Trendnet TPE-5028WS User guide

Category
Network switches
Type
User guide
TRENDnet User’s Guide
Cover Page
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
a
Thank you for purchasing your new TRENDnet PoE
Web Smart Switch!
Please note: The scope of this user's guide encompasses multiple
products with varying features. Images, artwork, and other specificities
including port count, interfaces etc. may not be identical to the model
you purchased. Please consult the specific model specifications for your
unit for a full list of supported features.
Please ensure your switch’s firmware version is V2.10.010 or newer for
Layer 2+ management features. See the Firmware Upgrade section in
this document for additional information regarding the firmware upgrade
procedure.
Contents
PoE Web Smart Switch Series Product Overview .............................. i
TPE-082WS Overview ...................................................................................................... i
Package Contents .................................................................................................. i
TPE-082WS Hardware Features ............................................................................. i
TPE-1620WS v2 & TPE-1620WSF Overview .................................................................... v
Package Contents ................................................................................................. v
TPE-1620WS/TPE-1620WSF Hardware Features .................................................. v
TPE-2840WS v2 Overview ............................................................................................ vii
Package Contents ............................................................................................... vii
TPE-2840WS Hardware Features ........................................................................ vii
TPE-5028WS Overview .................................................................................................. ix
Package Contents ................................................................................................ ix
TPE-5028WS Hardware Features ......................................................................... ix
TPE-5240WS Overview .................................................................................................. xi
Package Contents ................................................................................................ xi
TPE-5240WS Hardware Features ......................................................................... xi
TPE-5048WS Overview ................................................................................................ xiii
Package Contents .............................................................................................. xiii
TPE-5048WS Hardware Features ....................................................................... xiii
Switch Installation .......................................................................... 1
Desktop Hardware Installation ...................................................................................... 1
Rack Mount Hardware Installation ................................................................................ 1
Basic IP Configuration .................................................................................................... 2
Connect additional devices to your switch .................................................................... 5
Accessing switch management interfaces ........................................ 6
Access your switch management page.......................................................................... 6
System Info ...................................................................... Error! Bookmark not defined.
View your switch status information ................................................................... 6
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
b
System ............................................................................................ 8
System Management ..................................................................................................... 9
Set your system information ............................................................................... 9
L3 Feature .................................................................................................................... 10
IPv4 Interface ..................................................................................................... 10
IPv4 ARP Aging Time .......................................................................................... 11
IPv4 Static ARP ................................................................................................... 12
IPv4 Static/Default Route .................................................................................. 12
Set your IPv6 settings ........................................................................................ 13
Add IPv6 neighbors ............................................................................................ 15
Configure IPv6 Routing Table ............................................................................ 16
DNS .............................................................................................................................. 17
Set your DNS server settings.............................................................................. 17
IP Access List ................................................................................................................ 18
Restrict access to switch management page ..................................................... 18
Administration ............................................................................................................. 19
Change administrator password and add accounts........................................... 19
Timeout........................................................................................................................ 20
Change web idle login timeout settings ............................................................ 20
System Time ................................................................................................................ 21
Set the switch date and time ............................................................................. 21
SSL ................................................................................................................................ 22
Enable HTTPS/SSL (Secure Socket Layer) management access ......................... 22
SSH ............................................................................................................................... 23
Enable SSH (Secure Shell) management access ................................................. 23
Telnet ........................................................................................................................... 24
Enable Telnet management access.................................................................... 24
DHCP Auto Configuration ............................................................................................ 25
Enable DHCP Auto Configuration....................................................................... 25
System Log ................................................................................................................... 26
View and setup your switch logging .................................................................. 26
SNMP ........................................................................................................................... 28
Settings .............................................................................................................. 28
View ................................................................................................................... 29
Group ................................................................................................................. 30
User ................................................................................................................... 31
Community ........................................................................................................ 32
Trap .................................................................................................................... 33
RMON .......................................................................................................................... 34
Settings .............................................................................................................. 34
Statistics ............................................................................................................. 35
History ............................................................................................................... 36
Alarms ................................................................................................................ 37
Events ................................................................................................................ 38
Statistics....................................................................................................................... 40
Traffic ................................................................................................................. 40
Error ................................................................................................................... 41
IEEE 802.3az EEE .......................................................................................................... 42
Enable IEEE 802.3az Power Saving Mode .......................................................... 42
Network ....................................................................................... 43
Physical Interface......................................................................................................... 43
Configure Physical Interfaces ............................................................................ 43
Spanning Tree .............................................................................................................. 45
Protocol ............................................................................................................. 45
Port .................................................................................................................... 46
MST .................................................................................................................... 48
Instance ............................................................................................................. 49
MST Port ............................................................................................................ 49
Trunk ............................................................................................................................ 50
Settings .............................................................................................................. 50
Status ................................................................................................................. 51
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
c
Port Priority ....................................................................................................... 51
Mirroring ...................................................................................................................... 52
Configure port mirror settings ........................................................................... 52
Loopback Detection ..................................................................................................... 53
Enable loopback detection ................................................................................ 53
Static Unicast ............................................................................................................... 54
Add static unicast entries to the switch ............................................................. 54
Static Multicast ............................................................................................................ 55
Add static multicast entries to the switch ......................................................... 55
IGMP Snooping ............................................................................................................ 56
Settings .............................................................................................................. 56
Router Ports ....................................................................................................... 57
MLD Snooping .............................................................................................................. 58
Settings .............................................................................................................. 58
Router Port ........................................................................................................ 59
Multicast VLAN ............................................................................................................ 60
Multicast VLAN Settings ..................................................................................... 60
Multicast VLAN Table ......................................................................................... 60
Multicast VLAN Group Settings ......................................................................... 60
Multicast VLAN Access Settings ......................................................................... 61
Multicast Filtering ........................................................................................................ 62
Multicast Filtering .............................................................................................. 62
Bandwidth Control ....................................................................................................... 62
Storm Control .................................................................................................... 62
Ingress Rate Limiting .......................................................................................... 63
Egress Rate Limiting ........................................................................................... 63
VLAN ............................................................................................................................ 64
Tagged ............................................................................................................... 64
Port .................................................................................................................... 65
Forwarding ......................................................................................................... 66
Dynamic ............................................................................................................. 66
Private ................................................................................................................ 67
Current ............................................................................................................... 68
GVRP ............................................................................................................................ 68
GVRP Global Settings ......................................................................................... 68
Port Settings ...................................................................................................... 69
Time Settings ..................................................................................................... 70
Voice VLAN .................................................................................................................. 71
Settings .............................................................................................................. 72
OUI ..................................................................................................................... 73
LLDP ............................................................................................................................. 74
Enable and configure LLDP ................................................................................ 74
Settings .............................................................................................................. 74
Basic TLVs Settings ............................................................................................. 76
Dot1 TLVs Settings ............................................................................................. 76
Dot3 TLVs Settings ............................................................................................. 76
MED Port Settings .............................................................................................. 76
LLDP Statistics Information ................................................................................ 77
LLDP Local Port Information .............................................................................. 77
Neighbor ............................................................................................................ 77
MAC VLAN ................................................................................................................... 78
MAC VLAN ......................................................................................................... 78
Protocol VLAN .............................................................................................................. 78
Protocol VLAN Profile ........................................................................................ 78
Protocol VLAN Profile Interface ......................................................................... 79
QoS (Quality of Service) ................................................................ 80
CoS ............................................................................................................................... 80
Set CoS priority settings ..................................................................................... 80
Port Priority ................................................................................................................. 81
Set Port Priority ................................................................................................. 81
DSCP ............................................................................................................................ 81
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
d
Set DSCP (Differentiated Services Code Point) Class Mapping settings ............ 81
