Aeg-Electrolux PWE9038-M User manual

REFRESHMENT CENTER

Built-in appliance

INSTRUCTION MANUAL

PERFEKT IN FORM UND FUNKTION

2

3

Dear Customer

Thank you for choosing one of our high-quality products.

With this appliance you will experience the perfect combination of functional design and cutting

edge technology.

Convince yourself that our appliances are engineered to deliver the best performance and control -

indeed we are setting the highest standards of excellence.

In addition to this you find environmental and energy saving aspects as an integral part of our

products.

To ensure optimal and regular performance of your appliance please read this instruction manual

carefully. It will enable you to navigate all processes perfectly and most efficiently.

To refer to this manual any time you need to, we recommend you to keep it in a safe place. And

please pass it to any future owner of the appliance.

We wish you much joy with your new appliance.

The following symbols are utilized with this manual

Safety information

Environment

Disposal directives

4

INDEX

Electrical safety..........................................................................................5

Electrical safety................................................................................................................................................5

Installation.......................................................................................................................................................6

Use ................................................................................................................................................................6

Cleaning............................................................................................................................................................6

Environment.....................................................................................................................................................6

Appliance description ................................................................................7

Units 7

Identification plate (Fig.2)...............................................................................................................................9

Technical Characteristics .................................................................................................................................9

Installation...............................................................................................10

Package content.............................................................................................................................................10

1. Unit positioning ....................................................................................................................................11

2. Water mains and siphon connection.....................................................................................................13

3. Install filter cartridge...........................................................................................................................14

4. Startup..................................................................................................................................................16

Using the Refreshment Unit ...........................................................................................................................17

Front touch panel.....................................................................................................................................17

Dispensing................................................................................................................................................18

Allarms .....................................................................................................19

Maintenance .............................................................................................21

CO2 bottle replacemen..............................................................................................................................21

Sanification + filtration cartridge...........................................................................................................22

Environment care.....................................................................................24

Electric diagram.......................................................................................25

Hydraulic diagram ...................................................................................26

Errata corrige ......……………………………………………27

Guarantee/Customer Service ...................................................................36

5

Electrical safety

This appliance conforms to the following safety electrical European Directives:

This manual has been written for your own safety and of others. Please read manual carefully before

installation and/or use. Please keep this instruction manual in a safe and dry place. This appliance

conforms to the following safety electrical European Directives: 73/23/CEE, 89/336/CEE, 92/31/CEE,

98/37/CEE.

Please keep this instruction manual in a safe and dry place.

This manual has been written for you own safety and of others. Please read manual carefully before

installation and/or use.

Electrical safety

The unit needs to be connected to a power supply line that conforms fully to local safety regulations

regarding electrical safety. If in doubt please have your electrical system checked by a specialized

electrician.

Please do not try to repair the unit as you might cause additional damage. Contact your nearest

Technical assistance center.

Remove power supply cord before proceeding with repair operations.

If the power supply cord appears to be damaged, please ask for a replacement cord.

6

Installation

Please handle appliance with care to prevent damaging of the refrigeration circuit.

Avoid prolonged exposure of the appliance to direct sunlight.

To guarantee maximum stability and safety, it’s necessary to install the built-in appliance only in

AEG, REX and Electrolux sized cabinets.

Please follow instruction carefully before, during and after installation.

If the appliance is transported in vertical position, please place in horizontal (normal) position and

wait 1 hour for the oil to return to the compressor before turning unit on.

Do not bend water supply and discharge tube excessively during installation.

Use

Do not use the Refreshment Unit for something else other than dispense cold, carbonated, ambient

water and ice. An incorrect use of the appliance may harm people or cause cause damage to the

appliance itself.

Do not allow children to use the appliance if not under the supervision of adults.

Cleaning

Do not use metallic tools to clean the appliance as it may cause damage.

Environment

Please follow local disposal regulations.

7

Appliance description

The Refreshment Unit is a domestic appliance designed to dispense purified cold, carbonated and

ambient temperature water and ice-cubes.

