SP-20
Installation manual
R59770294/02
11/02/2009
Barco nv Media & Entertainment Division
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.883.86
E-mail: [email protected]
Visit us at the web: www.barco.com
Printed in China
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or merchantability and fi tness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not other
wise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense
Guaran tee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications
or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are
system failures which are attributed to programs or s
pecial electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by
the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
Table of contents
TABLE OF CON TENTS
1. Safety................................................................................................................ 3
1.1 Safety guidelines .................................................................................................................... 4
1.2 Important safety instructions ........................................................................................................ 5
1.3 Important warnings .................................................................................................................. 6
2. Installation requirements ........................................................................................ 7
2.1 Mechanical requirements. . .......................................................................................................... 8
2.2 Electrical requirements .............................................................................................................. 9
2.3 System requirements for the Control software . ....................................................................................10
3. Components of the SP-20 display..............................................................................11
3.1 Foot system..........................................................................................................................12
3.2 SP-20 tile ............................................................................................................................14
3.3 Soft cover ............................................................................................................................ 17
3.4 External handles.....................................................................................................................18
3.5 SP-20 package ......................................................................................................................19
3.6 Power boxes.........................................................................................................................20
3.7 Digitizer .............................................................................................................................. 21
3.8 Control software .....................................................................................................................23
3.9 Fiberlink system ..................................................................................................................... 24
4. Proper and safe use of the foot system.......................................................................25
4.1 Folding out the foot system into the 80° stand ..................................................................................... 26
4.2 Changing from the 80° to the 90° stand . . . . ........................................................................................ 28
4.3 Folding in the foot system...........................................................................................................30
5. Physical installation ..............................................................................................33
5.1 Securing SP-20 tiles.................................................................................................................34
5.2 Installing soft covers on gateways ..................................................................................................36
6. Cabling .............................................................................................................39
6.1 Power cabling of a SP-20 tile ....................................................................................................... 40
6.2 Data cabling of a SP-20 tile .........................................................................................................41
7. Maintenance........................................................................................................43
7.1 Cleaning SP-20 tiles.................................................................................................................44
8. Order info...........................................................................................................45
8.1 Order info ............................................................................................................................ 46
A. Dimensions ..........................................................................................................47
A.1 Dimensions of the SP-20 tile........................................................................................................48
B. Specifications of the SP-20 tile...................................................................................49
B.1 Specifications of the SP-20 tile......................................................................................................50
R59770294 SP-20 11/02/2009
1
Table of contents
2 R59770294 SP-20 11/02/2009
1. Safety
1. SAFETY
About this chapter
Read this chapter attentively. It contains important information to prevent personal injury while installing your SP-20 display. Fur-
thermore, it includes several precautions to prevent damage to the SP-20 tile. Ensure that you understand and follow all safety
guidelines, safety instructions and warnings mentioned in this chapter before installing the SP-20 display. After this chapter, addi-
tional “warnings” and “cautions” are given depending on the installation procedure. Read and follow these “warnings” and “cautions”
as well.
Overview
• Safety guidelines
• Important safety instructions
• Important warnings
R59770294 SP-20 11/02/2009
3
1. Safety
1.1 Safety g uidelines
Personal protection
WARNING: Ensure you understand and follow a ll the safety guidelines, safety i nstructions, warnings and
cautions mentioned in this m anual.
WARNING: Be careful w hile working with heavy loads.
WARNING: Mind your fingers wh ile working with heavy loads.
Installation personnel
This installation must be performed by authorized and qualified technical personnel only.
Accredited safety officers must ensure the safety of the site, construction, assembly, connection, use, dismantling, transport etc. of
such safety critical systems.
Caution
Installation should be performed only after you are thoroughly familiar with all of the proper safety checks and installation instructions.
To do otherwise increases the risk of hazards and injury to the user.
Assembly parts are designed for intended use only in conjunction with SP-20 LED displays.
Do not modify and/or replicate any component. Barco uses specific materials and manufacturing processes in order to achieve part
strength. Consult Barco for assistance with custom applications.
Always follow Barco installation instructions. Contact Barco if you should have any question regarding the safety of an application.
The manufacturer assumes no liability for incorrect, inadequate, irresponsible or unsafe assembly of systems.
Product care
Structural & mounting components should be kept dry, clean, lubricated (only if recommended), coated properly, and otherwise
maintained in a manner consistent with part design. Barco products must be used in a manner consistent with their design and
inspected on a routine basis for security, wear, defor
mation, corrosion and any other circumstances that may affect the load handling
capability of the part.
Barco recommends inspections at regular intervals for all installations and increasing in frequency for more critical installations. If
a part is found to have damage, which may cause a decrease in load capability, the part must be removed for service or replaced
immediately.
Under no circumstances are Barco parts repairable by anyone other than Barco.
4
R59770294 SP-20 11/02/2009
1. Safety
1.2 Important safety instructions
Instructions:
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the manufacturer
for further advice should any doubts exist regarding any cleaning procedure.
• Do not block ventilation openings. Install in accordance with the manufacturers instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets/plugs are damaged
then replacement of the defective parts must be undertaken immediately.
• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus. Replace damaged power/data cords immediately.
• Only use attachments/accessories specified by the manufacturer.
• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning protection. Unplug this
apparatus when unused for long period of time.
• Refer all servicing to qualifi ed service technicians/personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, the apparatus does not operate normally, or has been dropped.
• Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use caution during lifting/moving
or transporting to avoid damage by possible tipping.
R59770294 SP-20 11/02/2009
5
1. Safety
1.3 Important warnings
Important warnings:
Risk of electric shock:
Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing
to qualified service personnel.
Maximum and minimum am bient tem perature:
The maximum ambient temperature for the LED wall is 50 °C, the minimum temperature is -35 °C.
High leakage current:
The combination of multiple tiles in an installation results in increased levels of leakage current. In order to avoid risk of electric
shock due to high leakage current, proper grounding of the installation is required.
Flammable materials:
Keep flammable materials away from the installation (such as curtains). A lot of energy is transferred into heat. The installation
should be such that the amount of air flow required for safe operation of the equipment is not compromised. Proper ventilation must
be provided.
Risk of electric sho ck / Risk of fire:
To protect against risk of fire by overloading of power cables, MAXIMUM 6 (six) tile may be connected per power source cable. Each
power source cable should be protected by a circuit breaker or fuses rated 16 A / 250 VAC (15 A / 250 VAC in the USA and Canada).
Note that one SP-20 tile requires 200-240 VAC, 50–60 Hz, 6.5 amps at 230 VAC.
Disconnect d evice:
When the appliance inlets of the individual tiles are not accessible, the socket outlets supplying the rack shall be installed near the
equipment and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
This equipm ent MUST be earthed:
In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the grounding
type plug will expose you to the risk of electric shock.
Power sys tem:
It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding
conductor) in order to avoid large ground current loops due to voltage differences in the neutral conductor. The total electrical
installation should be protected by an appropriately rated disconnect switch, circuit breakers, over voltage protector and Ground Fault
Current Interrupters. The installation shall be done according to the local electrical installation codes. In Europe special attention
should be given to EN 60364, the standard for electrical installation of buildings. In Germany VDE 0100 should be adhered to. In
America, special attention should be given to the National Electrical Code, ANSI/NFPA 70.
Mains cords:
The power cords delivered with this system have special properties for safety. They are not user serviceable. If the power cords are
damaged, replace them only with new ones. Never try to repair a power cord.
Data cables:
The data cables provided with this system have special properties for safety. They are not user serviceable. If the data cables are
damaged, replace them only with new ones. Never try to repair a data cable. Per requirements of the National Electrical Code®
in the USA , the length of a data cable must not exceed 42 m (140 feet). Avoid exposure of data cables to accidental contact with
lightning or power conductors.
6
R59770294 SP-20 11/02/2009
2. Installation requirements
2. INSTALLATION REQUIREMENTS
About this chapter
This chapter enumerates the mechanical requirements to install the SP-20 display, the electrical requirements to power up the SP-20
display and the system requirements to efficiently run the control software for the SP-20.
Overview
• Mechanical requirements
• Electrical requirements
• System requirements for the Control software
R59770294 SP-20 11/02/2009
7
2. Installation requirements
2.1 Mechanical requirements
About the SP-20 sports perimeter
To install the SP-20 sports perimeter, Barco designed as special foot system which can be installed on every surface.
To connect the SP-20 tiles to each other, the foot system is equipped with locks which can be operated by hand or foot so no tools
are required to install the SP-20 sports perimeter.
1
2
1
2
Image 2-1
WARNING: Make sure that neig hboring tiles are always firmly secu red with both locks. (see "Foot system",
page 12)
WARNING: M ake sure that both side of gateways in the SP-20 sports perimeter are always p rovided with a
soft cover. (see "Soft cover", page 17)
8 R59770294 SP-20 11/02/2009
2. Installation requirements
2.2 Electrical requirements
Power requirements
One SP-20 tile requires 200-240 VAC, 50–60 Hz, 6.5 amps at 230 VAC. Note that one SP-20 tile contains two input/output compart-
ments. The power is linked via an external cable from the first compartment to the second. The power output port of the second
compartment must be provided with a dummy power plug. A power source cable has to be plugged into the power input port of the
first compartment. Connect MAXIMUM 6 (six) tile per power source cable.
Every power source cable should be protected by a circuit breaker or fuses rated 16 A / 250 VAC (15 A / 250 VAC in the USA and
Canada).
Barco provides a range o f power boxes, which meet the requirem ents of your SP- 20 disp lay. Contact Barco
for more information about power boxes and power requirements for your SP-20 display.
Power sys tem:
It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding
conductor) in order to avoid large ground current loops due to voltage differences in the neutral conductor. The total electrical
installation should be protected by an appropriately rated disconnect switch, circuit breakers, over voltage protector and Ground Fault
Current Interrupters. The installation shall be done according to the local electrical installation codes. In Europe special attention
should be given to EN 60364, the standard for electrical installation of buildings. In Germany VDE 0100 should be adhered to. In
America, special attention should be given to the National Electrical Code, ANSI/NFPA 70.
Disconnect d evice:
When the appliance inlets of the individual tiles are not accessibl
e, the socket outlets supplying the rack shall be installed near the
equipment and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
This equipm ent MUST be earthed:
In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the grounding
type plug will expose you to the risk of electric shock.
R59770294 SP-20 11/02/2009
9
2. Installation requirements
2.3 System requirements for the Control software
Before you begin
It is assumed you are familiar with the Windows operating system at your site.
The CD-ROM in your package contains a Windows-based installation program. You can install the software from the CD-ROM.
System requirements
Minimum specifications :
• Hardware
- PC Pentium III or equivalent, 2 GHz
- 512 Mb RAM
- Free hard disk space: 300 Mb
- XGA resolution (1024 x 768)
- Serial communication port
- Ethernet connection
• Software
- Windows 2000
1
, Windows XP Home or Windows XP Professional
Recommended specifications :
• Hardware
- PC Pentium IV or equivalent, 2.4 GHz
-1GbRAM
- 300 Mb hard disk free space
- SXGA resolution (1280 x 1024) with 32 Mb video memory
- Serial communication port
- Ethernet connection
• Software
- Windows XP Professional or Windows Vista
1. It runs on Windows 2000 but when problems are discovered, Barco does not deliver any support
10 R59770294 SP-20 11/02/2009
3. Components of the SP-20 display
3. COMPONENTS OF THE SP-20 DISPLAY
About this chapter
This chapter describes the typical components and accessories used in the SP-20 display in more detail. For other commonly used
components in Barco LED displays like power boxes, digitizer, fiberlink, compact link and control software, we refer to the manual
of these components for more information about use and installation.
