Aeg-Electrolux PWE9038-M User manual

Category
Sanitary ware
Type
User manual
REFRESHMENT CENTER
Built-in appliance
INSTRUCTION MANUAL
PERFEKT IN FORM UND FUNKTION
2
3
Dear Customer
Thank you for choosing one of our high-quality products.
With this appliance you will experience the perfect combination of functional design and cutting
edge technology.
Convince yourself that our appliances are engineered to deliver the best performance and control -
indeed we are setting the highest standards of excellence.
In addition to this you find environmental and energy saving aspects as an integral part of our
products.
To ensure optimal and regular performance of your appliance please read this instruction manual
carefully. It will enable you to navigate all processes perfectly and most efficiently.
To refer to this manual any time you need to, we recommend you to keep it in a safe place. And
please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
The following symbols are utilized with this manual
Safety information
Environment
Disposal directives
4
INDEX
Electrical safety..........................................................................................5
Electrical safety................................................................................................................................................5
Installation.......................................................................................................................................................6
Use ................................................................................................................................................................6
Cleaning............................................................................................................................................................6
Environment.....................................................................................................................................................6
Appliance description ................................................................................7
Units 7
Identification plate (Fig.2)...............................................................................................................................9
Technical Characteristics .................................................................................................................................9
Installation...............................................................................................10
Package content.............................................................................................................................................10
1. Unit positioning ....................................................................................................................................11
2. Water mains and siphon connection.....................................................................................................13
3. Install filter cartridge...........................................................................................................................14
4. Startup..................................................................................................................................................16
Using the Refreshment Unit ...........................................................................................................................17
Front touch panel.....................................................................................................................................17
Dispensing................................................................................................................................................18
Allarms .....................................................................................................19
Maintenance .............................................................................................21
CO2 bottle replacemen..............................................................................................................................21
Sanification + filtration cartridge...........................................................................................................22
Environment care.....................................................................................24
Electric diagram.......................................................................................25
Hydraulic diagram ...................................................................................26
Errata corrige ......……………………………………………27
Guarantee/Customer Service ...................................................................36
5
Electrical safety
This appliance conforms to the following safety electrical European Directives:
This manual has been written for your own safety and of others. Please read manual carefully before
installation and/or use. Please keep this instruction manual in a safe and dry place. This appliance
conforms to the following safety electrical European Directives: 73/23/CEE, 89/336/CEE, 92/31/CEE,
98/37/CEE.
Please keep this instruction manual in a safe and dry place.
This manual has been written for you own safety and of others. Please read manual carefully before
installation and/or use.
Electrical safety
The unit needs to be connected to a power supply line that conforms fully to local safety regulations
regarding electrical safety. If in doubt please have your electrical system checked by a specialized
electrician.
Please do not try to repair the unit as you might cause additional damage. Contact your nearest
Technical assistance center.
Remove power supply cord before proceeding with repair operations.
If the power supply cord appears to be damaged, please ask for a replacement cord.
6
Installation
Please handle appliance with care to prevent damaging of the refrigeration circuit.
Avoid prolonged exposure of the appliance to direct sunlight.
To guarantee maximum stability and safety, it’s necessary to install the built-in appliance only in
AEG, REX and Electrolux sized cabinets.
Please follow instruction carefully before, during and after installation.
If the appliance is transported in vertical position, please place in horizontal (normal) position and
wait 1 hour for the oil to return to the compressor before turning unit on.
Do not bend water supply and discharge tube excessively during installation.
Use
Do not use the Refreshment Unit for something else other than dispense cold, carbonated, ambient
water and ice. An incorrect use of the appliance may harm people or cause cause damage to the
appliance itself.
Do not allow children to use the appliance if not under the supervision of adults.
Cleaning
Do not use metallic tools to clean the appliance as it may cause damage.
Environment
Please follow local disposal regulations.
7
Appliance description
The Refreshment Unit is a domestic appliance designed to dispense purified cold, carbonated and
ambient temperature water and ice-cubes.
The appliance has 2 outlet from which the following products can be dispensed:
- Ambient temperature water
- Cold water
- Carbonated water
- Ice-Cubes.
Units
The unit is mainly composed of:
1. St. Steel front display
2. Water dispense nozzle
3. Glass touch command panel
4. Ice dispense outlet
5. Drip tray
Fig. 1a
9 11 8 12
1
2
3
4
5
8
6. Main on/off switch
7. Power supply socket
8. Filter cartridge
9. CO2 bottle
10. H2O inlet
11. H2O pressure regulator with gauge
12. Filter head
13. H2O drainage
Fig. 1b
6 7 10 13
9
Identification plate (Fig. 2)
Should you need to contact a
technical Assistance Center,
make sure you have the serial
number handy for identification.
The serial number is on the
identification plate in the side of
the appliance. Extract from cabinet
to identify plate.
MODEL PNC
942 490 XXXPWE9038-M
XXXXXXXX
TYPE SERIAL No.:
Refreshment Center
MADE IN ITALY
230 V ~ 50 Hz
MAX 190 W
Fig. 2
Technical Characteristics
Power Supply 230-240 V
Frequency 50 Hz
Power consumption 190 W
Cold water dispense capacity 2lt @ 1 l/min.
Carbonated water dispense capacity 2lt @ 1 l/min
Dispense temperature < 13°C
Water mains pressure (water inlet) > 2.0 bar
CO
2
pressure 2.5 -4 bar
Filtration 0.5 micron
Filter capacity 2840 litri
Ambient temperature conditions range 18°C-32°C
Unit dimensions L x P x H (mm) 594x554xH378
Weight 38 Kg
Refrigerant gas R134a – 60gr
10
Installation
Warning
In order for the unit to work correctly, the Technical Characteristics specification chart on page. 6
needs to be observed.
Installation steps:
1. Refreshment unit assembly inside kitchen
2. Water mains connection
3. Water filter connection
4. Electric power supply
Package content
Open package and immediately check for any transport damages. During installation please handle
with care.
Inside you should find the following material:
A. Refreshment Center
B. 2 Sliding Rails
C. Mounting base plate
D. 6 spacers 2x1mm, 2x2mm,
2x3mm
Power supply cord
A
B
C
D
11
H2O inlet flexible hose and
discharge tube
Filtration Cartridge
Sanitazing cartridge and liquid
2. Unit positioning
Please install unit as far away as possible from heat sources
Please install unit higher than the water drainage in the kitchen
Please don’t install the Refreshment Center farther than 4m from the water main or please use
another water inlet and discharge tubes
The dimension requirements for the kitchen cabinet are:
1. Height (1): 360mm
2. Depth (2): 580mm
3. Width (3): 564mm
5
4
0
5
0
1
2
3
Fig. 3
12
- Install the mounting base plate inside the kitchen cabinet after checking after checking
dimension requirements as shown in Fig. 3. If necessary, please use the spacers to fix the
mounting base plate to the cabinet.
- Mount the 2 sliding rails onto the base plate.
- Place the Refreshment Unit on the sliding rails.
Fig. 4
13
3. Water mains and siphon connection
Warning
Connect only to potable water mains.
All water mains connections should be carried out by a certified plummer.
Warning
Water mains pressure can be set through the H2O pressure regulator placed near the CO2 bottle.
Pressure should be no higher than 3.0 bars and no lower than 2.0 bars.
Complete following operations (Fig. 5):
- Connect the flexible hose to the H2O inlet on the unit. Connect water mains to flexible hose.
- Connect discharge tube to discharge barbed connection on unit and to sink siphon.
Warning
Please do not install Refreshment Center farther than 4 meters or please get longer inlet and
discharge tubes.
Fig. 5
Water inlet ¾”
Water discharge ¾”
14
4. Install filter cartridge
Lift locking spring placed under driptray (Fig. 5a).
Fig. 5a
Pull unit from cabinet.
On the left side of the unit please find the
filter cartridge (Fig. 6).
Fig. 6
Remove filter plastic cap and install filter in
filter head as shown on filter instruction
booklet (Fig. 7).
Fig. 7
Open the on/off valve placed near the filter
cartridge.
Fig. 8
Filter cartridge
15
Check for water leaks and make sure the CO2
bottle is tightly fixed on the CO2 pressure
regulator.
Open the pressure regulator valve and set
pressure to 3 bars on gauge.
Pressure can be increased to
4 bars to increase carbonation levels (Fig. 9).
Fig. 9
16
5. Startup
Warning
Before plugging unit to power supply, please check for correct power supply voltage and frequency
as stated on Technical Characteristic chart (see page 9).
Fig. 10
Connect unit to 230V through supplied cord.
Electric supply circuit should conform to local laws and regulations.
Warning
The supplier declines any responsibility should any safety rule not be respected during installation.
Turn unit on through main on/off
switch on side of unit. The unit will
undergo an initialization process
which will take approx. 4 minutes.
17
This preliminary operation will be carried out every time the unit is turned off and on through the
main on/off switch inside the cabinet. During this process the touch control panel is inactive.
After 4 minutes turn unit on through on/off button on touch control panel to activate all functions
At this point please wait approx. 3 hours before the unit reaches final working temperatures in
order to dispense cold water, carbonated water and ice-cubes. Ambient water is ready immediately.
Using the Refreshment Center
Front touch panel
1. Empty CO2 bottle led
2. On/Off switch
3. Water ambient temperature button
4. Carbonated water button
5. Cold water button
6. Ice dispense button
7. Light button On/Off
8. Exhaust filter led
1
2
3
4
5
6
7
8
18
Dispensing
After turning appliance on through on/off
switch on touch screen, wait for cooling time
before dispensing.
Place a glass under dispense nozzle. Press
button corresponding to desired selection.
Release until desired dispense water level or
number of ice-cubes is reached. Please do not
dispense more than
1 liter of carbonated water continuously since
you might experience CO2 exhaust from
nozzle. Should that occur, please wait 1
minute and restart dispensing carbonated
water.
Dispensing is signalled by the corresponding
led.
In order to dispense in bottles or carafes,
please extract dispense nozzle by grabbing on
sides of nozzle and pulling forward.
19
Allarms
Led indications Message
Led blinks slowly
Filter is about to exhaust. 2900 liters have been dispensed.
Please change filter as described in the following chapters.
Led is lit
Filter is about to exhaust. 2980 liters have been dispensed.
Please change filter as described in the following chapters.
Led is lit
All dispense buttons disabled.
3000 liters have been reached.
Please change filter as described in the following chapters.
Carbonated water
led blinks slowly
Carbonated water is disabled.
Time-out protection on carbonation pump activated.
To reset status please turn unit off/on on touch control panel.
CO2 bottle led on
Carbonated water is disabled.
CO2.bottle is empty.
Replace CO2 bottle to restore Carbonated water dispensing.
Please change CO2 bottle as described in the following
chapters.
20
Leds
ambient water
ice
blink simultaneously
Ice forming bin blocked.
Turn unit on/off through main on/off switch on side of unit.
Leds
ambient water
cold water
carbonated water
blink simultaneously
Volumetric turbine malfunctioning. Dispense functions enabled but
during dispense operation the 3 leds will blink.
Leds
carbonated water
ambient water
cold water
ice
blink simultaneously
Main water tank fill time-out. Please check water supply to unit. Make
sure filter shut off valve to be open.
To reset status turn unit on/off through main switch inside cabinet.
All leds on
simultaneously
All dispense buttons disabled. 2 main causes:
Water present on base of unit. Possible leak.
Water level too high inside water tank. Water discharge blocked.
For the first case switch off and dry the base of the unit.
For the second case turn unit on/off through main switch inside
cabinet.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Aeg-Electrolux PWE9038-M User manual

Category
Sanitary ware
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI