Deagostini Fiat 126p User guide

PackPack

77

STAGE PAGE

31 A wheel and tyre 105

32 Fitting the wheel 108

33 Left engine cover 111

34 Left rear wheel arch 114

35 Engine top cover 117

Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.

Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.

Warning: Not suitable for children under the age of 14.

is product is not a toy and is not designed or intended for use in play.

Items may vary from those shown.

105

Your parts:

31A. Outer wheel rim

31B. Inner wheel rim

31C. Tyre

DP. 2 x 3mm washer screws

Stage 31: A wheel and tyre

106

2 Turn the assembly around and place the inner wheel rim (31C)

into the tyre.

1 Start the wheel assembly by inserting the outer wheel rim (31B)

into the tyre (31A).

3Secure the parts together with three DM screws.

107

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

108

Stage 32: Fitting the wheel

Your parts:

32A. Wheel trim

32B. Valve

32C. Washer

32D. Brake plate

32E. Handbrake actuating lever

32F. Front brake lines

CM. 2.3 x 4mm screws

109

3 Prepare the wheel assembled in the previous stage and insert

the valve (32B) into the hole in the outer wheel rim.

2 Slide the end of one of the rear brake lines (32F) onto the pin on

the lever.

1 Mount the handbrake actuating lever (32E) onto the indicated pin

of the brake plate (32D).

4Place the right front brake plate (32D) onto the right rear

suspension. Fit the rear wheel onto the right wheel hub (4H).

Place a washer (32C) into the centre of the wheel and secure both to

the hub with a CM screw.

5 Take the wheel trim (32A) and fit it over the screw. 6Pass the free end of the brake line over the driveshaft. Connect

the end of the cable to the tab on the cable cover (14G) between

the fuel tank and transmission mounts.

110

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

111

Your parts:

33A. Left engine cover

33B. Rear wall

AM. 1.7 x 3mm screws

Stage 33: Left engine cover

112

1Take the left engine cover (33A) and place it onto the left side of

the chassis, aligning the holes of both parts. 2Secure the left engine cover to the chassis with four AM screws.

113

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

114

Stage 34: Left rear wheel arch

Your parts:

34A. Left rear wheel arch

34B. Side engine cover

34C. Regulator

DP. 1.7 x 5mm screws

BM. 2 x 4mm screws

115

2Secure the regulator with a DP screw from the other side.

1Insert the pin on the reverse of the regulator (34C) into the

indicated hole in the left rear wheel arch (34A).

3Place the left rear wheel arch onto the chassis, aligning the

corresponding holes of both parts. Secure with two BM screws.

5 Secure the cover with a DP screw from the other side of the arch.

4 Place the side engine cover (34B) up against the left rear wheel

arch, aligning the post with the hole.

116

Here is how your assembly should look at the end of this stage. Keep any assemblies,

unused parts and spares labelled to one side for later use.

117

Your parts:

35A. Left air inlet cover

35B. Right air inlet cover

35C. Engine top cover

DP. 1.7 x 5mm screws

Stage 35: Engine top cover

118

2 Secure the air inlet cover with two DP screws.

1 Place the left air inlet cover (35A) onto the engine top cover (35C),

inserting the posts into the holes.

4 Secure the air inlet cover with two more DP screws.

3Place the right air inlet cover (35B) onto the engine top

cover (35C).

119

Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.

Deagostini Fiat 126p User guide

Deagostini Fiat 126p User guide

Related papers

Other documents