the LAN Adapter and provides two mounting options: using screws and nuts to fasten the bracket to a horizontal rail inside the cabinet or using double-sided foam adhesive tape to fasten it to any clean, flat surface. The bracket also includes a retainer that firmly holds the LAN Adapter in place.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents