USER MANUAL
IMMERSE
ACTIVE
WIRELESS
EARPHONES
kitsound.co.uk
JB. 5329-b / Made in China. © KitSound is a trademark of Kondor Limited, 2017. Christchurch, Dorset, BH23 4FL, UK
Warning: To prevent possible hearing damage, do not listen at high volume levels for long periods.
For your own safety, please be aware of your surroundings when using these earphones.
Not suitable for children.
Your product and batteries must be recycled or disposed of properly. Please contact your local recycling centre
for more information on proper disposal.
All trademarks are acknowledged as the property of their respective owners. Unless otherwise stated their
use does not imply that the trademark owner is aliated with KitSound or endorses the products herein.
Please recycle this packaging responsibly.
2 3
Please read this manual carefully before use.
Box contents
• KS Immerse Active Wireless Earphones
• Magnetic USB charge cable
• S/M/L earbuds
• User manual
Functions
1. Volume–/Previous track
2. LED indicator
3. Multi-function button (MFB)
4. ANC switch
5. Volume+/Next track
6. Microphone
7. Magnetic charger contact
8. Magnetic USB charger
9. Charging LED indicator
Instructions for use
Charging the battery
1. Connect the Magnetic charger contact (7) to the Magnetic USB charger (8)
2. Connect the other end of the Magnetic USB charger (8) to a PC USB port or USB mains charger
3. The Charging LED indicator (9) will be red whilst charging, and the LED will turn o when battery is full
Note: The rst charge may take up to 3 hours to complete.
Battery information
• A rechargeable battery powers your device. Unplug the charger from the electrical plug and the device
when not in use
• If left unused, a fully charged battery will lose its charge over time. We recommend a full charge twice
a month to ensure battery integrity
• Please do not leave the device in hot or cold places, such as in a closed car in summer or winter
conditions, as it will reduce the capacity and lifetime of the battery
• Do not dispose of batteries in a re as they may explode. Batteries may also explode if damaged
7
1
5
3
4
6
2
9
8
4 5
Pairing a wireless device
1. Hold the MFB (3) down for 3 seconds. You will see the LED indicator (2) rapidly ash blue and then
enter pairing mode
2. Turn on your iOS, Android, or Windows device’s Bluetooth ON and search for new devices
3. Select ‘KS Immerse Active’ from the list of found devices. If asked for a passcode, enter ‘0000’ or
‘1234’ and the earphones will then be connected to your device
4. After pairing successfully, the LED indicator (2) will slowly ash blue; you can then answer the phone
or listen to your music
5. The next time you switch the earphones on, they will automatically search for and attempt to connect
to the last paired device
Note: ‘Bluetooth’ is a trademark of Bluetooth SIG, Inc. This product is in no way aliated with or
endorsed by Bluetooth SIG Inc.
Re-pairing or pairing new devices
1. Make sure you have turned o the wireless connectivity on any previously paired devices
2. Follow the ‘Pairing a wireless device’ instructions from step 1
Functionality
Power on Hold the MFB (3) down for 2 seconds
Power o Hold the MFB (3) down for 4 seconds
To answer a call Press the MFB (3) and immediately release
To end call Press the MFB (3) and immediately release
To reject a call Press and hold the MFB (3) for 2 seconds and then release
Voice control When connected with no music playing, press and hold the MFB (3)
(not supported by all devices)
Volume+ Press and hold the Volume+/Next track (5) to increase volume
Volume– Press and hold the Volume–/Previous track (1) to decrease volume
Previous track Press and immediately release the Volume–/Previous track (1) twice
Next track Press and immediately release the Volume+/Next track (5) twice
Play/Pause Press the MFB (3) down and immediately release
6 7
Care for your Immerse Active
Please DON’T:
• Get the Immerse Active wet
• Drop the Immerse Active as this will invalidate your warranty
• Open up the Immerse Active. There are no user serviceable parts inside
• Expose the Immerse Active to extreme temperatures or rapid changes of hot to cold or vice versa
• Charge the Immerse Active if the headset/remote has got wet
Please DO:
• Clean the Immerse Active with a soft dry cloth and no detergents
Using Active Noise Cancelling
Push the ANC switch (4) to activate, and the LED indicator (2) will turn white.
Warning: We do not recommend that this product is used driving or walking as it will
prevent you from hearing warnings that could be a danger to you or others.
Note: Active Noise Cancelling will not work when battery has drained.
8 9
Troubleshooting
• If you cannot connect the earphones to your device, please try the following:
– Ensure that the earphones are charged, switched on, paired with and connected to your device.
– Check the earphones are within 10 metres (30 feet) of your device and that there are no obstructions
(such as walls or other electronic devices) between the earphones and the device.
– The earphones can only pair to one device at a time, so please ensure there are no conicting
wireless devices trying to connect to the earphones
• If the earphones will not switch o, you can reset them back to normal by putting them on charge
• If you receive an intermittent signal, please ensure the earphones are fully charged before continuing use
• If you do not use the earphones for longer than 3 minutes whilst not connected to a device, they will
automatically power o to conserve power
We hope you’ve now got all the information you need to get started, but if you’re having problems with
anything, please feel free to contact us at: suppor[email protected].uk
Specications
Works with Bluetooth
®
V4.1
Wireless connectivity distance up to 10 m
Frequency response 20 – 20 kHz
Talk time up to 5 hours
Play time up to 5 hours
Charge time up to 1.5 hours
Standby time up to 3 months
Battery type LiPo
Battery capacity 80 mAh
10
Please do not attempt to open this product. There are no user serviceable parts inside, in particular if your product has an embedded,
non-replaceable battery, do not attempt to access or remove the battery as this may cause personal injury and will damage the product.
Making any attempt to open the product or carry out repair voids any and all warranties.
We apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur as a result of product
improvement and development.
‘Hereby, Kondor Ltd declares that the radio equipment type,
KSIMA Immerse Active Wireless Earphones, is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
internet address: http://kondor.co.uk/product-documents.’
/
