2. Toro
  3. Trailer Light Kit, Side-Dump Mixers
Trailer Light Kit, Side-Dump Mixers

Toro Trailer Light Kit, Side-Dump Mixers Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Trailer Light Kit, Side-Dump Mixers Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3377-600RevB
TrailerLightKit
Side-DumpMixers
ModelNo.68062
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
Thisproductcontainsachemicalorchemicals
knowntotheStateofCaliforniatocausecancer,
birthdefects,orreproductiveharm.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
Bracket2
Bolt4
1
Nut4
Installthebrackets.
Wireharness1
Cableclamp
7
Edgeclip—parallel4
Edgeclip—perpendicular1
Fir-treemount2
Bolt
5
Nut
5
Cabletie
5
2
Grommet
2
Installthewires.
Light2
License-plateholder1
3
Nut4
Installthelights.
Reector
2
Bolt2
4
Nut2
Installthereectors.
5
Nopartsrequired
–
Replacethelightbulbs.
©2013—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3377-600*B
1
InstallingtheBrackets
Partsneededforthisprocedure:
2Bracket
4Bolt
4Nut
Procedure
1.Aligntheboltholesofabracketwiththeboltholesin
thesideframerailunderthecowl(Figure1).
Note:Foroldermodels,drill(2)7.5mm(9/32inch)
holesoneachsideoftheframe,spaced5.1cm(2
inches)apart,toaccommodatethe2mountingbolts
foreachbracket.
1
G020909
Figure1
1.Boltholes
2.Insertaboltthrougheachofthe2holesinthebracket
andtheframe.
3.Installanutoneachbolt.
Note:Tightenthesenutsandboltslater,when
youmountthecableclamps;refertostep4in
2InstallingtheWires(page2).
4.Repeatsteps1through3ontheothersideofthe
machine.
2
InstallingtheWires
Partsneededforthisprocedure:
1Wireharness
7
Cableclamp
4Edgeclip—parallel
1Edgeclip—perpendicular
2Fir-treemount
5
Bolt
5
Nut
5
Cabletie
2
Grommet
Procedure
Differentmodelsuseadifferentnumberoffasteners.Usethe
appropriatenumberoffastenersforyourmachine.
1.Pushthepre-installedr-treemount(
Figure2)onthe
shortbranch(withtheyellowwire)ofthewireharness
intotheholeclosesttothemachine,intheleftlight
bracket(Figure3).
G021014
Figure2
G020910
1
Figure3
1.Fir-treemount
Note:Ensurethateachsideofthewireharnessgoes
tothecorrectsideofthemachine.Ifyouswitchthe
wiringofthelights,eachturnsignalwillashonthe
wrongside.
2.Pushthepre-installedr-treemountonthelong
branch(withthegreenwire)ofthewireharnessinto
theholeclosesttothemachine,intherightlight
bracket(
Figure3).
2
3.RoutethewireharnessasshowninFigure4,Figure7,
orFigure8,dependingonthemodel.
1
2
4
4
3
4
G021626
2
Figure4
Concretemixers(frameundersideshownforclarity)
1.Edgeclip3.Wireharness
2.Excesswire
4.Cableclamp
Note:Someconcretemixers(Figure4)haveaholein
therearverticalpartoftheframe;installagrommetin
thehole,routethewireharnessthroughthegrommet,
andsecurethewireharnessbypushingar-treemount
intothesmallholeunderthegrommet(Figure5).If
yourmachinedoesnothaveahole,routethewire
harnessundertheframe,andsecureitwithanedge
clip(Figure6).
1
2
G021629
Figure5
Framewithhole
1.Holeandgrommet
2.Holeforr-treemount
3
1
G021630
Figure6
Framewithouthole
1.Edgecliplocation
1
4
2
4
3
G021627
2
Figure7
Belt-drivemortarmixers(frameundersideshownforclarity)
1.Edgeclip3.Wireharness
2.Excesswire
4.Cableclamp
4
1
2
3
4
4
G021628
Figure8
Gear-boxmortarmixer(frameundersideshownforclarity)
1.Edgeclip3.Wireharness
2.Excesswire
4.Cableclamp
4.Usecableclampsandedgeclipstosecurethewire
harnessalongtheinsideoftheframe(Figure9).
G020912
21
Figure9
1.Cableclamp
2.Edgeclip
Note:Touseacableclamp,spreaditapartandt
thewireharnessintoit.Thensqueezetheclampback
together.Fastentheclamptotheframeofthemachine
withanutandabolt,usingthepre-drilledholesalong
theframe.Tightenthenutsandboltsuntiltheyare
secure.
Foroldermodels,drilla7.5mm(9/32inch)holefor
eachbolt.
Ineachofthe2rearcornersoftheframe,useanut
andboltthatsecurethelightbrackettoalsosecurea
cableclamp(Figure10).
Note:Ensurethatyoutightenthe2nutsandbolts
foreachbracket.
G020980
1
Figure10
1.Nutandbolt
Note:Touseanedgeclip,pushitintopositionalong
theedgeoftheframeandinsertacabletiethroughthe
slot.Usethecabletietosecurethewireharness.
5.Pullthefrontendofthewireharnessoutthroughthe
holeinthefrontpostofthemachinesothatthereis
about61cm(24inches)ofslackbeyondthefrontof
theinstalledtowpole(Figure11).
Note:Foroldermodels,useaholesawtodrilla4.2
cm(1-5/8inch)holeinthefrontpostofthemachine,
sothatthewireharnessexitstheframeinlinewith
thehorizontalframerails.
5
1
2
3
G02091 1
Figure11
1.Grommet3.Cabletie
2.Fir-treemount
6.Slidethegrommetoverthe4-pinconnector(Figure12)
onthefrontofthewireharness,andinstallitinthe
holeinthefrontpost(Figure11).
G020981
Figure12
7.Pushther-treemountintothesmallholenextto
wherethewireentersthefrontpost,andinsertacable
tiethroughtheslot.
Note:Usethecabletietosecurethewireharness.
Foroldermodels,drilla7mm(17/64inch)holefor
ther-treemount.
8.Stowtheexcesswireasfollows:
•Forconcretemixers,stowtheexcesswireonthe
undersideoftheleftframerail.Usecabletiesto
securetheexcesswiretothepreviouslyinstalled
sectionofwire.
•Formortarmixers,coiltheexcesswireandbundle
itwithacabletie.Stowthebundledexcesswire
insidethecenterframerail,andsecurethebundle
withanothercabletieasnearaspossibletothe
edgeclip.
•Ifthereisexcesswirebetweentheleftlightand
therightlight,bundleitwithacabletie,andsecure
ittoapreviouslyinstalledsectionofwirewith
anothercabletie.
Important:Ensurethatanyexcesslengthinthe
wireharnessissecurewithcabletiesandwillnot
comeloose.
3
InstallingtheLights
Partsneededforthisprocedure:
2Light
1License-plateholder
4Nut
Procedure
1.Positionthelicense-plateholderontothepostsofthe
lightwiththeclearbottomlens,sothattheclearlensis
facingthelicense-plateholder(Figure13).
G020913
1
2
3
4
5
Figure13
Leftlight
1.Yellowwire—stopandturn4.License-plateholder
2.Brownwire—taillight
5.Clearlens
3.Whitewire—ground
Note:Thisistheleftlight,whichilluminatesthe
licenseplatethroughtheclearlens.
2.Installthelightsothatthepostsgointotheholesin
thebracketontheleftsideofthemachine(Figure13).
3.Installtheroundterminalofthegroundwire(white)
ontotheoutsidethreadedpost(Figure13).
4.Installthenutsontothethreadedposts;tightenthem
byhandtopreventcross-threading,thenuseawrench
tosecurethemuntiltheyaresnug.
Important:Donotovertightenthenuts,orthe
plastichousingwillbreak.
5.Pushthewiresintotheappropriateholesinthelight
(
Figure13).
Note:Ifyouneedtoremoveawirefromthelight,
inserttheendofapaperclipintothesmallholeunder
thewire,thenpullthewireout.
6.Repeatsteps2through5forthelightontheright-hand
sideofthemachine(
Figure14).
6
G020914
1
2
3
Figure14
Rightlight
1.Greenwire—stopandturn
3.Whitewire—ground
2.Brownwire—taillight
4
InstallingtheReectors
Partsneededforthisprocedure:
2
Reector
2Bolt
2Nut
Procedure
1.Aligntheholeinareectortotheholein1sideofthe
frontpostonthemachine(Figure15).
Note:Foroldermodels,drilla7.5mm(9/32inch)
holeforeachbolt.
1
G020915
Figure15
1.Reector
Note:Formodel68024,mountthereectorsonthe
triangularsupports(Figure16).
1
G020921
Figure16
Model68024
1.Reector
2.Insertaboltthroughthereectorandtheframe,and
installanutontheotherside.
3.Useawrenchontheboltandanotherwrenchonthe
nuttotightenthemuntiltheyaresnug.
Important:Donotovertightenthenutsandbolts,
ortheplasticreectorswillbreak.
4.Repeatsteps1through3fortheotherside.
7
5
ReplacingtheLightBulbs
NoPartsRequired
ReplacingtheRear-facingBulbs
Note:Theleftrear-facingbulbalsoilluminateslicenseplate.
1.Useascrewdrivertoremovethe4screwsfromthe
largesquarelensonthelight(Figure17).
A
B
C
D
E
F
G020829
Figure17
2.Removethelens(Figure17).
3.Pushandtwistthebulbcounterclockwisetoremoveit
fromthesocket(Figure17).
4.Pushanew1157bulbintothesocketandthentwistit
clockwise(Figure17).
5.Installthelensandthe4screws(
Figure17).
ReplacingtheSide-facingBulbs
1.Useascrewdrivertoremovethe2screwsfrom
thesmallrectangularlensonthesideofthelight
(Figure18).
A
B
C
D
E
F
G020830
Figure18
2.Removethelens(Figure18).
3.Pullthebulboutofthesocket(Figure18).
4.Pushanew168bulbintothesocket(Figure18).
5.Installthelensandthe2screws(Figure18).
8
/