Page is loading ...
MANUAL
LANTIME M600 GPS
Stratum 1 NTP Time Server
Table of Contents
1 Impressum 1
2 Quick Start 2
3 Network Timeserver with GPS synchronized time base 3
4 The Modular System LANTIME 4
5 Network Time Protocol (NTP) 7
6 GPS satellite controlled clock 9
7 Mounting the GPS Antenna 11
8 Booting the GPS170 receiver 14
9 Booting the Single Board Computer 15
10 Configuration User Interface 16
1 Impressum
2 Quick Start
Starting up
please wait...
NTP: Offs. 1ms Stratum: 1
GPS: NORMAL OPERATION Satellites:9/10
PTP: ok PTP_MASTER GM:00:00:00:00:00:00
Press F1 for help or F2 for setup overview
F1
UTC
Tue, 01.01.2008
12:00:00
F1
UTC Tue, 01.01.2008
12:00:00
↓, →, ↓, →, ↓, →
SATELLITE CONSTELLATION
satellites in view: 9
good satellites : 9
selected set: 13 24 5 6
Global Configuration
->Network Interfaces <-
Network Services
ETH0: -> DHCP:disable <-
ADDRESS: 192.168.10.20
NETMASK: 255.255.255.000
DEF.GATEWAY: 192.168.10.1
3 Network Timeserver with GPS synchronized
time base
4 The Modular System LANTIME
OK
ESC
Time Service
Ref. Time
Network
Alarm
Terminal
USB
F1
F2
1
2
3
4
5
ENGLISH
1. VF Display 256 x 64 dots
2. Function buttons: 4-way navigation; F1, F2, OK, ESC
3. Status LEDs: Ref. Time, Time Service, Network, Alarm
4. Terminal / VT100, 38400 Baud, 8N1, 9pin. D-SUB male
5. USB connector
DEUTSCH
1. VF Display, 256 x 64 Punkte
2. Funktionstasten: 4 Wege Navigation; F1, F2; OK, ESC
3. Status LEDs: Ref. Time, Time Service, Network, Alarm
4. Terminal / VT100, 38400 Baud, 8N1, 9pol. D-SUB Stecker
5. USB Anschluss
LANTIME M600
NTP: Offs. PPS: 5us Stratum: 1
GPS: NORMAL OPERATION Satellites: 8/8
PTP2: ok INITIALIZING GM: 00...........
Press F1 for help or F2 for setup overview
07:23:25
UTC
Thu, 30.12.2010
GPS
Antenna
Error
O
I
100-240V AC
50/60Hz
PPS Out
1
2
34
5
79
ENGLISH
1. Power supply connector
2. Serial Port COM 0, 9pin. D-SUB, female
3. Serial Port COM 1, 9pin. D-SUB, female
4. Error relay output, 3pin. DFK
5. GPS Antenna, BNC
6. Time Code AM / DCLS output, BNC
7. PPS / 10MHz output, BNC
8. F. Synth. / PPM output, BNC
9. Network connectors ETH0 - ETH3, 10/100 Mbit RJ45
DEUTSCH
1. Spannungsversorgung
2. Serielle Schnittstelle COM 0, 9pol. D-SUB Buchse
3. Serielle Schnittstelle COM 1, 9pol. D-SUB Buchse
4. Störmelderelaisausgang, 3pol. DFK
5. GPS Antenne, BNC
6. Time Code AM / DCLS Ausgang, BNC
7. PPS / 10MHz Ausgang, BNC
8. F. Synth. / PPM Ausgang, BNC
9. Netzwerk Anschlüsse ETH0 - ETH3, 10/100MBit RJ45
COM 1
COM 0
CO NO NC
10MHz Out
TC DCLS Out
6
TC AM Out
F. Synth. Out
8
PPM Out
100M 10M
ETH0
ETH1
100M 10M
ETH2
ETH3
4.1 Supported Network Services
4.2 Additional Features
•
•
•
•
•
•
4.3 User Interface
•
•
•
•
•
•
•
•
4.4 Input and Output Options
•
•
•
•
•
4.5 Why to use a Network Time Server?
•
•
•
•
•
5 Network Time Protocol (NTP)
5.1 NTP Target
5.2 NTP-Client Installation
6 GPS satellite controlled clock
6.1 GPS Clock Features
6.2 Time Zone and Daylight Saving
7 Mounting the GPS Antenna
◦
◦ ◦
7.1 Example:
7.2 Antenna Assembly with Surge Voltage Protection
7.3 Antenna Short-Circuit
ANTENNA
SHORT-CIRCUIT
DISCONNECT POWER
! ! !
8 Booting the GPS170 receiver
/
