Electrolux EIW60002X User manual

Brand: Electrolux

Model: EIW60002X

Category: Sanitary ware

Type: User manual

Errata corrige

REFRESHMENT CENTER

Built-In appliance

errata corrige electrolux 3

Package content

The package contains the mentioned material with

the addition of:

- 10 screws 3.5x16 and 3 screws M4x8

- user instruction manual

Installation

Cabinet dimensions

1.The required dimensions of the cabinet space for

the positioning of the unit are:

1. Height (1): 380mm

2. Depth (2): 560mm

3. Width (3): 560mm

Unit position inside the cabinet

- After making sure that the overall size of the

unit fits the cabinet space, install the base

plate (Fig.3). If necessary, please use the

spacers to adapt and fix the base plate to the

cabinet space (Fig.4)

Fig. 4

− Mount the sliding rails onto the base plate

using the included 10 self-tapping screws

3.5x16 (Fig. 5)

Fig. 5

− Place the Refreshment Center on the

telescopic runners and push it slowly until the

confirming "click" sound.

Fig. 6

4 electrolux errata corrige

Filter cartridge first installation

Lift the drip tray and pull upward the locking

spring of the Refreshment center util it unblocks

(Fig.8)

Fig. 8

Pull the bottom edge of the unit and extract the

Refreshment Center (Fig.9).

After pulling out the unit it is easier to access the

left side, that contains the filter cartridge.

Fig. 9

Remove the capsule. Connect the filter cartridge

to the filter head turning it counter-clockwise

(Fig.10)

Fig. 10

Check for water leaks. Dry the area before

installing the unit in the opening.

Aligner installation

- After making sure that the overall size of the

unit fits the cabinet space, install the base

plate (Fig.3). If necessary, please use the

spacers to fix the base plate to the cabinet

space (Fig.4). Its function is to line up the

Refreshment Centre to the other possible built-

in appliances in the kitchen.

Fig. 4

errata corrige electrolux 5

bottle first installation

Disposable Bottle

The CO2 bottle can be found on the left side of the

unit. Remove the green cap and screw the

pressure reducer onto the bottle until fully

tightened (Fig.11).

Open the valve on the reducer until it reaches a

pressure of about 3 bar (Fig.12).

In order to obtain a higher level of CO2

concentration, it is possible to increase the

pressure up to a maximum of about 4 bar.

Fig. 11

Rechargeable bottle

The CO2 bottle can be found on the left side of

the unit. Together with the pressure reducer is a

fitting adaptor with seal ring included. The

adaptor is to be screwed onto the bottle head.

For a complete assembly, screw the pressure

reducer onto the adaptor.

Open the valve on the reducer until it reaches a

pressure of about 3 bar (Fig.12).

In order to obtain a higher level of CO2

concentration, it is possible to increase the

pressure up to a maximum of about 4 bar.

Fig. 12

Using the Refreshment Center

Warning

Use the general switch on the right side of

the unit to switch it on. The on/off switch

of the front panel does not have a stand-

by function; the unit is still on, but all

functions are disabled. To switch on and off

the unit always use the internal general

switch, even when resetting.

6 electrolux errata corrige

Alarms

Led indications Meaning

Filter red led

blinks slowly

Filter is about to exhaust. 2,700 liters of

water have been dispensed.

Please replace the filter cartridge as

described in the paragraph "Filter

replacement"

Filter red led is

Filter exhausted. 2,800 liters of water have

been dispensed.

Please replace the filter cartridge as

described in the paragraph "Filter

replacement"

Filter red led

stays lit

All dispense buttons disabled.

The limit has been reached of 2,840 liters.

To reset all dispense functions, please

replace the filter cartridge as described in

the paragraph "Filter reaplacement"

Carbonated

water led blinks

slowly

Carbonated water is disabled.

A protection device on the pump activated.

To reset the unit, please turn it off and after

few seconds switch it back on using the

on/off button on the control panel.

CO2 bottle led

stays lit

Carbonated water is disabled.

CO2 bottle is empty.

To restore carbonated water dispensing,

please replace the bottle as described in the

paragraph "CO2 bottle replacement".

- Ambient water

- ice cubes

leds blink

simultaneously

Ice forming bin blocked.