Block diagram of the SP-20 display
Digitizer
Control
PC
Power
box
Sources
SP-20
tile
SP-20
tile
SP-20
tile
SP-20
tile
SP-20
tile
SP-20
tile
Image 3-1
Overview
• Foot system
•SP-20tile
• Soft cover
• External handles
• SP-20 package
• Power boxes
• Digitizer
• Control software
• Fiberlink system
R59770294 SP-20 11/02/2009
11
3. Components of the SP-20 display
3.1 Foot system
Introduction
One SP-20 tile is provided with one foot system. Each foot system consist of parts: a left foot and a right foot. When looking from
the back side of the SP-20 tile, you can notice that the right foot is equipped with 2 locks. These locks are used to connect two
neighboring tiles.
Image 3-2
Why need a foot system?
For optimal view upon the SP-20 sports perimeter, the foot system can provide two different angles of inclination (80° or 90°).
10
o
Image 3-3
12 R59770294 SP-20 11/02/2009
3. Components of the SP-20 display
How does the foot system work?
Flap down both feet by pulling the top of the profile indicated with number 1. The counterweight, indicated with number 2, makes
sure that both feet fall down and are ready to be positioned in the 80° or 90° position.
1
1
2
Image 3-4
WARNING: Read the installation procedure an d safety tips mentioned in this man ual on how to operate the
foot syst em. see chap ter "4 . Proper and safe u se of the foot system", "Proper and safe use of the foot system",
page 25
R59770294 SP-20 11/02/2009 13
3. Components of the SP-20 display
3.2 SP-20 tile
Introduction SP-20 tile
The SP-20 tile has an IP65 rated housing which can easily be lifted by two persons. The foot system enables the adjustment of the
tile tilt (10°) without tools. Furthermore, this foot system can be folded up to reduce the volume of the tile for transportation.
The LED side of the SP-20 tile is equipped with soft shaders, to prevent injury, and can easily be replaced in case of damage.
10
o
Image 3-5
Part location of the SP-20 til e
1
2
5
810
4
3
6
1112 9 7
20
13
19
17
15
14
16
18
Image 3-6
14 R59770294 SP-20 11/02/2009
3. Components of the SP-20 display
1. Mounting pin for the foot system.
2. Upper lock of the right door.
3. Door hinge.
4. Door handle.
5. Lower lock of the right door.
6. Mounting pin for the foot system.
7. Air inlet.
8. Air inlet.
9. Power and data Input/Output ports of the controller/re-sync unit.
10. Air inlet.
11. Air inlet.
12. Mounting pin for the foot system.
13. Lower lock of the left door.
14. Door handle.
15. Carrying handle.
16. Air outlet.
17. Air outlet.
18. Upper lock of the left door.
19. Mounting pin for the foot system.
20. Replaceable shaders.
Part location of the SP-20 tile with foot system
1
2
3
4
6
7
8
5
Image 3-7
R59770294 SP-20 11/02/2009 15
3. Components of the SP-20 display
1. Top connection point.
2. Top lock.
3. Mounting point for the foot system. Every foot is mounted on 2 points.
4. Spring.
5. Counterweight
6. Bottom lock
7. Counterweight.
8. Bottom connection point.
Power cables used between SP-20 tiles
To meet the demands of each SP-20 application, Barco offers several lengths of power cables to link power from tile to tile. Note
that the power output port of the last tile in the power chain has to be sealed with a dummy power plug.
Image 3-8
Power link cable of 1,5 meter (R9850241).
Image 3-9
Power link cable of 4,5 meter (R9850250).
Image 3-10
Power link cable of 9 meter (R9850260).
Image 3-11
Dummy power plug (R9850280).
Data cables used between SP-20 tiles
To meet the demands of each SP-20 application, Barco offers several lengths of data cables to link data from tile to tile. Note that
the data output port of the last tile in the power chain has to be sealed with a dummy data plug.
Image 3-12
Data linking cable of 1,5 meter (R9850210).
Image 3-13
Data linking cable of 5 meter (R9850220).
Image 3-14
Dummy data plug (R9850270).
16 R59770294 SP-20 11/02/2009
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco SLite 10 XP Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Design House 701961 Operating instructions
-
Microtek Medi-7000 User manual
-
MotorDeck G90024GRPH Installation guide
-
CSI Fiberlink Matrix Operating instructions
-
-
Cutler-Hammer D320 PLC User manual
-
-
-
-
