Mettler Toledo InPro 5000 (i) Sensors Operating instructions

Page is loading ...

 14 InPro 5000 (i) CO

2

Sensor Series

30 313 393 B PrintedinSwitzerland

1 Introduction ................................................................... 15

2 Safetyinstructions .......................................................... 15

3 Productdescription ........................................................ 15

4 Sensorinstallation .......................................................... 16

4.1 Connection .................................................................... 16

5 Operation ..................................................................... 16

5.1 CalibrationofthepHsensor ............................................ 16

5.2 Mountingthemembranebody ......................................... 17

5.3 CalibrationoftheCO

2

sensor .......................................... 17

6 Maintenance .................................................................. 17

7 Disposal ....................................................................... 17

8 Warranty ....................................................................... 17

9 Storagecondition ........................................................... 17

10 ECDeclarationofConformity ........................................... 17

Contents

InPro 5000 (i)

CO

2

Sensors

Quick Setup Guide

InProandISMareregisteredtrademarksof

Mettler-ToledoGmbHinSwitzerland,theUSA,

theEuropeanUnionandafurthervecountries.

en

en QuickSetupGuide

InPro 5000 (i) CO

2

Sensor Series 15

InPro 5000 (i) Sensor Series © 06/2019Mettler-ToledoGmbH

PrintedinSwitzerland 30 313 393 B

1 Introduction

Thank you for buying this InPro 5000(i) sensor from

METTLER TOLEDO.  InPro 5000(i) sensors are intended

solelyfor in-line measurementof dissolved CO

2

 (carbon

dioxide).

2 Safety instructions

h

Notice:TheInPro5000(i)sensorshouldbeinstalled,oper-

ated,maintainedonlybypersonnelfamiliarwiththesensor

andwhoarequaliedforsuchwork.

h

Notice:Adefectivesensormustneitherbeinstallednorput

intoservice.

a

Caution: Only the maintenance work described in these

operatinginstructionsmaybeperformedonthesensors.

h

Notice:Whenchangingfaultycomponents,useonlyorig-

inal spare parts obtainable from your METTLER TOLEDO

supplier.

h

Notice:Nomodicationstothesensorortheaccessories

areallowed.Themanufacturer/supplieracceptsnorespon-

sibilityfordamagecausedbyunauthorizedmodications.

Theriskisborneentirelybytheuser.

3 Product description

 Eachsensorissuppliedtogetherwith:

 –1bottleCO

2

-electrolyte25ml

 –1qualitycontrolcerticate

 –1inspectioncerticate3.1(inaccordancewithEN

10 2 0 4. 3 / 3.1)

 –1quicksetupguide

 –1ECDeclarationofConformity

 Membranebodyandcapsleevearenotmounted.Theinte-

riorbodyisprotectedagainstdryingoutwithawettingcap,

lledwithCO

2

-electrolyte.

 Pleasecheckcompleteness.

en

 16 InPro 5000 (i) CO

2

Sensor Series

30 313 393 B PrintedinSwitzerland

1 VPconnector

2 ISMconnector

3 Hexagonalscrew

4 ThreadedsleevePg13.5

5 WasherPTFE

6 O-Ring(10.77×2.62mm,

 SiliconeFDA/USPVI)

7 Retainernut

8 Membranebody

9 Interiorbody

10 Capsleeve

11 Wettingcap

4 Sensor installation

4.1 Connection

Theinteriorbody(pHelectrode)isreadyforcalibration.

–Onunpacking,checkthepHelectrodeformechanicalda-

mage.ReportanydamageimmediatelytoyourMETTLER

TOLEDOsupplier.

–Removethewateringcap,capsleeve,membranebody

andbrieyrinsethesensorwithde-ionizedwater.

–Afterrinsing,thesensorshouldonlybedabbeddrywitha

tissue.DonotrubthepH-sensitiveglassasthiscanlead

toelectrostaticchargingandsluggishresponsetimes.

–CheckinsidethepH-sensitiveglassforthepresenceof

any air bubbles and remove same by gently swinging

theelectrodeinaverticalplane(shakingdownaswitha

thermometer).

–CalibratethepHsensorasdescribedinSection5.

–Placetheelectrodeintothehousingasdescribedinthe

instructionsforthehousing.

h

Notice:Mountingupside-downorhorizontallyisnotpos-

sibleduetotheinternalpHelectrode.Anangleof15°or

greatertohorizontalisneeded.

–Connect the electrode and the pH transmitter with the

correspondingcable(AK9fortheInPro5000(i),VPfor

the InPro 5000). Observe the connection scheme that

accompaniesthecableorthetransmitter.

– ISM

®

sensorssuchasInPro5000ienablePlugandMea-

surestartupandexpandeddiagnostics.Forinstallation,

commissioningandoperationoftheISMsystemplease

refertoinstructionsforthetransmitter,moduleandcable.

5 Operation

5.1 Calibration of the pH sensor

(NotneededforInPro5000i)

a:Min.immersiondepth>25mm/1"

For the analog CO

2

 sensor InPro 5000,we recommend

a2-pointcalibrationinpHbuffers7.00and9.21.Before

calibration,rstremovewettingcap.StartwithbufferpH

7.00fordeterminingzeropointandthenbufferpH9.21for

determiningtheslope.Pleaserefertoinstructionmanualof

thetransmitterforfurtherdetails.

h

Notice:Onthetransmitter,selectPt1000asthetempera-

turesensorfortheanalogInPro5000.TheInPro 5000i

doesnotrequireatemperaturesetting.

en

InPro 5000 (i) CO

2

Sensor Series 17

InPro 5000 (i) Sensor Series © 06/2019Mettler-ToledoGmbH

PrintedinSwitzerland 30 313 393 B

h

Notice:Pleasedonotleavethesensorinthecalibration

bufferforlongerthan1hour.Toolonganexposuremay

resultinhighsensordriftintheprocess.

5.2 Mounting the membrane body

–AftercalibrationofthepHelectroderinsethepHelectrode

withde-ionizedwaterandcarefullydabitwithapaper

tissue.

–FillthenewmembranebodyhalfwaywithCO

2

electroly te.

–Makesurethatallairbubblesareremovedfromthemem-

brane body. Air bubbles can be removed by carefully

tappingonthemembranebody.

–Slip the membrane body over the pH electrode while

holding the sensor in a vertical position. The excess

electrolytethatwillbedisplacedshouldberemovedwith

apapertissue.

h

Notice: No electrolyte, sample media or contamination

shouldbepresentbetweenthemembranebodyandthe

capsleeve.Pleasecheckcarefully.

–Carefully slip the cap sleeve over the tted membrane

body,holdingthesensorinaverticalposition,andscrew

ittight.Thecapsleevemustbecleanandtight.

5.3 Calibration of the CO

2

sensor

TheInPro5000isinsitusterilizableorinanautoclave.After

sterilizationaprocesscalibrationstepisneededtoachieve

accuratemeasurements.

The process calibration can be performed by using the

transmitter’s calibration menu. For further details please

refertothemainmanual.

6 Maintenance

Werecommendusinganewmembranebodyaftereach

batch.AftereachcalibrationofthepHelectrodenewCO

2

electrolyteshouldbelledinthemembranebody.

IfthepHelectrodeshowsasluggishresponsetimeand/or

insufcientsensitivity,thepH-sensitiveglasscanbereac-

tivatedusinganHFsolution(p/n51319053).Forfurther

detailspleaserefertothemainmanual.

Typically,after10–20sterilizationcyclesthepHelectrode

shouldbereplaced.Pleaserefertotheinstructionmanual

ofthereplacementinteriorbodyInPro5000(i).

7 Disposal

Itistheuser’sresponsibilitytodisposeofthespentspare

partsandifnecessarythesensorinaprofessionalmanner.

Sensorscontainelectroniccomponentsthatrequirespecial

disposalwithoutanyhazardforhumans,andwithnorisk

ofharmtotheenvironment.Pleaseobservetheapplicable

localor national regulationsconcerning the disposal of

"wasteelectricalandelectronicequipment".

8 Warranty

Warrantedfreeofmanufacturingdefectsforatermof12

monthsafterdelivery.

9 Storage condition

Forstoragewerecommendllingthemembranebodywith

freshCO

2

electrolyteandreconnectingittothesensor.The

wetting cap, lled with CO

2

-electrolyte, will prevent dry-

ing-outofthemembrane.

10 EC Declaration of Conformity

Thecompletedeclarationisavailableinthedeclarationof

conformitycerticate.

en

Page is loading ...

 74 InPro 5000 (i) CO

2

Sensor Series

30 313 393 B PrintedinSwitzerland

–

Notes

InPro 5000 (i) CO

2

Sensor Series 75

PrintedinSwitzerland 30 313 393 B

Notes

–

Mettler-ToledoGmbH,ProcessAnalytics

ImHackacker15,CH-8902Urdorf,Switzerland

Phone+41447296211,Fax+41447296636

Subjecttotechnicalchanges.

PrintedinSwitzerland.30313393B

www.mt.com/pro

ForaddressesofMETTLERTOLEDO

MarketOrganizationspleasegoto:

www.mt.com/pro-MOs

Management System

certified according to

ISO 9001 / ISO 14001

9001

certified

ISO

14001

certified

ISO

1258

Mettler Toledo InPro 5000 (i) Sensors Operating instructions

Mettler Toledo InPro 5000 (i) Sensors Operating instructions

in other languages

Related papers

Other documents