Meinberg LANTIME M600 User manual

MANUAL

LANTIME M600 MRS

Multi Reference Source NTP Server

Table of Contents

1 Impressum 1

2 Quick Start 2

3 Network Timeserver synchronized by multiple reference time sources 4

4 The Modular System LANTIME 5

5 Network Time Protocol (NTP) 8

6 GPS satellite controlled clock with MRS option 10

7 Mounting the GPS Antenna 13

8 Booting the GPS170 receiver 16

9 Booting the Single Board Computer 17

10 Conﬁguration User Interface 18

11 The graphical user interfaces 48
12 The WEB Interface 49

The Command Line Interface 87
SNMP Support 98
Attachment: Technical Information 109

16 Konformit

¨

atserkl

¨

arung 154

1 Impressum

2 Quick Start

MEINBERG LANTIME

is booting... please wait...

.......

NTP: Offs. 1ms Stratum: 1

MRS: sync to GPS XTL:SYNC SVs:9/10

PTP: ok PTP_SLAVE GM:00:00:00:00:00:00

Press F1 for help or F2 for setup overview

F1

UTC

Tue, 01.01.2008

12:00:00

↓, ok, ↓, ok, →, ok

MRS Status

-> Setup Input Priorities <-

Setup Fixed Offsets

Setup Precisions

1.GPS is master : -10ns

2.PPS in is available : -20ns

3.IRIG no signal : n/a

4.NTP is available : -30.000us

2.PTP (IEEE1588)is available : -300ns

F1

MRS Input Priorities

↓, →, →, ↓, →

GPS Receiver Position

-> Satellite Constellation <-

GPS Status & Version

SATELLITE CONSTELLATION

satellites in view: 5

good satellites : 5

selected set: 04 09 21 17

Global Configuration

->Network Interfaces <-

Network Services

ETH0: -> DHCP:disable <-

ADDRESS: 192.168.10.20

NETMASK: 255.255.255.000

DEF.GATEWAY: 192.168.10.1

3 Network Timeserver synchronized by multiple

reference time sources

4 The Modular System LANTIME

OK

ESC

Time Service

Ref. Time

Network

Alarm

Terminal

USB

F1

F2

1

2

3

4

5

ENGLISH

1. VF Display 256 x 64 dots

2. Function buttons: 4-way navigation; F1, F2, OK, ESC

3. Status LEDs: Ref. Time, Time Service, Network, Alarm

4. Terminal / VT100, 38400 Baud, 8N1, 9pin. D-SUB male

5. USB connector

DEUTSCH

1. VF Display, 256 x 64 Punkte

2. Funktionstasten: 4 Wege Navigation; F1, F2; OK, ESC

3. Status LEDs: Ref. Time, Time Service, Network, Alarm

4. Terminal / VT100, 38400 Baud, 8N1, 9pol. D-SUB Stecker

5. USB Anschluss

LANTIME M600

NTP: Offs. PPS: 5us Stratum: 1

GPS: NORMAL OPERATION Satellites: 8/8

PTP2: ok INITIALIZING GM: 00...........

Press F1 for help or F2 for setup overview

07:23:25

UTC

Thu, 30.12.2010

GPS

Antenna

Error

O

I

100-240V AC

50/60Hz

1

4

3511

ENGLISH

1. Power supply connector

2. GPS Antenna, BNC

3. Serial Port COM 1, 9pin. D-SUB, female

4. Serial Port COM 0, 9pin. D-SUB, female

5. Error relay output, 3pin. DFK

6. PPS / Freq. In input, BNC

7. Time Code AM / DCLS input, BNC

8. Time Code AM / DCLS output, BNC

9. PPS / 10MHz output, BNC

10. F. Synth. / PPM output, BNC

11. Network connectors ETH0 - ETH3, 10/100 Mbit RJ45

DEUTSCH

1. Spannungsversorgung

2. GPS Antenne, BNC

3. Serielle Schnittstelle COM 1, 9pol. D-SUB Buchse

4. Serielle Schnittstelle COM 0, 9pol. D-SUB Buchse

5. Störmelderelaisausgang, 3pol. DFK

6. PPS / Freq. In Eingang, BNC

7. Time Code AM / DCLS Eingang, BNC

8. Time Code AM / DCLS Ausgang, BNC

9. PPS / 10MHz Ausgang, BNC

10. F. Synth. / PPM Ausgang, BNC

11. Netzwerk Anschlüsse ETH0 - ETH3, 10/100MBit RJ45

COM 1

COM 0

CO NO NC

100M 10M

ETH0

ETH1

2

PPS In

6

Freq. In

TC AM In

7

TC DCLS In

TC DCLS Out

8

TC AM Out

PPS Out

9

10MHz Out

F. Synth. Out

10

PPM Out

100M 10M

ETH2

ETH3

4.1 Supported Network Services

4.2 Additional Features

•

4.3 User Interface

•

4.4 Input and Output Options

•

4.5 Why to use a Network Time Server?

•

5 Network Time Protocol (NTP)

5.1 NTP Target

5.2 NTP-Client Installation

         



         

         

6 GPS satellite controlled clock with MRS option

6.1 MRS functionality

•

1.GPS * 20ns 2.PPS 30ns

2.NTP 30.000us

1.GPS is master : -10ns

2.PPS in is available : -20ns

3.IRIG no signal : n/a

4.NTP is available : -30.000us

2.PTP(IEEE1588)is available : -300ns

F1

MRS Input Priorities

1.GPS * 20ns

2.PPS 30ns

3.NTP 30.000us

M300: LC-Display 40 x 2 Characters

M400 / M900: LC-display, 4 x 16 Characters

M600: Vacuum fluorescent graphic display (VFD), 256 x 64 dots

6.2 GPS functionality

6.3 GPS Clock Features

6.4 Time Zone and Daylight Saving

7 Mounting the GPS Antenna

◦

◦ ◦

7.1 Example:

7.2 Antenna Assembly with Surge Voltage Protection

Page is loading ...

Meinberg LANTIME M600 User manual

Meinberg LANTIME M600 User manual

Related papers

Other documents