Road Armor 520AFR0B Installation guide

Brand
Road Armor
Model
520AFR0B
Category
Car kits
Type
Installation guide

This manual is also suitable for

INSTALL INSTRUCTIONS
Applicaon : 2018+ Jeep Wrangler JL
2020+ Jeep Gladiator JT
JL / JT FRONT FENDER FLARE: 518AFF0B
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 2 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
SAFETY FIRST!
• FOLLOW ALL INSTRUCTIONS, YOUR SAFETY AND THE SAFETY OF OTHERS IS MOST IMPORTANT.
• WEAR APPROPRIATE EYE PROTECTION AND EXERCISE CAUTION WHEN DRILLING / CUTTING
REQUIRED TOOLS
INCLUDED HARDWARE
I WARNING
Read the instrucons completely before beginning installaon. Before ghtening bolts,
drilling or cung where required, check to make sure there are no obstrucons such as
brake, fuel or electrical lines which may be damaged. Also keep in mind this is an aer-
market product and MAY require minor shimming and/or trimming, reaming, etc. for
proper t. Road Armor is not responsible for any damages to vehicle.
IMPORTANT NOTICE
• Be sure to inspect and test t your product to ensure proper tment before having it coated, painted, bed
lined, etc.
• Road Armor will not be responsible for the cost of coang your unit if any problems with t or nish are not
noted and addressed beforehand.
Metric and SAE Socket Sets and Wrenches
Drill & Unibit
Cut-O Wheel
(2) 8” Accent Lights and Harness
(4) 10-24x1/2” Bolts
(4) 10-24 Flange Nuts
(4) 5/16”x1” Carriage Bolts
(12) 5/16”x1” Bolts
(16) 5/16” Flange Nuts
(4) 5/16” Push Retainer Washers
(12) 5/16” Washers
118” Rubber Edge Trim
(1) PSG FENDER FLARE
(1) DVR FENDER FLARE
(1) DOT REFLECTIVE STRIP
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 3 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Using 8mm & 10mm sockets, remove bolts securing OEM fenders.
2 Remove two OEM push clips that secure fender liners
3 Remove rear fender assembly by rmly pulling on one end of fender unl all 10 clips “pop o”.
4 Unclip and unplug OE fender light harness from inner fender well. REMOVE OE FENDER VENT
1
2
5 Using cut-o wheel, remove both OEM fender
mounts and paint edges to protect as show below.
5
4
5
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 4 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Mark and Drill 8 holes to 3/8” as shown below.
2 Install 8” ACCENT LIGHT into FENDER FLARES using 2 - #10-24 BOLTS and FLANGE NUTS.
3 Assembly FRONT FENDER using 2 - 5/16” CARRIAGE BOLTS and PUSH RETAINING WASHERS.
1
3
2
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 5 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Install EDGE TRIM along main fender edge to protect body. (Trim ribbed side on boom.)
1
2 Install FENDER FLARE by inserng 2 - 5/16” CARRIAGE BOLTS into boom rear holes rst.
3 Loosely installing one of 4 - 5/16” BOLT and FLANGE NUT through FENDER FLARE “top center” to
hold/support FENDER FLARE onto OE fender while installing remaining 5/16” Hardware.
2
3
2018+ JEEP JL / JT FRONT FENDER FLARES Page ( 6 of 6)
www.ROADARMOR.com
INSTALL INSTRUCTIONS
1 Connue installing FENDER FLARES using 2 - 5/16” HARDWARE as shown below and *TIGHTEN ALL*
1
2
3 Safely secure accent light harness with zip es
and plug into factory plug.
NOTE If Required: Install 1x1 Inch DOT REFLECTIVE TAPE to side of each fender provide in kit.
2 Push kit EDGE TRIM against body for nished look.
FINISHED!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Road Armor 520AFR0B Installation guide

Brand
Road Armor
Model
520AFR0B
Category
Car kits
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents