Extron Extender MK User manual

Brand: Extron

Model: Extender MK

Type: User manual

Extender Series

VGA-UXGA Line Drivers with Audio

Extender

Series User

Guide

68-552-01 Rev. M

01 19

User Guide

Distribution Ampliﬁers

Important Information

Safety Instructions

Safety Instructions • English

WARNING: This symbol, ,when used on the product, is

intended to alert the user of the presence of uninsulated dangerous

voltage within the product’s enclosure that may present a risk of electric

shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)

instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron

website, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses

Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und

die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in

den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del

producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y

mantenimiento recogidas en la documentación proporcionada con el

equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad

de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du

produit d’une tension électrique dangereuse susceptible de provoquer

un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance

importantes qui se trouvent dans la documentation fournie avec le

matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la

réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets

connexes, lisez les informations de sécurité et de conformité Extron, réf.

68-290-01, sur le site Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa

all’interno del contenitore del prodotto che può costituire un rischio di

scosse elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di importanti istruzioni di funzionamento

e manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,

compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento

alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo

68-290-01, sul sito web di Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego

napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie

porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji

(obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji

wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,

zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część

numer 68-290-01, na stronie internetowej Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению электрическим

током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций

по эксплуатации и обслуживанию в руководстве,

прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других

вопросах см. руководство по безопасности и соблюдению

нормативных требований Extron на сайте Extron: ,

www.extron.com, номер по каталогу - 68-290-01.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍

使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01。

安全記事 • 繁體中文

警告: 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資

訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規

遵守手冊》，準則編號 68-290-01。

安全上のご注意 • 日本語

警告: この記号が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守(整備)の指示についてユーザーの注意

を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に

ついては、エクストロンのウェブサイト www.extron.com より『 Extron Safety

and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을

경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에

대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및

규제 준수 안내서, 68-290-01 조항을 참조하십시오.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks

(®)

, registered service marks

(SM)

, and trademarks

(™)

are the property of RGB Systems, Inc. or

Extron Electronics (see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(®)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Glitch Free, GlobalConﬁgurator,

GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort,

NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(™)

AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS (ClassD

Ripple Suppression), Codec Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), DriverConﬁgurator,

DSPConﬁgurator, DSVP (Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, FOX, FOXBOX, IPIntercom HelpDesk, MAAP,

MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC (QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink,

SIS, SimpleInstructionSet, Skew-Free, SpeedNav, Triple-Action Switching, True4K, Vector

™

4K, WebShare, XTRA, and ZipCaddy

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference. This interference must be corrected at the expense of the user.

NOTE: For more information on safety guidelines, regulatory compliances,

EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and

Regulatory Compliance Guide” on the Extron website.

Battery Notice

This product contains a battery. Do not open the unit to replace the battery. If the battery

needs replacing, return the entire unit to Extron (for the correct address, see the Extron

Warranty section on the last page of this guide).

CAUTION: Risk of explosion. Do not replace the battery with an incorrect type. Dispose

of used batteries according to the instructions.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.

Débarrassez-vous des piles usagées selon le mode d’emploi.

Conventions Used in this Guide

Notiﬁcations

The following notiﬁcations are used in this guide:

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessure mineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

NOTE: For commands and examples of computer or device responses mentioned

in this guide, the character “0” is used for the number zero and “O” is the capital

letter “o.”

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and ﬁeld names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product speciﬁcations are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