Scheduling Algorithm ................................................................................................... 82
Set the Scheduling Algorithm ............................................................................ 82
IPv6 Traffic Class .......................................................................................................... 83
Configure the IPv6 Traffic Class Settings ........................................................... 83
PoE (Power over Ethernet) ............................................................ 84
Power over Ethernet.................................................................................................... 84
Configure PoE settings ....................................................................................... 85
Time Range .................................................................................................................. 86
Configure PoE Time Range ................................................................................. 86
Security ......................................................................................... 87
Port Access Control ...................................................................................................... 89
Configure Port Access Control ........................................................................... 89
Dial-in User .................................................................................................................. 90
Create Dial-In Users (Local Authentication Method) ......................................... 90
RADIUS ......................................................................................................................... 91
Add RADIUS Servers (RADIUS Authentication Method) .................................... 91
TACACS+ ...................................................................................................................... 92
Add TACACS+ Servers (TACACS+ Authentication Method) ................................ 92
Destination MAC Filter ................................................................................................ 93
Destination MAC Filter ....................................................................................... 93
Denial of Service .......................................................................................................... 94
Denial of Service (DoS) ....................................................................................... 94
DHCP Snooping ............................................................................................................ 95
Settings .............................................................................................................. 95
VLAN .................................................................................................................. 97
Interfaces ........................................................................................................... 98
Binding ............................................................................................................... 98
Dynamic ARP Inspection .............................................................................................. 99
Settings .............................................................................................................. 99
ARP Inspection Validation ............................................................................... 100
ARP Inspection Port Settings ........................................................................... 101
ARP Inspection VLAN ....................................................................................... 101
ARP Inspection Statistics .................................................................................. 102
ARP Inspection VLAN ....................................................................................... 102
ACL ............................................................................................................................. 103
ACL Configuration Wizard ................................................................................ 103
Access Profile List ............................................................................................ 104
ACL Finder ........................................................................................................ 105
Tools........................................................................................... 107
Firmware Upgrade ..................................................................................................... 107
Upgrade your switch’s firmware ..................................................................... 107
Firmware Upgrade via HTTP Settings .............................................................. 107
Firmware Upgrade via TFTP Settings ............................................................... 108
Config Backup Restore ............................................................................................... 109
Config Backup/Restore .................................................................................... 109
Backup/Restore via HTTP Settings ................................................................... 109
Backup/Restore via TFTP Settings ................................................................... 109
Diagnostics................................................................................................................. 110
Cable Diagnostics Test ..................................................................................... 110
Reboot ....................................................................................................................... 111
Reboot/Reset to factory defaults .................................................................... 111
Ping ............................................................................................................................ 112
Network Connectivity Test (Ping Tool) ............................................................ 112
Using the Web Smart Switch Management Utility ....................... 113
System Requirements ................................................................................................ 113
Installation ................................................................................................................. 113
Using the Utility ......................................................................................................... 114
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
e
Launching the Utility ........................................................................................ 114
Discovery List ................................................................................................... 115
Monitor List ..................................................................................................... 115
Device Setting .................................................................................................. 116
Main Menu Options ......................................................................................... 117
Hardware Features and Specifications ......................................... 118
Web Smart Switch Series Software Specifications ........................ 120
Quick Installation GuideTroubleshooting ..................................... 122
Appendix .................................................................................... 123
© Copyright 2018 TRENDnet. All Rights Reserved.
i
TRENDnet User’s Guide
PoE Web Smart Switch Series
PoE Web Smart Switch Series Product Overview
TPE-082WS Overview
TPE-082WS
Package Contents
In addition to your switch, the package includes:
• Quick Installation Guide
• CD-ROM (Utility & User’s Guide)
• Power adapter (54V DC, 1.67A)
• Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-082WS Hardware Features
Front View
Rear View
• Reset Button – Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
• Mode Button – Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
• Gigabit Ethernet PoE+ Ports (1-8) – Connect either network PoE+ or
non-PoE devices.
• SFP Slots (9-10) – Supports optional 1000BASE-SX/LX mini-GBIC modules
for uplink or downlink connections.
© Copyright 2018 TRENDnet. All Rights Reserved.
ii
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
• Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
• PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
75W or above, the LED will turn on and the system will not
provide power additional PD (PoE client devices) after max
PoE budget is reached.
Off
:
When the PoE power provided is below the 75W PoE
power budget.
• Gigabit Ethernet PoE+ Port LEDs (1-8)
• Link/Activity button Mode
Green
on
:
Amber
on
:
Green
Blinking
:
Amber
Blinking
:
Off
• Gigabit Ethernet Port PoE+ LEDs (1-8)
• PoE LED button Mode
Green
on
:
Amber
on
:
Off
:
• SFP Slots (9-10)
• Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.
© Copyright 2018 TRENDnet. All Rights Reserved.
iii
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-1021WS Overview
TPE-1021WS
Package Contents
In addition to your switch, the package includes:
• Quick Installation Guide
• CD-ROM (Utility & User’s Guide)
• Power Cord (1.8m / 6 ft.)
• Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-082WS Hardware Features
Front View
Rear View
• Reset Button – Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
• Mode Button – Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
• Gigabit Ethernet PoE+ Ports (1-8) – Connect either network PoE+ or
non-PoE devices.
• SFP Slots (9-10) – Supports optional 1000BASE-SX/LX mini-GBIC modules
for uplink or downlink connections.
© Copyright 2018 TRENDnet. All Rights Reserved.
iv
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
• Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
• PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
130W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 130W PoE
power budget.
• Gigabit Ethernet PoE+ Port LEDs (1-8)
• Link/Activity button Mode
Green
on
:
Amber
on
:
Green
Blinking
:
Amber
Blinking
:
Off
• Gigabit Ethernet Port PoE+ LEDs (1-8)
• PoE LED button Mode – Green LED on
Green
on
:
Amber
on
:
Off
:
• SFP Slots (9-10)
• Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.
© Copyright 2018 TRENDnet. All Rights Reserved.
v
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-1620WS v2 & TPE-1620WSF Overview
Package Contents
In addition to your switch, the package includes:
• Quick Installation Guide
• CD-ROM (Utility & User’s Guide)
• Power cord (1.8 m / 6 ft.)
• Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-1620WS/TPE-1620WSF Hardware Features
Front View
Rear View
• Reset Button – Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
• Mode Button – Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
• PoE+ Gigabit Ports (1-16) – Connect network PoE+ or non-PoE devices.
• Gigabit Ethernet Ports (17-20) – Connect network devices. Ports 17-20
are shared with SFP slots 17F-20F and are disabled when SFP slots (17F-
20F) are in use.
• SFP Slots (17F-20F) – Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.
© Copyright 2018 TRENDnet. All Rights Reserved.
vi
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
• Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
• PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
185W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the PoE power
budget.
• Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
• Gigabit Ethernet Port LEDs (1-20)
• Link/Activity button Mode
Green
on
:
Amber
on
:
Green
Blinking
:
Amber
Blinking
:
Off
• Gigabit Ethernet PoE+ Port LEDs (1-16)
• PoE LED button Mode
Green
on
:
Amber
on
:
Off
:
• SFP Slots (17F-20F)
• Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.
© Copyright 2018 TRENDnet. All Rights Reserved.
vii
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-2840WS v2 Overview
Package Contents
In addition to your switch, the package includes:
• Quick Installation Guide
• CD-ROM (Utility & User’s Guide)
• Power cord (1.8 m / 6 ft.)
• Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-2840WS Hardware Features
Front View
Rear View
• Reset Button – Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
• Mode Button – Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
• PoE+ Gigabit Ports (1-24) – Connect network PoE+ or non-PoE devices.
• Gigabit Ethernet Ports (25-28) – Connect network devices. Ports 25-28
are shared with SFP slots 25F-28F and are disabled when SFP slots (25F-
28F) are in use.
• SFP Slots (25F-28F) – Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.
© Copyright 2018 TRENDnet. All Rights Reserved.
viii
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
• Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
• PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
185W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 185W PoE
power budget.
• Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
• Gigabit Ethernet Port LEDs (1-28)
• Link/Activity button Mode
Green
on
:
Amber
:
on
Green
Blinking
:
Amber
Blinking
:
Off
• Gigabit Ethernet PoE+ Port LEDs (1-24)
• PoE LED button Mode
Green
on
:
Amber
on
:
Off
:
• SFP Slots (25F-28F)
• Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.
© Copyright 2018 TRENDnet. All Rights Reserved.
ix
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-5028WS Overview
Package Contents
In addition to your switch, the package includes:
• Quick Installation Guide
• CD-ROM (Utility & User’s Guide)
• Power cord (1.8 m / 6 ft.)
• Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-5028WS Hardware Features
Front View
Rear View
• Reset Button – Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
• Mode Button – Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
• PoE+ Gigabit Ports (1-24) – Connect network PoE+ or non-PoE devices.
• Gigabit Ethernet Ports (25-28) – Connect network devices. Ports 25-28
are shared with SFP slots 25F-28F and are disabled when SFP slots (25F-
28F) are in use.
• SFP Slots (25F-28F) – Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.
© Copyright 2018 TRENDnet. All Rights Reserved.
x
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
• Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
• PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
370W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 370W PoE
power budget.
• Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
• Gigabit Ethernet Port LEDs (1-28)
• Link/Activity button Mode
Green
on
:
Amber
on
:
Green
Blinking
:
Amber
Blinking
:
Off
• Gigabit Ethernet PoE+ Port LEDs (1-24)
• PoE LED button Mode
Green
on
:
Amber
on
:
Off
:
• SFP Slots (25F-28F)
• Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.
© Copyright 2018 TRENDnet. All Rights Reserved.
xi
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-5240WS Overview
Package Contents
In addition to your switch, the package includes:
• Quick Installation Guide
• CD-ROM (Utility & User’s Guide)
• Power cord (1.8 m / 6 ft.)
• Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-5240WS Hardware Features
Front View
Rear View
• Reset Button – Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
• Mode Button – Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
• PoE+ Gigabit Ports (1-48) – Connect network PoE+ or non-PoE devices.
• Gigabit Ethernet Ports (49-52) – Connect network devices. Ports 49-52
are shared with SFP slots 49F-52F and are disabled when SFP slots (49F-
52F) are in use.
• SFP Slots (49F-52F) – Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.
© Copyright 2018 TRENDnet. All Rights Reserved.
xii
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
• Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
• PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
370W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 370W PoE
power budget.
• Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
• Gigabit Ethernet Port LEDs (1-52)
• Link/Activity button Mode
Green
on
:
Amber
on
:
Green
Blinking
:
Amber
Blinking
:
Off
• Gigabit Ethernet PoE+ Port LEDs (1-48)
• PoE LED button Mode
Green
on
:
Amber
on
:
Off
:
• SFP Slots (49F-52F)
• Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.
© Copyright 2018 TRENDnet. All Rights Reserved.
xiii
TRENDnet User’s Guide
PoE Web Smart Switch Series
TPE-5048WS Overview
Package Contents
In addition to your switch, the package includes:
• Quick Installation Guide
• CD-ROM (Utility & User’s Guide)
• Power cord (1.8 m / 6 ft.)
• Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
TPE-5048WS Hardware Features
Front View
Rear View
• Reset Button – Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will turn off to indicate
that the reset was initiated.
• Mode Button – Press the mode button to change LED indicators to
display Link/Activity Mode, or PoE Mode.
• PoE+ Gigabit Ports (1-48) – Connect network PoE+ or non-PoE devices.
• Gigabit Ethernet Ports (49-52) – Connect network devices. Ports 49-52
are shared with SFP slots 49F-52F and are disabled when SFP slots (49F-
52F) are in use.
• SFP Slots (49F-52F) – Supports optional 1000BASE-SX/LX mini-GBIC
modules for uplink or downlink connections.
© Copyright 2018 TRENDnet. All Rights Reserved.
xiv
TRENDnet User’s Guide
PoE Web Smart Switch Series
Diagnostic LEDs
• Power LED
On
:
When the Power LED is on, the device is receiving power.
Off
:
When the Power LED is off, the power adapter is not
connected or the device is not receiving power.
• PoE MAX (Power over Ethernet Max.)
On
:
When reaching near the max PoE power budget provided
740W or above, the LED will turn on and the system will
not provide power additional PD (PoE client devices) after
max PoE budget is reached.
Off
:
When the PoE power provided is below the 740W PoE
power budget.
• Fan Error
On
:
When the internal fan is not operating normally, the Fan
Error LED will turn on.
Off
:
When the internal fan is operating normally, the Fan Error
LED will remain off.
• Gigabit Ethernet Port LEDs (1-52)
• Link/Activity button Mode
Green
on
:
Amber
on
:
Green
Blinking
:
Amber
Blinking
:
Off
• Gigabit Ethernet PoE+ Port LEDs (1-48)
• PoE LED button Mode
Green
on
:
Amber
on
:
Off
:
• SFP Slots (49F-52F)
• Link/Activity
Green on
:
When the SFP LED is on, the link established using
the SFP module is operating at 1Gbps speed.
Green blinking
:
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
1Gbps link established.
Amber on
When the SFP LED is on, the link established using
the SFP module is operating at 100Mbps speed.
Amber blinking
When the SFP LED is blinking, the port is
transmitting or receiving data on through the
100Mbps link established.
Off
No link established.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148

Trendnet TPE-5028WS User guide

Category
Network switches
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI