Page is loading ...
ILite 3 display sy stem
Installation manual
R5976695/03
27/04/2006
Barco nv Media
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.83.86
E-mail: [email protected]
Visit us at the web: www.barco.com
Barco nv Events
Noord
laan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail:
Visit us at the web: www.barco.com
PrintedinBelgium
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC r
ules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of t
his equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves t
o be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided
the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are
system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing a
nd maintenance regulations specified in the this manual must be complied with by
the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufactures.
Table of contents
TABLE OF CONTENTS
1. Safety................................................................................................................. 3
1.1 Safety guidelines ..................................................................................................................... 3
1.2 Important safety instructions ......................................................................................................... 4
1.3 Important warnings ................................................................................................................... 5
2. System Overview................................................................................................... 7
2.1 Introduction ........................................................................................................................... 7
2.2 ILite 3 display tiles.................................................................................................................... 8
2.2.1 Introduction..................................................................................................................... 8
2.2.2 ILite 3 specifications ........................................................................................................... 8
2.2.3 ILite 3 dimensions.............................................................................................................. 9
2.3 ILite 3 flight case for 24 tiles ......................................................................................................... 9
2.3.1 Introduction..................................................................................................................... 9
2.3.2 Flight case dimensions .......................................................................................................10
2.4 ILite 3 setup accessories............................................................................................................ 11
2.5 Cables for ILite 3 displays........................................................................................................... 12
2.5.1 Power cables.................................................................................................................. 12
2.5.2 Data cables ...................................................................................................................13
2.6 Power boxes.........................................................................................................................14
2.7 Digitizer ..............................................................................................................................14
2.8 Fiberlink system .....................................................................................................................15
2.9 Control software ..................................................................................................................... 15
3. Set up a complete ILite 3 display system .....................................................................17
3.1 Set up a floor mount ILite 3 display................................................................................................. 17
3.2 Set up a hanging ILite 3 display. ....................................................................................................17
4. Basic Setup Procedures .........................................................................................19
4.1 Locating ILite 3 parts ................................................................................................................ 19
4.2 Handle the ILite 3 flight case for 24 tiles............................................................................................ 20
4.3 Attach ILite 3 tiles on top of each other.............................................................................................23
4.4 Attach ILite 3 tiles next to each other ............................................................................................... 24
4.5 Join two ILite 3 truss beams together. . . ............................................................................................25
4.6 Attach the ILite 3 truss beam with an ILite 3 tile. . . .................................................................................25
4.7 Securing an ILite 3 rental truss beam...............................................................................................26
4.8 Join two ILite 3 feet together . . . . .................................................................................................... 27
4.9 Install ILite 3 feet on foot beams .................................................................................................... 28
4.10 Attach ILite 3 tiles to an ILite 3 foot. ................................................................................................29
4.11 Installing a stacker system on a floor mounted ILite 3 display . . . ..................................................................30
4.12 Installing a stacker system on a hanging ILite 3 display ........................................................................... 32
4.13 Build up a floor mounted ILite 3 display ............................................................................................35
4.14 Build up a hanging ILite 3 display with truss beams. . . ............................................................................. 37
5. Cabling of an ILite 3 display.....................................................................................41
5.1 ILite 3 tile connectivity . . . ...........................................................................................................41
5.2 Power cabling of an ILite 3 display.................................................................................................. 41
5.3 Data cabling of an ILite 3 display ...................................................................................................43
6. Servicing............................................................................................................45
6.1 ILite 3 tile diagnostic. . ............................................................................................................... 45
Index......................................................................................................................47
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006 1
Table of contents
2 R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
1. Safety
1. SAFETY
1.1 Safety guidelines
Personal protection
Image 1-1
Warning
Image 1-2
Suspended loads
Image 1-3
Hard hat
Image 1-4
Mind your fingers
Be aware of suspende
d loads, wear a hard hat to reduce the risk of personal injury. Mind your fingers while working with heavy
loads.
Installation personnel
This installation must be performed by authorized and qualified technical personnel only.
Accredited safety officers must ensure the safety of the site, construction, assembly, connection, use, dismantling, transport etc. of
such safety cri
tical systems.
Caution
Installation should be performed only after you are thoroughly familiar with all of the proper safety checks and installation instructions.
To do otherwise increases the risk of hazards and injury to the user.
Assembly parts are designed for intended use only in conjunction with Barco LED walls.
Do not modify and/or replicate any component. Barco uses specific materials and manufacturing processes in order to achieve part
strength. Consult Barco for assistance with custom applications.
Always follow Barco installation instructions. Contact Barco if you should have any question regarding the safety of an application.
The manufacturer assumes no liability for incorrect, inadequate, irresponsible or unsafe assembly of systems.
Product care
Structural & mounting components should be kept dry, clean, lubricated (only if recommended), coated properly, and otherwise
maintaine
d in a manner consistent with part design. Barco products must be used in a manner consistent with their design and
inspected on a routine basis for security, wear, deformation, corrosion and any other circumstances that may affect the load handling
capability of the part.
Barco recommends inspections at regular intervals for all installations and increasing in frequency for more critical installations. If
a part is found to have damage, which may cause a decrease in load capability, the part must be removed for service or replaced
immediately.
Under no circumstances are Barco parts repairable by anyone other than Barco.
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
3
1. Safety
1.2 Important safety instructions
Instructions:
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the manufacturer
for further advice should any doubts exist regarding any cleaning procedure.
• Do not block ventilation openings. Install in accordance with the manufacturers instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets/plugs are damaged
then replacement of the defective parts must be undertaken immediately.
• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus. Replace damaged power/data cords immediately.
• Only use attachments/accessories specified by the manufacturer.
• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning protection. Unplug this
apparatus when unused for long period of time.
• Always unplug appliance from electrical outlet before cleaning or servicing.
• Refer all servicing to qualified service technicians/personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, the apparatus does not operate normally, or has b
een dropped.
• Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use caution during lifting/moving
or transporting to avoid damage by possible tipping.
4
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
1. Safety
1.3 Important warnings
Important warnings:
• Risk of electric shock:
Image 1-5
Risk of electrical shock
Risk of electric shock. Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable
parts inside. Refer servicing to qualified service personnel.
The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk
of electrical shock to persons.
The exclamation point within a triangle is intended to tell the user that imp
ortant operating and/or servicing instructions are
included in the technical documentation for this equipment.
• Maximum ambient temperature:
The maximum ambient temperature for the LED wall is 40 °C, the minimum temperature is +0 °C.
• High leakage current:
The combination of multiple tiles in an installation results in increased levels of leakage current. In order to avoid risk of electric
shock due to high leakage current, proper grounding of the installation is requ
ired.
• Flammable materials:
Keep flammable materials away from the installation (such as curtains). A lot of energy is transferred into heat. The installation
should be such that the amount of air flow required for safe operation of the equipment is not compromised. Proper ventilation
must be provided.
• ESD and LED’s:
LED components used in ILite devices are ESD (Electro-Static Discharg
e) sensitive. To prevent the possibility of destroying
LED components do not touch either in operation or while switched off.
• Risk of electric shock / Risk of fire:
To protect against risk of fire by overloading of power cables, the amount of ILite 3 tiles per power source cable is limited
depending on the used power net. A power source cable connected with a 230V power net and protected with 16A circuit
breakers can maximum provide 33 ILite 3 tiles with power. For a 190V power net is this maximum 27 tiles. Each power source
cable should be protected by a 16A rated circuit breaker.
Furthermore, the current that flows from tile to tile via the power/data linking blocks may not exceeds nine (9) ampere. Therefore,
the maximum amount of ILite 3 tiles in one column connected with the same power source cable is limited to 23 tiles in case of
a 230V power net. For a 190V power net is the maximum limit 19 tiles.
• Disconnect device:
When the appliance inlets of the individual tiles are not accessible, the socket outlets supplying the rack shall be installed near
the equipment and be easily accessible, or a readily ac
cessible general disconnect device shall be incorporated in the fixed
wiring.
• This equipment MUST be earthed:
In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the
grounding type plug will expose you to the risk of electric shock.
• Power system:
It is recommended to use a TN-S power distribution syste
m (a power distribution system with a separate neutral and grounding
conductor) in order to avoid large ground currents loops due to voltage differences in the neutral conductor. The total electrical
installation should be protected by an appropriate rated disconnect switch, circuit breakers and Ground Fault Current Inter-
rupters. The installation shall be done accord
ing to the local electrical installation codes. In Europe special attention should be
given to EN 60364, the standard for electrical installation of buildings. In Germany VDE 0100 should be adhered to.
• Mains cords:
The power cords delivered with this system have special properties for safety. They are not user serviceable. If the power cords
are damaged, replace only with new ones. Never try to repair a power cord.
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
5
1. Safety
6 R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
2. System Overview
2. SYSTEM OVERVIEW
Overview
• Introduction
• ILite 3 display tiles
• ILite 3 flight case for 24 tiles
• ILite 3 setup accessories
• Cables for ILite 3 displays
• Power boxes
• Digitizer
• Fiberlink system
• Control software
2.1 Introduction
Fundamental elements of an ILite 3 display system
• ILite 3 display tiles.
• ILite 3 feet or ILite 3 truss beams.
• ILite 3 stacker system for base stand or for hanging ILite 3 display system.
• Mono phase power box.
• Digitizer.
• Control software.
Block diagram of an ILite 3 display system
Sources Digitizer
Control
PC
Power
box
RS232
Tile 1
LED-wall
Tile 2
Tile 3
Image 2-1
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006 7
2. System Overview
2.2 ILite 3 display tiles
2.2.1 Introduction
ILite 3
The Barco I3 tile is an indoor 3,5 mm resolution, full color display tile. The ILite 3 modular concept makes it possible to build displays
with extreme sizes and shapes. The housing of the ILite 3 is provided with fast setup mechanism for easy installation. The ILite 3
can be used in a base stand or hanging display configuration. Depending on this configuration a different stacker syste
m is required.
Image 2-2
Order info
Article No. Description
R9004031 ILite 3 display tile
2.2.2 ILite 3 specifications
Specifications
Contrast ratio 950: 1(500lux)
Weight
4.8 kg (10.6 lbs)/tile
96 kg/m² (19.6 lbs/ft²)
Hor. viewing angle
145° + (min. 50% brightness)
Vert. viewing angle
145° + (min.
50% brightness)
Tile dimens
ions
Width: 258mm (10.16")
Height: 193,5mm (7.62")
Depth: 98,68mm (3.89")
Pixel pitch 3,5 mm
Brightness 1200 NIT
LED configura
tion
3-in-1 SMD
Lifetime 45 000h (50% brightness)
Colors
4,4 trillion
Refresh rate
800 Hz
Temperature ran
ge
operating:
0-40°C(32-104°F)
storage:
-20 - 60°C (-4 - 140°F)
8 R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
2. System Overview
Humidity operating:
0 - 85%
storage:
0 - 90%
Source compatibility S-Video, Composite, YUV, RGB, SDI, HDSDI, Data DVI up to SXGA
Certifications UL-CE-TUV-FCCClassA
Calibrated Brightness
1000 NIT
Screen size
Unlimited
Power consumption
120W/tile (max)
45W/tile (average)
Processing color: 14 bit
grey scale: 8 bit
2.2.3 ILite 3 dimensions
Dimensions
258 mm 98,68 mm
193,5 mm
213,25 mm
277,75 mm
Image 2-3
2.3 ILite 3 flig
ht case for 24 tiles
2.3.1 Introduction
Flight case
This fligh
t case can secure 24 ILite 3 tiles. The ILite 3 tiles are grouped in 6 assemblies of 2 x 2 inside the flight case. The assemblies
are placed in a shock absorbing frame inside the flight case. The flight case has “easy tipping” and “easy stacking” features. Four
castor wheels, of which two are provide with breaks, and eight large handles, two per side, makes the flight case easy to handle.
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
9
2. System Overview
Image 2-4
CAUTION: Maximum stack two (2) flight cases high. Never higher.
Order info
Article No. Description
R9852323
ILite 3 flight case for 24 tiles (6 tile assemblies of 2 x 2).
2.3.2 Flight case dimensions
Dimensions
1120 mm
6
8
7
m
m
640 mm
Image 2-5
10 R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
2. System Overview
2.4 ILite 3 setup accessories
Base stand setup accessories
A
B
G
F
D
C
E
Image 2-6
A ILite 3 foot beam of 2,4 meter length.
B ILite 3 foot beam of 1,2 meter length.
C ILite 3 dual foot.
D ILite 3 stacker positioning pin for ILite 3 tile.
E ILite 3 base stand stacker foot.
F ILite 3 base stand stacker profile.
G ILite 3 triple foot.
Truss setup accessories
G
C
F
D
E
B
A
H
Image 2-7
A ILite 3 dual truss beam.
B ILite 3 truss stacker f
ixation part.
C ILite 3 truss stacker profile.
D Cotter pin.
E ILite 3 truss stack
er lock pin.
F ILite 3 truss stacker connection.
G ILite 3 stacker positioning pin for ILite 3 tile.
H ILite 3 triple
truss beam.
Order info
Article No. Description
R9852310 ILite 3 Dual truss beam.
R9852311 ILite 3 Triple truss beam.
R9852312
ILite 3 Dual foot.
R9852321
ILite 3 Truss stacker profile with connection part.
R9852420
ILite 3 Base stand stacker foot.
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006 11
2. System Overview
Article No. Description
R9852322
ILite 3 Base stand stacker profile.
R9852325
ILite 3 Foot beam of 1,2 meter length.
R9852326
ILite 3 Foot beam of 2,4 meter length.
2.5 CablesforILite3displays
2.5.1 Power cables
General
Depending on the size and configuration of the ILite display several sizes and types of power cables are required.
Order info:
Article No. Description Image
R9852151
One ILite 3 power/data linking block.
Used to distribute power and data fr
om one tile to another tile.
image 2-8
R9852150
Package with 5 ILite 3 power/data linking blocks.
Used to distribute power and data from one tile to another tile.
image 2-8
R98521510
Package with 10 ILite 3 power/data linking blocks.
Used to distribute power and data fr
om one tile to another tile.
image 2-8
R9852140
ILite 3 power linking cable (C14 straight style / C13 straight style) 3,5 meter.
Used to distribute power from one tile to another tile.
image 2-9
R9852130
One ILite 3 power linking cable (C20 / C19 / C13 straight style).
Used to split up the power, coming fr
om the power source cable, into several power
columns.
image 2-10
R9852135
Package with 5 ILite 3 power linking cables (C20 / C19 / C13 straight style).
Used to split up the power, coming from the power source cable, into several power
columns.
image 2-10
R98521310
Package with 10 ILite 3 power linking cables (C20 / C19 / C13 straight style).
Used to split up the power, coming from the power source cable, into several power
columns.
image 2-10
R9851160
ILite power source cable (CEE / C19) 2,5 meter.
Use to distribute power directly from the wall outlet to a ILite 3 tile.
image 2-11
R9851170
ILite power source cable (CEE / C19) 4 meter.
Used to distribute power directl
y from the wall outlet to a ILite 3 tile.
image 2-12
R9851180
ILite power extension lead (C20 / C19) 1,5 meter.
image 2-13
R9851190
ILite power extension lead (C20 / C19) 2,5 meter.
image 2-14
R9851200
ILite power extension lead (C20 / C1
9) 4 meter.
image 2-15
12 R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
2. System Overview
Image 2-8 Image 2-9 Image 2-10
Image 2-11 Image 2-12 Image 2-13
Image 2-14 Image 2-15
2.5.2 Data cables
General
Depending on the size and configuration of the ILite display several sizes and types of data cables are required.
Order info:
Article No. Description Image
R9851211
DVI-DVI data cable of 0,9 meter (screw type plugs).
Used to link data from ILite tile to ILite tile.
image 2-17
R9851213
Package with 5 DVI-DVI data cables of 0,9 meter (screw type plugs).
Used to link data from ILite tile to ILite tile.
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006 13
2. System Overview
Article No. Description Image
R9851214
Package with 10 DVI-DVI data cables of 0,9 meter (screw type plugs).
Used to link data from ILite tile to ILite tile.
R9851680
Package with 10 white DVI-DVI data cables of 0,9 meter (screw type plugs).
Used to link data from ILite tile to ILite tile.
image 2-18
R9851210
DVI-DVI data cable of 5 meter (screw type plugs).
Used to link data from D320 Digitizer to ILite tile.
image 2-19
Image 2-16 Image 2-17 Image 2-18
Image 2-19
2.6 Power boxes
General
Depending on the size of the ILite display system, the power system has to be adapted. Therefore several sizes of power boxes are
available. For small and medium size ILite display systems the “Mono Phase Power Box” is used. For larger ILite display systems
the
re is a range of “Custom Power Boxes”. There is also a “Rental Power Box” available. Refer to the manual of the power box
used in the application for more information.
2.
7
Di
gitizer
General
The digitizer processes (image processing, conversion and conditioning) all source signals for digital distribution to every tile. The
digitizer may be accessed directly or via the control software (e.g. Director toolset). This software is designed as a user interface
to be used in conjunction with the digitizer and display. This can be used when connected to the digitizer through a serial RS232
connection. Refer to the manual of the digitizer for more information about the digitizer.
14
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
2. System Overview
2.8 Fiberlink system
General
The data signal coming out of the digitizer is carried from the digitizer to the display by a high-speed data link. To send such a high
density stream of data over long distances, a fiber optic cable is required. Barco offers a complete system: a transmitter, a cable
and a receiver.
Barco offers two different fiberlink systems: one for shorter distances, based on a multi mode optical fiber, and one for longer dis-
tances, based on a single mode optical fiber. Refer to the manual of the fiberlink system for more information about the fiberlink
system.
2.9 Control software
General
The control software is designed as a graphic user interface (GUI) and can be used to control and configure the digitizer as well as
the Barco LED wall via a PC (e.g. Director toolset). For more information refer to the manual of the control software.
R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
15
2. System Overview
16 R5976695 ILITE 3 DISPLAY SYSTEM 27/04/2006
/