To reset the unit switch it off and then back on pushing the

on/off button on the front panel.

errata corrige electrolux 7

Led indications Meaning

- Ambient water

- cold water

- carbonated

water

leds blink

simultaneously

and fast

Volumetric turbine malfunctioning. The two possible causes

are:

1. Lack of water supply from the water main;

2. Low pressure in the water inlet.

Please check the presence of water supply to the unit.

Turn unit off and then back on using the on/off switch on

the front panel.

- carbonated

water

- ambient water

- cold water

- ice cubes

leds blink

simultaneously

This alarm comes on only when the unit is turned on

through the main on/off switch. It means that the main

tank is empty due to a lack of water supply from the main.

To reset the unit, turn off the main switch on the side of

the Refreshment Center. Check and make sure there is

water supply to the unit, then turn the unit back on.

All leds blink

simultaneously

All dispense buttons disabled. The two possible causes are:

1. Presence of water on the base of

the unit;

2. The water level inside the tank is

too high.

In the first case, switch off the unit and dry the base.

In the second case, reset the unit by turning it off and then

back on through the main switch on the side of the

Refreshment Center.

Maintenance and cleaning

Please do not touch the front control panel with wet or oily hands, in order to

avoid the malfunctioning of the touch control.

8 electrolux errata corrige

Ice melting

Do not block ice exit with any object,

since it may damage the unit or prevent

the correct closing of the exit. This would

cause a rise in the internal temperature

with subsequent rapid ice melting

bottle replacement (for food)

When CO2 led turns on, please replace the old bottle with a new one as

described below:

1. unblock the locking spring from under the

drip tray (Fig. 8). Pull out with both hands

the bottom of the unit, letting the

Refreshment center slide on the

telescopic runners (Fig.15). After pulling

out the unit it is easier to access the left

side, where the CO2 bottle is installed;

2. grab the bottle and extract it;

Fig. 15

3. hold the pressure reducer and turn the

bottle clockwise (fig.16) to separate the

bottle from the pressure reducer;

4. screw the new bottle to the reducer

counter-clockwise till fully tightened (Fig.

11);

5. lock the new bottle on the side of the

unit.

Fig. 16

errata corrige electrolux 9

Sanification + filter cartridge replacement

When the “filter” led turns on, it is necessary to replace the cartridge filter as

described below:

1. unblock the locking spring (Fig.8) and pull

out the Refreshment Center unit (Fig.15);

2. turn off the unit through the main on/off

switch;

3. see filter cartridge on the left (Fig. 1a);

4. rotate the exhausted cartridge clockwise

about a quarter of a turn to remove it

from the head (fig.17) and extract it

avoiding water spillage;

5. fill the sanification cartridge with

“Neutral Detergent”. Insert the sanitizing

cartridge on the filter head by rotating it

counter-clockwise about a quarter turn

(Fig.18);

6. in case of water spillage, dry the base and

make sure there are no leaks;

7. place a big cup under the water dispense

nozzle (the appliance will deliver round

250ml of water);

8. turn on the main switch pushing at the

same time the light-switching button for

approximately 5". Press the "light" button

two more times, each time for 5". This

will activate the sanitizing mode,

displayed as a red led moving through all

the buttons of the front panel; during this

operation, the inner tank will be

sanitized. After this initial cleaning cycle,

the unit will automatically dispense some

cold and ambient water mixed with the

sanitizing solution;

Fig. 17

Fig. 18

Fig. 19

if few days after the

installation the filter

replacement led turns on,

please activate the sanitation

procedure to restore all

functions. In such case, filter

replacement is not necessary

10 electrolux errata corrige

9. turn off the unit through the main switch;

10. remove the sanification cartridge (Fig.19)

and connect the new filter cartridge to

the head as shown on filter cartridge

instructions (Fig.20);

11. turn on the main switch and push the

Refreshment Center into the cabinet until

the locking spring clicks (Fig.21);

12. wait 4 minutes before activating the unit

pushing the on/off button on the control

panel;

13. dispense 1 liter of cold, carbonated and

ambient water to fully rinse the lines and

eliminate any residual of sanitizing

solution.

Fig. 20

Fig. 21

Warning

During the sanitizing

procedure please do not

dispense carbonated water.

errata corrige electrolux 11

12 electrolux errata corrige

Subject to change without notice

Electrolux EIW60002X User manual

Brand: Electrolux

Model: EIW60002X

Category: Sanitary ware

Type: User manual

Download PDF

report

Electrolux EIW60002X User manual

Electrolux EIW60002X User manual

Related papers

Other documents