Road Armor Stealth Steel Fender Flares Installation guide

Brand
Road Armor
Model
Stealth Steel Fender Flares
Category
Car kits
Type
Installation guide

This manual is also suitable for

Road Armor Stealth Steel Fender Flares are a durable and stylish upgrade for your 2018+ Jeep Wrangler JL or 2020+ Jeep Gladiator JT. Made from high-strength steel, these fender flares provide superior protection for your vehicle's body from road debris, rocks, and other hazards. Installation is straightforward and requires basic tools and drilling. The fender flares come complete with all necessary hardware, including 8" accent lights with a wiring harness, and DOT-approved reflective strips for added safety.

Road Armor Stealth Steel Fender Flares are a durable and stylish upgrade for your 2018+ Jeep Wrangler JL or 2020+ Jeep Gladiator JT. Made from high-strength steel, these fender flares provide superior protection for your vehicle's body from road debris, rocks, and other hazards. Installation is straightforward and requires basic tools and drilling. The fender flares come complete with all necessary hardware, including 8" accent lights with a wiring harness, and DOT-approved reflective strips for added safety.

INSTALL INSTRUCTIONS
Applicaon : 2018+ Jeep Wrangler JL
2020+ Jeep Gladiator JT
JL / JT FRONT FENDER FLARE: 518AFF0B
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 2 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
SAFETY FIRST!
• FOLLOW ALL INSTRUCTIONS, YOUR SAFETY AND THE SAFETY OF OTHERS IS MOST IMPORTANT.
• WEAR APPROPRIATE EYE PROTECTION AND EXERCISE CAUTION WHEN DRILLING / CUTTING
REQUIRED TOOLS
INCLUDED HARDWARE
I WARNING
Read the instrucons completely before beginning installaon. Before ghtening bolts,
drilling or cung where required, check to make sure there are no obstrucons such as
brake, fuel or electrical lines which may be damaged. Also keep in mind this is an aer-
market product and MAY require minor shimming and/or trimming, reaming, etc. for
proper t. Road Armor is not responsible for any damages to vehicle.
IMPORTANT NOTICE
• Be sure to inspect and test t your product to ensure proper tment before having it coated, painted, bed
lined, etc.
• Road Armor will not be responsible for the cost of coang your unit if any problems with t or nish are not
noted and addressed beforehand.
Metric and SAE Socket Sets and Wrenches
Drill & Unibit
Cut-O Wheel
(2) 8” Accent Lights and Harness
(4) 10-24x1/2” Bolts
(4) 10-24 Flange Nuts
(4) 5/16”x1” Carriage Bolts
(12) 5/16”x1” Bolts
(16) 5/16” Flange Nuts
(4) 5/16” Push Retainer Washers
(12) 5/16” Washers
118” Rubber Edge Trim
(1) PSG FENDER FLARE
(1) DVR FENDER FLARE
(1) DOT REFLECTIVE STRIP
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 3 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Using 8mm & 10mm sockets, remove bolts securing OEM fenders.
2 Remove two OEM push clips that secure fender liners
3 Remove rear fender assembly by rmly pulling on one end of fender unl all 10 clips “pop o”.
4 Unclip and unplug OE fender light harness from inner fender well. REMOVE OE FENDER VENT
1
2
5 Using cut-o wheel, remove both OEM fender
mounts and paint edges to protect as show below.
5
4
5
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 4 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Mark and Drill 8 holes to 3/8” as shown below.
2 Install 8” ACCENT LIGHT into FENDER FLARES using 2 - #10-24 BOLTS and FLANGE NUTS.
3 Assembly FRONT FENDER using 2 - 5/16” CARRIAGE BOLTS and PUSH RETAINING WASHERS.
1
3
2
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 5 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Install EDGE TRIM along main fender edge to protect body. (Trim ribbed side on boom.)
1
2 Install FENDER FLARE by inserng 2 - 5/16” CARRIAGE BOLTS into boom rear holes rst.
3 Loosely installing one of 4 - 5/16” BOLT and FLANGE NUT through FENDER FLARE “top center” to
hold/support FENDER FLARE onto OE fender while installing remaining 5/16” Hardware.
2
3
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 6 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Connue installing FENDER FLARES using 2 - 5/16” HARDWARE as shown below and *TIGHTEN ALL*
1
2
3 Safely secure accent light harness with zip es
and plug into factory plug.
NOTE If Required: Install 1x1 Inch DOT REFLECTIVE TAPE to side of each fender provide in kit.
2 Push kit EDGE TRIM against body for nished look.
FINISHED!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Road Armor Stealth Steel Fender Flares Installation guide

Brand
Road Armor
Model
Stealth Steel Fender Flares
Category
Car kits
Type
Installation guide
This manual is also suitable for

Road Armor Stealth Steel Fender Flares are a durable and stylish upgrade for your 2018+ Jeep Wrangler JL or 2020+ Jeep Gladiator JT. Made from high-strength steel, these fender flares provide superior protection for your vehicle's body from road debris, rocks, and other hazards. Installation is straightforward and requires basic tools and drilling. The fender flares come complete with all necessary hardware, including 8" accent lights with a wiring harness, and DOT-approved reflective strips for added safety.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents