Paradyne HotWire 8800 DSLAM Installation guide

Brand: Paradyne

Model: HotWire 8800 DSLAM

Category: Networking

Type: Installation guide

This manual is also suitable for

HotWire 8800

HOTWIRE 8800

DIGITAL SUBSCRIBER LINE

ACCESS MULTIPLEXER

(DSLAM)

INSTALLATION GUIDE

Document No. 8800-A2-GN21-20

October 1997

Printed on recycled paper

8800-A2-GN21-20

October 1997

Printed in U.S.A.

Notice

This publication is protected by federal copyright law. No part of this publication may be copied or distributed,

transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form

or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the

express written permission of Paradyne Corporation, 8545 126th Avenue North, P.O. Box 2826, Largo,

Florida 33779-2826.

Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation

reserves the right to revise this publication and to make changes from time to time in the contents hereof without

obligation of Paradyne Corporation to notify any person of such revision or changes.

Changes and enhancements to the product and to the information herein will be documented and issued as a new

release to this manual.

Warranty, Sales, and Service Information

Contact your sales or service representative directly for any help needed. For additional information concerning

warranty, sales, service, repair, installation, documentation, or training, use one of the following methods:

H Via the Internet: Visit the Paradyne World Wide Web site at http://www.paradyne.com

H Via Telephone: Call our automated call system to receive current information via fax or to speak with a

company representative.

— Within the U.S.A., call 1-800-870-2221

— International, call 813-530-2340

Trademarks

All products and services mentioned herein are the trademarks, service marks, registered trademarks or registered

service marks of their respective owners.

Important Regulatory Information

8800-A2-GN21-20 October 1997

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or included in the manual.

2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to

protect it from overheating, these slots and openings must not be blocked or covered.

3. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous

high voltage points or other risks. Refer all servicing to qualified service personnel.

4. General purpose cables are provided with this product. Special cables, which may be required by the regulatory

inspection authority for the installation site, are the responsibility of the customer.

5. When installed in the final configuration, the product must comply with the applicable Safety Standards and

regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory

agencies and inspection authorities to ensure compliance.

6. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If

products installed in separate buildings are interconnected, the voltage potential may cause a hazardous

condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if

necessary, implement corrective action prior to interconnecting the products.

7. Connect the product to a 48 Vdc SELV supply source that is electrically isolated from the ac source. The 48 Vdc

source is to be reliably connected to earth. Connect the earthing (grounding) wire to the protective earthing

(grounding) lug connector, identified by the protective earth symbol.

8. A readily accessible disconnect device as part of the building installation shall be incorporated in fixed wiring. The

disconnect device (a 48 Vdc, 15 or 20A circuit breaker or switch) must be included in the ungrounded supply

conductor. Over current protection must be 15 or 20A, 48 Vdc fuse or circuit breaker.

9. If the equipment is to be compliant with the Bellcore NEBS requirements GR–1089–CORE, sections 4.2.2

(Current Limiting Protectors) and 4.5.11 (Current Limiting Protector Tests), current limiting protectors shall be

used on the DSL lines entering the facility.

10. This product is to be installed only in a Restricted Access Location (dedicated equipment rooms, equipment

closets or the like) in accordance with articles 110-16, 110-17 and 110-18 of the National Electrical Code,

ANSI/NFPA 70.

11. In addition, if the equipment is to be used with telecommunications circuits, take the following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the

network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of

electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

Important Regulatory Information

8800-A2-GN21-20

October 1997

EMI Warnings

WARNING:

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the requirements that no modifications will be

made to the equipment unless the changes or modifications are expressly approved by Paradyne

Corporation.

WARNING:

To Users of Digital Apparatus in Canada:

This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment

regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du règlement sur le matérial

brouilleur du Canada.

Notice to Users of the Canadian Telephone Network

The Industry Canada label identifies certified equipment. This certification means that the equipment meets

telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal

Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to

the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of connection. The

customer should be aware that compliance with the above conditions may not prevent degradation of service in some

situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or

alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines

and internal metallic water pipe system, if present, are connected together. This precaution may be particularly

important in rural areas.

CAUTION:

Users should not attempt to make such connections themselves, but should contact the appropriate electric

inspection authority, or electrician, as appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum

number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of

any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the

devices does not exceed 5.

Important Regulatory Information

8800-A2-GN21-20 October 1997

CE Marking

When the product is marked with the CE mark, this demonstrates full compliance with the following European

Directives:

— Directive 72/73/EEC – Council Directive of 19 February 1973 on the harmonization of the laws of the member

states relating to electrical equipment designed for use within certain voltage limits, as amended by Directive

93/68EEC.

— Directive 89/336/EEC – Council Directive of 3 May 1989 on the approximation of the laws of the member

states relating to Electro-Magnetic Compatibility (EMC), as amended by Directive 93/68/EEC.

Japan

Class 1 ITE

This is a Class 1 product based on the standard of the Voluntary Control Council for interference by Information

Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise.

When such trouble occurs, the user may be required to take corrective actions.

8800-A2-GN21-20

October 1997

Contents

About This Guide

 Document Purpose and Intended Audience iii. . . . . . . . . . . . . . . . . . . . . . . . .

 Document Summary iv. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Product-Related Documents v. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1 About the HotWire 8800 DSLAM

 What is the HotWire 8800 DSLAM? 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 HotWire 8800 DSLAM Components 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 HotWire 8800 DSLAM Features 1-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Network Equipment Building Standards (NEBS) 1-4. . . . . . . . . . . . . . . . .

 Mounting Configurations 1-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 Installing and Connecting the Hardware

 Overview 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Package Contents 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Unpacking the Hardware 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Pre-installation Considerations 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Installation Tasks 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Chassis Installation 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation into a 19-Inch Rack 2-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation into a 23-Inch Rack 2-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the Chassis Set Back 3 or 5 Inches 2-9. . . . . . . . . . . . . . . . . . . .

Installation into a Rack without Threaded Screw Holes 2-10. . . . . . . . . . .

High Density Back-to-Back Installations 2-11. . . . . . . . . . . . . . . . . . . . . . . .

 Installing the Optional Air Filter 2-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Supplying Power 2-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Installing the MCC Card 2-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Installing DSL Cards 2-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Verifying the Installation 2-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents

8800-A2-GN21-20

October 1997

 Making Cable Connections 2-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Special Connection Considerations 2-19. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting to a POTS Splitter or an MDF 2-19. . . . . . . . . . . . . . . . . . . . . .

Connecting CO Alarm to the Alarm System 2-21. . . . . . . . . . . . . . . . . . . . .

Connecting Ethernet Connections to the Ethernet Hubs or

Switches 2-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting to an SNMP Management System or to a Remote

Workstation Using Terminal Type vt100 2-23. . . . . . . . . . . . . . . . . . . . . . . . .

Connecting to a Terminal or Laptop Computer 2-24. . . . . . . . . . . . . . . . . . .

Connecting to a Modem for Remote Management 2-25. . . . . . . . . . . . . . .

3 Initial Setup Instructions

 Setting the IP Address and Subnet Mask on the MCC for Remote

Configuration 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 Troubleshooting

 Power Failure Troubleshooting Procedures 4-1. . . . . . . . . . . . . . . . . . . . . . . . .

 Additional Troubleshooting Procedures 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . .

A LEDs

 Overview A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 HotWire 8800 DSL Access System Chassis A-1. . . . . . . . . . . . . . . . . . . . . . . .

 MCC Card A-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B Pinouts

 8-Pin Modular LAN/WAN Connector and Management 10BaseT

Connector Pinouts B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 8-Pin Modular Management Serial Connector Pinouts B-2. . . . . . . . . . . . . . .

 6-Pin Modular Alarm Connector Pinouts B-2. . . . . . . . . . . . . . . . . . . . . . . . . . . .

 Telco 50-pin Connector Pinouts for DSL Loops and POTS Splitters B-3. . . .

 DB25 Adapter Pinouts B-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C Technical Specifications

Glossary

Index

iii

8800-A2-GN21-20

October 1997

About This Guide

Document Purpose and Intended Audience

This guide describes how to:

 Mount the HotWire 8800 Digital Subscriber Line Access Multiplexer (DSLAM)

chassis at the Central Office (CO) or Internet Service Provider (ISP) location

adjacent to the CO.

 Install the Management Communications Controller (MCC) and Digital

Subscriber Line (DSL) cards into the chassis.

 Connect cables to the primary data and network management system LANs,

to a console, modem (for remote terminal access), to the local loops, and to a

CO alarm system.

It is written for administrators and technicians who install devices at the Central

Office. It should be used in conjunction with the

HotWire DSLAM for 8540 and

8546 DSL Cards Network Configuration Guide

, which describes how to plan the

data networks surrounding the DSLAM, and with the

HotWire DSLAM for 8540

and 8546 DSL Cards User’s Guide

which describes how to configure and operate

the DSLAM DSL and MCC cards.

The chassis requires one MCC card and at least one DSL card, which must be

ordered separately. It is assumed that you have already purchased the required

circuit cards.

To install the Customer Premises (CP) portion of the HotWire 8800 DSLAM, refer

to the appropriate HotWire Remote Termination Unit (RTU) Customer Premises

Installation Instructions and HotWire POTS Splitter Customer Premises

Installation Instruction

About This Guide

8800-A2-GN21-20

October 1997

Document Summary

Section Description

Chapter 1

About the HotWire 8800 DSLAM.

Provides an overview

of the DSLAM chassis, its features, and requirements.

Chapter 2

Installing and Connecting the Hardware.

Describes

how to mount the chassis, install the MCC and DSL

cards, and make cable connections to the network.

Chapter 3

Initial Setup Instructions.

Describes how to assign an

IP address to the MCC card to allow for remote

configuration.

Chapter 4

Troubleshooting.

Describes troubleshooting procedures

for common problems.

Appendix A

LEDs.

Describes the meaning of the LEDs on the

chassis, the MCC card, and DSL cards.

Appendix B

Pinouts.

Provides the pin assignments for the

connectors on the Interface Panel.

Appendix C

Technical Specifications.

Provides the technical

specifications of the chassis.

Glossary Defines acronyms and terms used in this document.

Index Lists key terms, acronyms, concepts, and sections in

alphabetical order.

About This Guide

8800-A2-GN21-20

October 1997

Product-Related Documents

Document Number Document Title

5020-A2-GN10

HotWire POTS Splitter Central Office Installation

Instructions

5030-A2-GN10

HotWire 5030 POTS Splitter Customer Premises

Installation Instructions

5034-A2-GN10

HotWire 5034 Indoor POTS Splitter Installation

Instructions

5216-A2-GN10

HotWire 5216 Remote Termination Unit (RTU)

Installation Instructions

5246-A2-GN10

HotWire 5246 Remote Termination Unit (RTU)

Installation Instructions

5446-A2-GN10

HotWire 5446 Remote Termination Unit (RTU)

Customer Premises Installation Instructions

8000-A2-GB20

HotWire DSLAM for 8540 and 8546 DSL Cards

User’s Guide

8000-A2-GB21

HotWire DSLAM for 8540 and 8546 DSL Cards

Network Configuration Guide

8000-A2-GB24

HotWire DSLAM Configuration for 8540 and 8546

DSL Cards Startup Guide

8000-A2-GB90

HotWire 8100/8200 Internetworking Packet

Concentrator (IPC) User’s Guide

8000-A2-GN11

HotWire Management Communications Controller

(MCC) Card Installation Instructions

8000-A2-GU10

Special Notice RADSL Connection Considerations

8540-A2-GN10

HotWire 8546 Digital Subscriber Line (DSL) Card

Installation Instructions

8546-A2-GN10

HotWire 8546 Digital Subscriber Line (DSL) Card

Installation Instructions

8800-A2-GN10

Replacement Air Filter for the HotWire 8800 DSLAM

Installation Instructions

Contact your sales representative to order additional product documentation.

1-1

8800-A2-GN21-20

October 1997

About the HotWire 8800

DSLAM

What is the HotWire 8800 DSLAM?

The HotWire 8800 Digital Subscriber Line Access Multiplexer (DSLAM), which

can be installed in the Central Office (CO) or at an Internet Service Provider (ISP)

location adjacent to the CO, provides high-speed Internet or Intranet access.

Through the use of Digital Subscriber Line (DSL) technology, the DSLAM

provides simultaneous high-speed data access (digital) and POTS service

(analog) over the same twisted-pair telephone line. Support of this simultaneous

access requires the installation of POTS splitters at both ends of the line (i.e., at

the CO and at the customer premises (CP)).

When used in combination with a HotWire 8200 Interworking Packet

Concentrator (IPC), the HotWire 8800 DSLAM provides high-speed IP service

concentration over a wide array of LAN architectures as well as ATM interfaces to

Wide Area Networks.

About the HotWire 8800 DSLAM

1-2

8800-A2-GN21-20

October 1997

The following illustration shows a high-level view of a HotWire configuration:

NOTE:

You may make cable connections from a DSL card directly to a Main

Distribution Frame (MDF) or through a POTS splitter to an MDF but not both.

Legend: DSL - Digital Subscriber Line RTU - Remote Termination Unit

MDF - Main Distribution Frame POTS - Plain Old Telephone Service

IPC - Interworking Packet Concentrator

* Optional

DSL

CARD

DSLAM

Central Office (CO)

97-15674-01

Customer Premises (CP)

Switch

Ethernet

RTU

*CP

POTS

Splitter

*CO

POTS

Splitter

MDF

POTS/DSL

HotWire

8200

IPC

Voice

Interface

Data

Interface

POTS

Network

Service

Provider

The HotWire 8800 DSLAM can be configured to operate with multiple types of

Remote Termination Units (RTU) installed at the customer end of the telephone

loop to allow users at remote locations access to Internet Service Providers or

corporate networks by means of the DSLAM. For more information regarding

which DSL cards interoperate with which RTUs, see your Paradyne sales

representative

About the HotWire 8800 DSLAM

1-3

8800-A2-GN21-20

October 1997

HotWire 8800 DSLAM Components

The HotWire 8800 DSLAM system consists of the following components:

 HotWire 8800 DSLAM chassis

HotWire 8800 is a 20-slot chassis with integral power, alarm, cooling, and

interface subsystems designed to house up to 18 DSL cards and one

Management Communications Controller (MCC) card. (The remaining slot is

reserved for future use.)

 One Management Communications Controller (MCC) card

The chassis requires one MCC card, which is a processor card that

administers and provides diagnostic connectivity to the DSL cards. It acts as

a mid-level manager and works in conjunction with an SNMP network

management system, such as HP OpenView, via its LAN port. It gathers

operational status for each of the DSL cards and responds to the SNMP

requests. It also has a serial port for local terminal access.

 At least one Digital Subscriber Line (DSL) card

The chassis requires at least one DSL card, which is a circuit card that

contains four DSL ports, an Ethernet interface to the NSP, and a processor.

The processor controls the modems and forwards the packet traffic to and

from the Ethernet and DSL interfaces. When the chassis is fully populated, it

provides a total of 72 DSL ports.

NOTE:

You must order the MCC and DSL cards separately. They are not provided

with the chassis.

ALARMS

Major MinorFanBA

POWER

MCC

SYSTEM

Alm

Test

ETHERNET

Coll

97-15280

MGT

SERIAL

MGT

10BT

ALARM

SLOTS 1 - 6

SLOTS 7-12

SLOTS 13-18

LINES

-48V (A)

-48V INPUT

-48V (B)

RET (A)

RET (B)

FR GND

13 15

LAN/WAN SLOT

RADSL

SYSTEM

Alm

Test

ETHERNET

Coll

DSL PORT

SLOTS 13-18

About the HotWire 8800 DSLAM

1-4

8800-A2-GN21-20

October 1997

HotWire 8800 DSLAM Features

The HotWire 8800 DSLAM system has the following features:

 Power Redundancy and Load Sharing

The chassis provides a power input terminal block, which is capable of

accepting two independent –48 Vdc power inputs. Two power sources can

be connected to the chassis to provide power redundancy and load sharing.

If one power source fails, the other source provides all of the power needed

by the system. This is done automatically without system disruption.

The chassis distributes –48 Vdc power from the CO power source to

individual cards via the interface module and the backplane.

 A Convenient Front-Facing Interface Panel

The interface panel on the chassis allows all interface cables to be connected

and maintained in the front of the chassis for easy accessibility.

 Major/Minor Alarm Contacts for CO Alarm Requirements

The interface panel provides two sets of dry contacts on a 6-pin jack interface

for connection to a Central Office (CO) alarm system.

 LED Monitors for Power and Fan Status and Major and Minor Alarms

LEDs on the front panel of the HotWire 8800 chassis are indicators of the

status of chassis functioning. For more information on the meaning of LED

indications, see Appendix A,

LEDs

 Hot Swappable Cards

The MCC and DSL cards can be installed and removed from the chassis

without service disruption to other cards.

Network Equipment Building Standards (NEBS)

The 8800 DSLAM meets Network Equipment Building Standards (NEBS) Level 2

Criteria. In addition, it meets NEBS Level 3 Earthquake (Zone 4 Level).

Refer to NEBS Heat Release Limits to determine the number of chassis that can

be mounted in a rack. Up to three HotWire 8800 DSLAMs may be mounted in a

7-foot rack and comply with NEBS Floor Heating Load Limits.

About the HotWire 8800 DSLAM

1-5

8800-A2-GN21-20

October 1997

Mounting Configurations

The HotWire 8800 DSLAM chassis can be mounted in any commercial Electronic

Industries Association (EIA) standard 19- or 23-inch rack. The 8800 chassis uses

forced-convection cooling. Maximum power dissipation is less than 400 watts for

a fully-loaded chassis. Up to four fully loaded chassis can be mounted in a 7-foot

rack, providing 288 modem ports.

The following figures depict several examples of chassis mounting configurations:

 Four chassis in a rack

 Two chassis and two six-slot POTS splitters in a rack, and

 Four chassis and four six-slot POTS splitters in adjacent racks.

NOTE:

In this guide, the term

rack

refers to a CO rack, cabinet, frame, or bay.

97-15281-0

ALARMS

Major MinorFanBA

POWER

ALARMS

Major MinorFanBA

POWER

ALARMS

Major MinorFanBA

POWER

ALARMS

Major MinorFanBA

POWER

Four HotWire 8800 DSLAMS

in a Rack

97-15426-01

ALARMS

MajorMinorFanBA

POWER

ALARMS

MajorMinorFanBA

POWER

8800

DSLAM

Chassis

Six-Card

POTS

Splitter

Chassis

19" Cabinet

Two HotWire 8800 DSLAMS

and Two Six-Slot POTs Splitter

in a Rack

About the HotWire 8800 DSLAM

1-6

8800-A2-GN21-20

October 1997

97-15427-0

ALARMS

Major MinorFanBA

POWER

ALARMS

Major MinorFanBA

POWER

ALARMS

Major MinorFanBA

POWER

ALARMS

Major MinorFanBA

POWER

Four HotWire 8800 DSLAMS and Four Six-Slot

POTs Splitter in Adjacent Racks

The 8800 chassis can be mounted in a back-to-back configuration (up to

8 chassis in a 7-foot rack) to provide up to 576 DSL ports requiring no more than

a 24-inch depth.

97-15340

For more information about mounting configurations, see Chapter 2,

Installing

and Connecting the Hardware

2-1

8800-A2-GN21-20

October 1997

Installing and Connecting

the Hardware

Overview

The HotWire 8800 DSLAM chassis, which houses MCC and DSL cards, can be

mounted in any commercial EIA-standard 19- or 23-inch rack.

This chapter provides instructions for:

 Mounting the HotWire 8800 DSLAM chassis into a rack

 Installing the optional air filter

 Supplying power

 Installing the MCC card and DSL card(s) into the chassis

 Connecting to a POTS splitter shelf or Main Distributing Frame (MDF)

 Connecting to the CO alarm system

 Connecting to the Ethernet hubs or switches

 Connecting to a console terminal, laptop computer, or modem

NOTE:

The term

rack

refers to a CO rack, cabinet, frame, or bay.

Package Contents

The HotWire 8800 DSLAM chassis consists of the following components (all of

which are already installed in the chassis):

 1 Chassis with backplane

 1 Interface Module (with a front-facing Interface Panel)

 1 Fan module

 20 Filler plates

Installing and Connecting the Hardware

2-2

8800-A2-GN21-20

October 1997

NOTE:

The HotWire 8800 DSLAM requires an MCC card and at least one DSL card

for proper functionality. These cards are not provided with this product and

must be ordered separately.

ALARMS

Major MinorFanBA

POWER

97-15280a

MGT

SERIAL

MGT

10BT

ALARM

SLOTS 1 - 6

SLOTS 7-12

SLOTS 13-18

LINES

-48V (A)

-48V INPUT

-48V (B)

RET (A)

RET (B)

FR GND

13 15

LAN/WAN SLOT

Filler Plates

MCC Card

DSL Card

Fan

Module

Interface

Panel

MCC

SYSTEM

Alm

Test

ETHERNET

Coll

RADSL

SYSTEM

Alm

Test

ETHERNET

Coll

DSL PORT

In addition, each chassis is shipped with the following:

 Associated hardware bundled in a plastic bag:

— Three cable ties

— Three shorter 50-pin Telco connector captive screws

(to replace longer Telco captive screws)

— Four #10-32 mounting screws

— Four #12-24 mounting screws and four #12-24 speed nuts

(for use with racks without threaded mounting holes)

 Air filter, which can be installed in the chassis if required.

 Documentation:

— This guide, the

HotWire Digital Subscriber Line Access Multiplexer

(DSLAM) Installation Guide

You can access the next two documents on the Paradyne World Wide

Web site at http://www.paradyne.com, under Service and Support.

—

HotWire DSLAM for 8540 and 8546 DSL Cards User’s Guide

—

HotWire DSLAM for 8540 and 8546 DSL Cards Network Configuration

Guide

Installing and Connecting the Hardware

2-3

8800-A2-GN21-20

October 1997

Unpacking the Hardware

When shipped, the HotWire 8800 DSLAM chassis is packed in a cardboard

shipping container. Carefully remove the chassis from its shipping container and

check for physical damage. If the chassis shows signs of shipping damage, report

this immediately to your shipping and sales representatives.

Pre-installation Considerations

Consider the following before performing the chassis installation:

 Installation Site

Your installation site should be well-ventilated, clean, and free of

environmental extremes. There should be 2 to 3 feet of clearance at the front

of the rack in which the chassis is to be installed to allow access for the

installation of the chassis, circuit cards, and cables.

 Power

The HotWire 8800 DSLAM operates from a standard CO –48 Vdc power

supply (–40.0 to –60.0 Vdc). The power source wires must be between

10 AWG and 16 AWG, and can be either solid or stranded. However, the

preferred power source wire type is 14 AWG stranded.

 Grounding

A copper lug connector is attached to the chassis grounding post. It can

accept a bare wire, 6 through 14 AWG.

 Cabling

The following customer-provided cables and cable adapters are required with

this product:

— Telco 50-pin cable for connection to the CO POTS splitter shelf or MDF.

You will need one 50-pin cable for Slots 1 – 6, one 50-pin cable for

Slots 7 – 12, and one 50-pin cable for Slots 13 – 18.

— 6-pin modular cable for connection to a CO alarm system, if required.

— 8-pin UTP (Unshielded Twisted Pair) CAT5 modular cable for connection

to the DSL 10BaseT Ethernet ports. You will need a cable for each card

in the DSLAM.

— 8-pin UTP CAT5 modular cable for connection to management domain

LAN for SNMP management system or telnet access.

— A CAT5 serial cable and DB25 (male) adapter are shipped with the MCC

card. However, for connection to a terminal or computer, you may have to

supply a (female) DB9 to (male) DB25 adapter if your terminal or

computer has a 9-pin serial port. For connection to a modem, you may

need to supply a null modem adapter.

Installing and Connecting the Hardware

2-4

8800-A2-GN21-20

October 1997

CAUTION:

Use of any non-twisted pair wiring arrangements, such as jumpers, can

cause reduction in overall DSL reach performance, even over short

distances. Please refer to the Special Notice shipped with this product.

Pin assignments are included in Appendix B,

Pinouts

NOTE:

The HotWire 8800 DSLAM chassis weighs approximately 30 pounds and can

be easily installed by one installer.

Installation Tasks

The following table lists the tasks you need to perform to install and connect the

HotWire 8800 DSLAM.

Task

See

1. Mount the chassis into a standard

19- or 23-inch rack.

Chassis Installation

, page 2-5

2. Supply power and ground to the

chassis.

Supplying Power

, page 2-13

3. Install the MCC card into the chassis

(Slot 19).

Installing the MCC Card

, page 2-15

4. Install DSL cards into the chassis

(Slot 1–18).

Installing DSL Cards

, page 2-17

5. Verify the hardware installation.

Verifying the Installation

, page 2-18

6. Connect the chassis to a POTS splitter

shelf, MDF, or other demarcation point.

Connecting to a POTS Splitter or an MDF

page 2-19

7. (Optional) Connect the chassis to a CO

alarm system.

Connecting CO Alarm to the Alarm

System

, page 2-21

8. Make Ethernet connections to the

Ethernet hub or switch.

Connecting Ethernet Connections to the

Ethernet Hubs or Switches

, page 2-22

9. Connect to an SNMP management

system.

Connecting to an SNMP Management

System or to a Remote Workstation Using

Terminal Type vt100

, page 2-23

10.Connect to a terminal, laptop computer

(with terminal emulation capability), or

modem.

Connecting to a Terminal or Laptop

Computer

, page 2-24

Page is loading ...

Paradyne HotWire 8800 DSLAM Installation guide

Brand: Paradyne

Model: HotWire 8800 DSLAM

Category: Networking

Type: Installation guide

This manual is also suitable for

HotWire 8800

Download PDF

report

Paradyne HotWire 8800 DSLAM Installation guide

This manual is also suitable for

Paradyne HotWire 8800 DSLAM Installation guide

Related papers

Other documents