IPCP Pro Series • Contents vii

Contents Contents

Reference Information ...............................18

Dimensions....................................................... 18

Extender AAP and Extender AAP EX

Dimensions .................................................. 18

Extender WM Dimensions ............................. 19

Extender WM AAP Dimensions ..................... 20

Extender WM AUS Dimensions ..................... 20

Extender MK Dimensions.............................. 21

Extender AKM UK Dimensions ..................... 21

Extender AKM MAAP Dimensions ................ 22

Extender D Dimensions ................................ 23

Cut-out Templates ............................................ 24

Extender WM Template ................................. 24

Extender WM AAP Template ......................... 25

Extender MK Template.................................. 26

Extender WM AUS Template ......................... 27

Introduction ...................................................1

About this Guide ................................................. 1

About the Extender Series VGA Line Drivers ....... 1

Differences Between the Models ..................... 1

Features ......................................................... 2

Installation ..................................................... 3

UL Guidelines ..................................................... 3

Installation Instructions ....................................... 3

Preparing the Site and Installing the Wall Box ..... 4

Considerations ............................................... 4

Procedure ....................................................... 4

Front Panel Features

and Cabling ....................................................... 7

Top, Rear, Bottom Panel Features and Cabling . 10

Mounting .......................................................... 13

Mounting the Extender AAP or

Extender AAP EX into an AAP Wallplate or

Device Faceplate ......................................... 13

Pre-installation Testing and Troubleshooting .. 14

Mounting the Extender WM or

Extender WM AAP to the Wall Box .............. 15

Mounting the Extender D .............................. 15

Mounting the Extender MK to the

Knockout Box.............................................. 16

Application Diagrams ........................................ 16

IPCP Pro Series • Contents viii

Extender Series • Introduction 1

Introduction

This chapter covers the following topics:

• About this Guide — covers the scope of this guide and the terminology used in it

• About the Extender Series VGA Line Drivers— a description of the products, what

they do and how they differ

About this Guide

This guide contains information about the Extron Extender Series line drivers and on how

to operate and conﬁgure them. “Extender” and “line driver” are used to refer to all models

interchangeably when instructions apply to more than one model.

About the Extender Series VGA Line Drivers

The Extron Extender Series are one-input VGA-UXGA line drivers with audio. There are

seven models in the series:

• Extender AAP

• Extender AAP EX

• Extender WM

• Extender D

• Extender WM AAP

• Extender MK

• Extender AKM MAAP.

They boost the video signal between a laptop or desktop computer and a monitor or

projector. Each has a 300 MHz (-3 dB) video bandwidth.

Each line driver accepts one computer-video input and one stereo audio input. Each

Extender also features one buffered VGA-type RGB output and one stereo audio output.

With an optional Mac/VGA adapter, the Extender can also buffer signals from a Macintosh

computer.

Differences Between the Models

All Extender models are functionally identical but they have different mounting options.

For details about mounting the Extender AAP, Extender WM, Extender D,

Extender WM AAP, and the Extender MK, see Preparing the Site and Installing the Wall

Box starting on page4 in the installation section.

For Extender AAP EX mounting instructions, see the user guide or installation guide for the

appropriate model of Extron HSA Hideaway Surface Access enclosure.

For Extender AKM MAAP mounting instructions, see the Extender AKM MAAP Installation

Guide, available at http://www.extron.com.

Extender Series • Introduction 2

Features

Video signal boosting — The selectable gain and peaking settings boost video signals to

compensate for signal degradation caused by long cables. The Extender can send a high

resolution signal up to 250 feet (75 m) through Extron M59 Series mini high resolution cable.

Sync restoration — Each Extender restores low level sync voltages found on many laptop

PCs (as low as two volts) to normal TTL levels.

Audio buffering — Unbalanced stereo audio inputs can be output as balanced audio for

long cable runs.

Extender Series • Installation 3

Installation

The following topics are covered in this chapter:

• UL Guidelines

• Installation Instructions

• Preparing the Site and Installing the Wall Box

• Front Panel Features and Cabling

• Top, Rear, Bottom Panel Features

• Mounting

• Application Diagrams

ATTENTION: Installation and service must be performed by authorized personnelonly.

This product should be used with a UL listed electrical box (see “UL Guidelines,”

below).

UL Guidelines

1. The Extender must be installed in an Underwriters Laboratories (UL) Listed junction

box. The UL approved electrical wall box (junction box) is not included with the unit; the

installer is responsible for obtaining and installing the box.

2. The unit must be installed with accordance with the National Electrical Code and with

local electrical codes.

Installation Instructions

Depending on the model, the Extenders can be mounted into furniture, a wall, an

Ackermann ﬂoorbox (see ackermann.co.uk), or an Extron HSA 400 Series or HSA 800

Series enclosure. Installation involves the following main steps:

1. Prepare the site, run cables, and install a wall box or ﬂoor box.

2. Cable rear panel connectors and set the gain switch.

3. Test the Extender.

4. Mount the Extender.

5. Attach input cables to the front panel.

For Extender AKM MAAP mounting instructions, see the AKM MAAP Installation Guide.

ATTENTION: The Extender must be installed in a UL listed wall box, which the installer

is responsible for obtaining.

For Extender AAP EX mounting instructions, see the user guide or installation guide for the

appropriate model of HSA Hideaway Surface Access enclosure.

NOTE: The Extender AAP EX does not require a wall box if it will be installed into an

Extron HSA 400 Series or HSA 800 Series surface access product. If you install an

ExtenderAAPEX without an HSA, you must use a wall box.

Extender Series • Installation 4

Preparing the Site and Installing the Wall Box

Considerations

Choose a location that allows cable runs without interference. Allow enough depth for both

the wall box and the cables. You may need to install the cables into the wall, furniture, or

conduits before installing the line driver.

• The Extender AAP or Extender AAP EX can be installed in an Extron two-gang, four-

gang, or half rack width AAP Architectural Adapter Plate or in the faceplate of another

Extron device that accepts AAP plates, such as an interface or distribution amplifier.

See the mounting instructions for the adapter plate or device.

• The Extender AAP EX is usually installed into an Extron HSA 400 Series or

HSA 800 Series surface access enclosure.

• The Extender WM can be installed in a standard or compact one-gang electrical wall

box. This is also true for the Extender D, though it requires a standard decorator-style

wallplate.

• The Extender WM AAP can be installed in a three-gang wall box, and its faceplate

accepts up to four single height Extron Architectural Adapter Plates (AAPs).

• The Extender MK can be mounted into a standard, shallow knockout switch box (also

known as a KO box or MK box) that is used in Singapore, the United Kingdom, and

Australia.

The installation must conform to national and local electrical codes and to the Extender’s

size requirements. Dimensional drawings and templates are provided in Dimensions

starting on page18.

Procedure

1. See the template that corresponds to the Extender model and wall box being used.

NOTE: The templates are not shown at full size. Pay attention to the

measurements shown on the templates.

2. Mark the guidelines for the opening on the wall or furniture.

• If the Extender will be installed in a wall box, place the box against the

installation surface and draw a line on it around the outside of the box.

• If the Extender will be installed without a wall box (using mud rings or

fastening it directly to the wall or furniture), measure and mark the surface for the

cutout area indicated in the template.

3. Cut out the material from the marked area.

4. Check the opening size by inserting the wall box or the Extender (if no box is used)

into the opening. The box and line driver should ﬁt easily into the opening. Adjust the

opening as needed.

5. Feed cables through the wall box punch-out holes and secure them with cable clamps

to provide strain relief.

Extender Series • Installation 5

6. Exposed cable shields (braids or foil) are potential sources of short circuits. Trim back

and insulate shields with heat shrink.

CAUTION: To prevent short circuits, the outer foil shield can be cut back to the

point where the cable exits the cable clamp. Both braided and foil shields should

be connected to an equipment ground at the other end of the cable.

Metal

Wall Bo

Screw

Braided

Shield

Install Cable

Foil Shield

Cab

le Clamp

Figure 1. Grounding Outer Braided and Foil Shields

7. Insert the wall box into the opening, and attach it to the wall, stud, or furniture.

• For the Extender WM, Extender WM AAP, Extender D, and the Extender AAP or

Extender AAP EX (if installed in a two- or four-gang AAP plate), attach the wall box

to the wall stud or furniture with nails or screws, leaving the front edge flush with the

outer wall or furniture surface. See the following illustration, which applies to one-,

two-, three-, and four-gang wall boxes.

1-gang wall box.eps

Installation Cable

Cable Clamp

Wall Stud

Installation Cab

Cable Clamp

Wall Stud

Screws or NailsScrews or Nails

Figure 2. Attaching a Wall Box to a Wall Stud

If attaching the wall box to wood, use four #8 or #10 screws or 10-penny nails.

Aminimum of ½" (1.3 cm) of screw threads must penetrate the wood.

If attaching the wall box to metal studs or furniture, use four #8 or #10 self-tapping

sheet metal screws or machine bolts with matching nuts.

Extender Series • Installation 6

• For the Extender MK, pull the mounting tabs of the knockout boxforward to secure

them against the back side of the wallboard or furniture as shown in the following

illustration.

Pull mounting tab

forward.

Figure 3. Securing the MK Knockout Box to a Wall or Furniture

8. Set the gain switch, and cable and test the line driver before fastening the line driver into

the wall box. The switch and cables will be inaccessible after installation. See

Top, Rear, Bottom Panel Features on page10 for details.

Extender Series • Installation 7

Front Panel Features

and Cabling

EXTENDER

COMPUTER IN

AUDIO IN

EXTENDER AKM MAAP

AUDIO IN COMPUTER IN

EXTENDER MK

COMPUTER IN

AUDIO IN

EXTENDER WM AUS

COMPUTER IN

AUDIO IN

EXTENDER AKM UK AAP

AUDIO IN

COMPUTER IN

EXTENDER WM AAP

AUDIO IN

EXTENDER WM

COMPUTER IN

AUDIO IN

COMPUTER IN

AUDIO IN

BC D

Faceplate screws, page7 (below)

RGB video input connector (Computer In), page8

Power and signal LED, page8

Opening for Architectural Adapter Plates (AAPs), page8

Audio input connector, page8

Opening for Mini Architectural Adapter Plates (MAAPs), page9

Faceplate screws — These screws (see figure 4,

, above) secure the faceplate to

the rest of the line driver. Faceplate dimensions are provided in the reference section of

this manual.

NOTE: Do not remove these faceplate screws or the jack screw nuts on either side

of the PC Input connector while the line driver is attached to the wall. If these

screws are removed, the detached line driver may fall down inside the wall.

Figure 4. Front Panels

Extender Series • Installation 8

To replace the standard faceplate with a customized faceplate:

1. Set the line driver in an accessible place (do not do this while

the line driver is installed in a wall or furniture), and remove

the faceplate screws and the jack screw nuts on either side of

the PC Input connector.

2. Fasten the new faceplate to the line driver with the faceplate screws.

3. Reattach the jack screw nuts.

Power and signal LED — This LED (see figure 4,

, on the previous page) lights:

• amber to indicate that the Extender is receiving power

• green to indicate that an active sync signal is present at the input and the Extender

is receiving power

NOTE: The LED remains lit amber when the input signal is HDTV component video,

RGsB, or RsGsBs.

Audio input connector — Plug a 3.5 mm stereo plug

into this jack (see figure 4,

) for unbalanced audio

input. Wire the male plug as

shown in the figure at right.

RGB video input connector (Computer In) — Attach a cable from the computer to the

Extender via this female 15-pin HD connector (see figure 4,

Opening for Architectural Adapter Plates (AAPs) — The Extender WM AAP can

have up to four optional adapter plates attached here (see figure 4,

) at one time.

The adapter plates allow for a variety of types of audio/video connectors or another

device such as the Extender AAP to be added to the faceplate.

Blank plates are included with the Extender WM AAP and Extender AKM MAAP to

cover unused spaces.

Other adapter plates must be ordered separately. They also must be attached to the

faceplate and cabled before the line driver is installed in the wall or furniture. The screws

needed for installing the adapter plates are built into the plates, so no additional screws

are needed.

1. Remove the blank plates from the Extender

by unscrewing the nuts that fasten the

plates to the faceplate.

2. Insert the adapter plate screws through the

holes in the faceplate. Attach the adapter

plates to the faceplate with the provided

captive washers and #4-40 nuts.

3. Attach the output cables to the rear

connectors of the adapter plates. Soldering

is required for some connectors. Attach foil

and braided shields to ground connections.

Jack Screw Nuts

Sleeve ( )

Ring (R)

Tip (L)

3.5 mm Ster

eo Plug Connecto

(unbalanced)

EXTENDER WM AAP

COMPUTER IN

AUDIO IN

#4-40 Nut with

Captive Washer

Extender WM AAP

(up to 4 plates)

Adapter Plate

Extender Series • Installation 9

Opening for Mini Architectural Adapter Plates (MAAPs) — The Extender AKM

MAAP can have up to three optional MAAP adapter plates attached here (see figure 4,

, page7) at one time to allow for a variety of types of audio/video connectors or

another device to be added to the faceplate.

One double-size and one single-size blank plate are included with the

ExtenderAKMMAAP to cover unused spaces. Other adapter plates must be ordered

separately. They also must be attached to the faceplate

and cabled before the line driver is installed in the wall,

floor box, or furniture. The screws needed for installing

the adapter plates are included with the MAAPs, so no

additional screws are needed.

See the picture at right and the following steps.

1. Insert the MAAP into the faceplate opening of the

Extender AKM MAAP.

2. Using an Allen wrench, secure the MAAP to the

faceplate with the provided machine screws.

Extron

Extender AKM MAAP

Line Driver

EXTENDER AKM

MAAP

COMPUTER IN

AUDIO IN

#4 - 40 Screws

Extender Series • Installation 10

Top, Rear, Bottom Panel Features and Cabling

Figure 5. Top, Rear, and Bottom Panel Features

Audio output connector, below

Power connector, page12

RGB video output connectors, page11

Gain switch, page12

Audio output connector (see figure 5,

, above) — Insert wires into and tighten the

screws on this 3.5 mm, 5-pole direct insertion captive screw connector for unbalanced

or balanced audio output. Wire the connector as shown in the illustrations on the next

page.

ATTENTION: Connect the sleeve to ground (Gnd). Connecting the sleeve to a

negative (-) terminal will damage the audio output circuits.

Extender MK, Extender AAP, Extender AAP EX, Extender WM AUS,

Extender AKM UK AAP, and Extender AKM MAAP

Top View

Extender WM, Extender WM AAP

and Extender

Rear View

Extender MK/AAP/AAP EX,

Extender AKM UK AAP,

Extender AKM MAAP,

Extender WM AUS

Rear View

Extender MK, Extender AAP, Extender AAP EX, Extender WM AUS,

Extender AKM UK AAP, and Extender AKM MAAP

Bottom View

(Side)

Extender Series • Installation 11

Extender WM AUS is shown

at right wired for

balanced audio output.

The circuit board

configuration is

the same for the

ExtenderMK,

ExtenderAAP,

Extender AAP EX,

and

Extender AKM MAAP.

Extender WM is shown below wired for balanced audio output. The circuit board

configuration is the same for the Extender WM AAP and the ExtenderD.

12 VDC

Power

Sleeve

(s)

Left Tip

Right Tip

Left Ring

Right Ring

Audio

Unbalanced Output

Left Tip

NO Ground Here

Sleeve

(s)

Right Tip

NO Ground Here

Balanced Output

Sleeve

(s)

Left Tip

Right Tip

Left Ring

Right Ring

Audio

Do not tin the wires!

CAUTION

For unbalanced audio, connect the

sleeve(s) to the ground contact.

DO NOT connect the sleeve(s)

to the negative (-) contacts.

(5 mm) max.

RGB video output connectors (see figure 5,

, page10) — Attach coaxial

cables from the Extender to the display device via these female BNC connectors. These

BNCs are on pigtail wires secured to the Extender by tie wrap.

Extender Series

12 VDC

Power

Gain

(Switch is on the lower circuit board.)

Maximum

Max. peaking

& gain

Medium – Mid-level

peaking & gain

Normal

Unity

gain

www.extron.com

33-612-02

Rev. C

2 05

Audio

Unbalanced Output

Left Tip

NO Ground Here

Sleeve(s)

Right Tip

NO Ground Here

Balanced Output

Sleeve(s)

Left Tip

Right Tip

Left Ring

Right Ring

Sleeve (s)

Left Tip

Right Tip

Left Ring

Right Ring

Audio

12 VDC

Power

(5 mm)

max.

CAUTION

For unbalanced audio, connect the

sleeve(s) to the ground contact.

DO NOT connect the

sleeve(s) to the

negative (-)

contacts.

Do not tin the wires!

Extender Series • Installation 12

Power connector (see figure 5,

, page10) — Connect a

12 VDC power supply to this 3.5 mm, 2-pole direct insertion

captive screw connector. Wire the connector as shown at right.

Polarity is not important.

ATTENTION: For best results and to reduce the risk of short circuits, trim just

3/16inch (5mm) of the jacket from the wires. Do not tin the wires.

Gain switch (see figure 5,

) —

At right: Extender MK,

Extender AAP

and

Extender AKMMAAP

gain switch location

(access from the rear)

At right: Extender WM

and Extender WM AAP

gain switch location

(access from the side)

At right: Extender D gain switch

location (like the Extender WM

switch, but accessible from the

front)

To compensate for cable resistance and capacitance, use a small screwdriver to slide

this switch to select the level of video gain that yields the sharpest, smear-free picture.

• Normal — unity gain (no signal boost)

• Medium — mid-level peaking and gain

• Maximum — maximum amount of peaking and gain. Select this for use with longer

cables.

NOTE: Adjust the gain before installing the Extender into a wall, furniture, or

equipment, as the gain switch will be inaccessible after installation.

–

12 VDC

Power

Do not tin the wires!

(5 mm) max.

Maximum

Max. peaking

and gain

Medium – Mid-level

peaking and gain

Normal

Unity

gain

Maximum

Max. peaking

& gain

Medium – Mid-level

peaking & gain

Normal

Unity

gain

Circuit

board

Faceplate

COMPUTER IN

AUDIO IN

SW1

Maximum –

Max. peaking

and gain

Medium –

Mid-level

peaking

and gain

Normal –

Unity gain

Circuit

board

Page is loading ...

Extron Extender MK User manual

Extron Extender MK User manual

Extron Extender MK User manual

Related papers

Other documents