The appliance has 2 outlet from which the following products can be dispensed:

- Ambient temperature water

- Cold water

- Carbonated water

- Ice-Cubes.

Units

The unit is mainly composed of:

1. St. Steel front display

2. Water dispense nozzle

3. Glass touch command panel

4. Ice dispense outlet

5. Drip tray

Fig. 1a

9 11 8 12

1

2

3

4

5

8

6. Main on/off switch

7. Power supply socket

8. Filter cartridge

9. CO2 bottle

10. H2O inlet

11. H2O pressure regulator with gauge

12. Filter head

13. H2O drainage

Fig. 1b

6 7 10 13

9

Identification plate (Fig. 2)

Should you need to contact a

technical Assistance Center,

make sure you have the serial

number handy for identification.

The serial number is on the

identification plate in the side of

the appliance. Extract from cabinet

to identify plate.

MODEL PNC

942 490 XXXPWE9038-M

XXXXXXXX

TYPE SERIAL No.:

Refreshment Center

MADE IN ITALY

230 V ~ 50 Hz

MAX 190 W

Fig. 2

Technical Characteristics

Power Supply 230-240 V

Frequency 50 Hz

Power consumption 190 W

Cold water dispense capacity 2lt @ 1 l/min.

Carbonated water dispense capacity 2lt @ 1 l/min

Dispense temperature < 13°C

Water mains pressure (water inlet) > 2.0 bar

CO

2

pressure 2.5 -4 bar

Filtration 0.5 micron

Filter capacity 2840 litri

Ambient temperature conditions range 18°C-32°C

Unit dimensions L x P x H (mm) 594x554xH378

Weight 38 Kg

Refrigerant gas R134a – 60gr

10

Installation

Warning

In order for the unit to work correctly, the Technical Characteristics specification chart on page. 6

needs to be observed.

Installation steps:

1. Refreshment unit assembly inside kitchen

2. Water mains connection

3. Water filter connection

4. Electric power supply

Package content

Open package and immediately check for any transport damages. During installation please handle

with care.

Inside you should find the following material:

A. Refreshment Center

B. 2 Sliding Rails

C. Mounting base plate

D. 6 spacers 2x1mm, 2x2mm,

2x3mm

Power supply cord

A

B

C

D

11

H2O inlet flexible hose and

discharge tube

Filtration Cartridge

Sanitazing cartridge and liquid

2. Unit positioning

Please install unit as far away as possible from heat sources

Please install unit higher than the water drainage in the kitchen

Please don’t install the Refreshment Center farther than 4m from the water main or please use

another water inlet and discharge tubes

The dimension requirements for the kitchen cabinet are:

1. Height (1): 360mm

2. Depth (2): 580mm

3. Width (3): 564mm

5

4

0

5

0

1

2

3

Fig. 3

12

- Install the mounting base plate inside the kitchen cabinet after checking after checking

dimension requirements as shown in Fig. 3. If necessary, please use the spacers to fix the

mounting base plate to the cabinet.

- Mount the 2 sliding rails onto the base plate.

- Place the Refreshment Unit on the sliding rails.

Fig. 4

13

3. Water mains and siphon connection

Warning

Connect only to potable water mains.

All water mains connections should be carried out by a certified plummer.

Warning

Water mains pressure can be set through the H2O pressure regulator placed near the CO2 bottle.

Pressure should be no higher than 3.0 bars and no lower than 2.0 bars.

Complete following operations (Fig. 5):

- Connect the flexible hose to the H2O inlet on the unit. Connect water mains to flexible hose.

- Connect discharge tube to discharge barbed connection on unit and to sink siphon.

Warning

Please do not install Refreshment Center farther than 4 meters or please get longer inlet and

discharge tubes.

Fig. 5

Water inlet ¾”

Water discharge ¾”

14

4. Install filter cartridge

Lift locking spring placed under driptray (Fig. 5a).

Fig. 5a

Pull unit from cabinet.

On the left side of the unit please find the

filter cartridge (Fig. 6).

Fig. 6

Remove filter plastic cap and install filter in

filter head as shown on filter instruction

booklet (Fig. 7).

Fig. 7

Open the on/off valve placed near the filter

cartridge.

Fig. 8

Filter cartridge

15

Check for water leaks and make sure the CO2

bottle is tightly fixed on the CO2 pressure

regulator.

Open the pressure regulator valve and set

pressure to 3 bars on gauge.

Pressure can be increased to

4 bars to increase carbonation levels (Fig. 9).

Fig. 9

16

5. Startup

Warning

Before plugging unit to power supply, please check for correct power supply voltage and frequency

as stated on Technical Characteristic chart (see page 9).

Fig. 10

Connect unit to 230V through supplied cord.

Electric supply circuit should conform to local laws and regulations.

Warning

The supplier declines any responsibility should any safety rule not be respected during installation.

Turn unit on through main on/off

switch on side of unit. The unit will

undergo an initialization process

which will take approx. 4 minutes.

17

This preliminary operation will be carried out every time the unit is turned off and on through the

main on/off switch inside the cabinet. During this process the touch control panel is inactive.

After 4 minutes turn unit on through on/off button on touch control panel to activate all functions

At this point please wait approx. 3 hours before the unit reaches final working temperatures in

order to dispense cold water, carbonated water and ice-cubes. Ambient water is ready immediately.

Using the Refreshment Center

Front touch panel

1. Empty CO2 bottle led

2. On/Off switch

3. Water ambient temperature button

4. Carbonated water button

5. Cold water button

6. Ice dispense button

7. Light button On/Off

8. Exhaust filter led

1

2

3

4

5

6

7

8

18

Dispensing

After turning appliance on through on/off

switch on touch screen, wait for cooling time

before dispensing.

Place a glass under dispense nozzle. Press

button corresponding to desired selection.

Release until desired dispense water level or

number of ice-cubes is reached. Please do not

dispense more than

1 liter of carbonated water continuously since

you might experience CO2 exhaust from

nozzle. Should that occur, please wait 1

minute and restart dispensing carbonated

water.

Dispensing is signalled by the corresponding

led.

In order to dispense in bottles or carafes,

please extract dispense nozzle by grabbing on

sides of nozzle and pulling forward.

19

Allarms

Led indications Message

Led blinks slowly

Filter is about to exhaust. 2900 liters have been dispensed.

Please change filter as described in the following chapters.

Led is lit

Filter is about to exhaust. 2980 liters have been dispensed.

Please change filter as described in the following chapters.

Led is lit

All dispense buttons disabled.

3000 liters have been reached.

Please change filter as described in the following chapters.

Carbonated water

led blinks slowly

Carbonated water is disabled.

Time-out protection on carbonation pump activated.

To reset status please turn unit off/on on touch control panel.

CO2 bottle led on

Carbonated water is disabled.

CO2.bottle is empty.

Replace CO2 bottle to restore Carbonated water dispensing.

Please change CO2 bottle as described in the following

chapters.

20

Leds

ambient water

ice

blink simultaneously

Ice forming bin blocked.

Turn unit on/off through main on/off switch on side of unit.

Leds

ambient water

cold water

carbonated water

blink simultaneously

Volumetric turbine malfunctioning. Dispense functions enabled but

during dispense operation the 3 leds will blink.

Leds

carbonated water

ambient water

cold water

ice

blink simultaneously

Main water tank fill time-out. Please check water supply to unit. Make

sure filter shut off valve to be open.

To reset status turn unit on/off through main switch inside cabinet.

All leds on

simultaneously

All dispense buttons disabled. 2 main causes:

Water present on base of unit. Possible leak.

Water level too high inside water tank. Water discharge blocked.

For the first case switch off and dry the base of the unit.

For the second case turn unit on/off through main switch inside

cabinet.

Page is loading ...

Aeg-Electrolux PWE9038-M User manual

Aeg-Electrolux PWE9038-M User manual

Related papers

Other documents