IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microber cloth.
Assembly Instructions: 2073, 2074-SF (Smyth)
For Customer Service, contact
the place of purchase.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above. Remove
theoldxturefromtheceiling,includingtheoldmountingstrap.
1.Takethemountingstrapassemblyfromthepartsbag.Mountingstrap(B)contains
threadedholes.Twoofmountingscrews(A)shouldbeattachedtomountingstrap
(B).Youmayneedtotightennuts(C)thatholdthesescrewsinplace.
2.Placemountingstrap(B)overthejunctionboxsothatmountingscrews(A)are
vertical,andinalignmentwiththeholelocationsonthexture’scanopy(D).Secure
mountingstrap(B)tothejunctionboxwithmountingscrews(D)andascrewdriver.
Tightenthescrewssecurely.
3.Placethexture’ssocketcluster(R)onaatsurface.Rod(N)isonthexture’s
wires,butnotattachedtothebodyofthexture.Passthexture’swiresthroughrod
(N) and pull the wires until taut. Twist rod (N) into post (V) until secure. Attach rods
(M)tothehooks(O)onthexture’sbody.
4.Bymeasuring,determinethecorrectnumberofchainlinksneededforproper
hangingheight.Ifnecessary,useapairofplierstoopenandremoveanyexcess
chain. Attach one chain connector (K) to each end of chain (J). Use one of chain
connectors (K) to attach chain (J) to top loop (L) and close the chain connector.
5.Haveanassistantattachrods(M)tothehooksonthexturebodythenattachthe
hooks of rods (M) to top loop (L). Hook the end of rod (N) onto top loop (L). Pull the
wiresthroughtoploop(L).Feedthexture’swiresupthroughthechain(everythree
linksorso),pullingthewiresuntiltaut.Slidecanopyloopcollar(H)andcanopy(G)
ontothechain/wires.Usethefreechainconnector(K)toattachchain(J)tocanopy
loop (H).
CONNECTING THE WIRES
6.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refer
tothewiringdiagrambelowandattachthexture’swirestothepowersupply
wiresfromthejunctionbox.ConnectHottoHot,NeutraltoNeutral,andGroundto
Ground.Twisttheendsofthewirepairstogether,andthentwistonawireconnector.
Makesurealltwistsareinthesamedirection.Ifthereisnohousegroundwire
comingfromthejunctionbox,locategroundscrew(E)onthemountingbracket/
mountingstrapandwrapthexture’sgroundwirearoundthegroundscrew.Use
ascrewdrivertotightenthetopofgroundscrew(E)ontothewiresandintothe
mountingbracket/mountingstrap.Tuckthewiresintothejunctionbox.
FINISHING THE INSTALLATION
7.Raisecanopy(D)totheceiling.Slide canopy loop (H) and canopy loop collar (I)
upbeneaththecanopy.Tightlythreadcanopyloopcollar (I) onto canopy loop (H) to
secure canopy (D) in place.
8Slidecandlesleeves(Q)overthesockets.Installlightbulbs(notincluded)in
accordancewiththexture’sspecications.
9.Placeglassshade(S)ontobottomcap(T).Raiseglassshade(S)andbottomcap
(T)upbeneaththelightsource.Twistbottomnial(U)ontothethreadsatthebottom
ofthelightsource.Tightensecurely.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
PENDANT
INSTALLATION
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
House Wires
Fixture Wires
Hot
U
R
S
T
A
B
C
H
I
D
J
K
F
E
G
L
M
V
N
P
O
Q