Electrolux EIW63810X User manual

Brand: Electrolux

Model: EIW63810X

Type: User manual

User Manual

Refreshment Centre

EIW63810X

2 electrolux

Contents

Safety information 2

Appliance description 4

Main components 4

Rating plate 4

Technical specifications 5

Package content 5

Installation 6

Unit positioning 6

Unit connection 9

Usage 11

Maintenance and cleaning 13

Signals for users 17

What to do if... 18

Environment concerns 19

Safety information

Fundamental safety warnings

Warning The appliance must be

earthed in compliance with legislation.

Electrical and Water connection must

be carried out by qualified technicians

following the instructions

Warning Keep all packaging (plastic

bags, polystyrene foam) away from

children

Warning The appliance is not to be

used by people (including children)

with reduced physical, sensory or

mental capabilities, or lack of

experience and knowledge, unless

they have been given supervision or

instruction concerning use of the

appliance by a person responsible for

their safety

Warning In order for children not to

play with the appliance, a close

supervision is required

Warning Do not grasp the appliance

when it is out of the cabinet. Do not

rest recipients containing liquids or

inflammable or corrosive materials on

top of the appliance

Warning Do not use the appliance

when extracted, except for installation,

maintenance and “What to to do if...”

sections. For any other operation

make sure the appliance is inactive

Warning Water leakage will occur

when the discharge tap is open

Instructions

Read these instructions carefully before

using the appliance.

• Keep the instructions

• Failure to respect these instructions

may result in injuries or in damages to

the appliance

The manufacturer is not liable for damage

deriving from failure to respect these

instructions

Use original or manufacturer

recommended accessories and spare

parts only.

Designated use

Warning This is a household

appliance only

It is not intended to be used in:

• Staff kitchen areas in shops

• Offices and other working environments

electrolux 3

• Farm houses

• By clients in hotels, motels, and other

residential type of environments

• Bed and breakfast type of environments

The appliance is designed and made to

supply water and ice. Other uses are

considered improper. This appliance is not

suitable for commercial use. The

manufacturer is not liable for damage

deriving from improper use of the

appliance.

Electrical safety

Warning The appliance must be

earthed in compliance with legislation.

Electrical connection must be carried

out by qualified technicians following

the instructions

Warning This is an electrical

appliance, it is therefore important to

respect the following safety warnings:

• Never touch the plug with wet hands.

• Make sure the socket is freely

accessible at all times, enabling the

appliance to be unplugged when

necessary.

• If the appliance is faulty, do not attempt

to repair it. Turn it off using the power

switch, unplug from the main socket and

contact your local Service Force Centre.

Check that the main power supply voltage

corresponds to the value indicated on the

rating plate on the left side of the

appliance. Connect the appliance to an

efficiently earthed and correctly installed

socket. If the power socket does not

match the plug on the appliance, have the

socket replaced with a suitable type by a

qualified professional. Do not use multiple

sockets or extensions.

During installation and Use

Warning Move the appliance carefully

in order not to damage components of

the refrigeration circuit and to avoid

gas leaks

Warning Avoid prolonged exposure of

the appliance to direct sunlight

Warning When installing the

appliance do not over bend hoses

After removing the packaging, make sure

the product is complete and undamaged

and that all components are present.

Do not use the appliance if it is visibly

damaged. Contact your local Service

Force Centre.

• Installation must be carried out by

qualified professional in compliance with

legislation in force in the country of

installation.

• The packing elements (plastic bags,

polystyrene foam, etc.) should be kept

out of reach of children.

• Do not install the appliance in rooms

where the temperature may raise up to

35°C or above.

Surface treatment

Warning Before performing any

washing operation, the appliance

must be switched off and unplugged

from the power supply

Warning Do not use solvents or

abrasive detergents.

A soft damp cloth will suffice

Environmental protection

Electrical appliances must not be disposed

of as household waste. Appliances with

this symbol are covered by European

Directive 2002/96/EC. All unused electric

and electronic appliances must be

disposed of separately from household

waste and taken to country-authorised

special centres.

4 electrolux

Appliance description

Refreshment Centre is a household

appliance that refrigerates, purifies and

carbonates the water from the mains and

makes ice shards.

Its two nozzles dispense:

• Ambient water

• Cold sparkling water

• Cold still water

• Ice shards

Main components

Refreshment Centre's main components

1 Stainless steel front frame

2 Water discharge nozzle

3 Water dispense nozzle

4 Control panel (icons and LEDs)

5 Ice dispensing nozzle

6 Drip tray

7 CO₂ pressure reducer

8 Filter head

9 CO₂ bottle

10 Water pressure reducer

11 Water discharge tap

12 Water inlet

13 Filter cartridge

14 Rating plate

15 Power switch

16 Power supply socket

Rating plate

Under no circumstances should you

attempt to repair the machine yourself.

Repair carried out by inexperienced

people could cause injury or serious

malfunctioning. Contact your local Service

Force Centre. Always insist on genuine

spare parts.

When contacting your local Service Force

Centre, you will be asked to give the data

and the feature information of the

Refreshment Centre, to be found in the

rating plate on the left side of the

appliance.

1 Rating plate

electrolux 5

Technical specifications

Power Supply Voltage 230-240 V

Frequency 50 Hz

Power consumption MAX 260 W

Cold still water dispense capacity 2lt @ 1 l/min.

Cold sparkling water dispense capacity 2lt @ 1 l/min.

Ice shards 200g / 2h

Dispense temperature < 13°C

Water mains pressure (water inlet) > 0.2 MPa (> 2 bar), < 0.6 MPa (< 6 bar)

CO₂ pressure > 0.25 MPa (> 2.5 bar), < 0.40 MPa (< 4 bar)

Filtration 0.5 micron

Filter capacity 2840 litres

Climatic class SN (> +10°C, < +32°C)

Dimensions W x D x H 594x578x378 mm

Weight 34 Kg

Refrigerant gas R134a – 62gr

Package content

After removing the packaging, make sure

the product is complete and undamaged

and that all components are present.

Move it carefully avoiding shocks or

downfalls that may damage the

refrigeration circuit.

The package contains the following

material:

• Refreshment Centre

• 2 sliding rails

• Spacers 2x1mm, 2x2mm, 2x3mm

• 2 support brackets

• Frontal spacer

• Water inlet hose

• Filter cartridge

• Plastic hose for water tank discharge

• Rechargeable CO₂ bottle with adapting

junction or disposable CO₂ bottle

• CO₂ pressure reducer

• Cleaning cartridge

• Neutral detergent

• Safety strip to fix CO₂ bottle

• 8 4.5x16mm self threading screws for

support brackets

• 4 M6x12 circular spacers

• 3 M4x12 screws for frontal spacer

• 2 M4x12 screws to fix the Refreshment

Centre to sliding rails

6 electrolux

Installation

Warning It is necessary to install the

appliance properly. The power supply

and water connection data in the

Technical Specifications chart must

be observed

Unit positioning

• Check for minimum requirements

• Spacers installation

• Support brackets installation

• Sliding rails installation

• Positioning in the kitchen cabinet

• Frontal spacer installation

Unit connection

• Secure water discharge tap

• Pressure reducer first installation

• CO₂ bottle first installation

• Water mains connection

• Filter cartridge first installation

• Electrical connection

Unit positioning

Warning The installation of the

product should be made above the

level of the water mains

Warning To ensure proper ventilation,

leave a gap at the bottom of the

cabinet (see measurements in the

drawing)

Warning The installation of the

Refreshment Centre in direct

conjunction with an oven might cause

performance reduction

Warning Safety cut-out devices must

be fixed properly so that they cannot

be removed without tools

Check for minimum requirements

Verify the minimum measurements

required for a correct installation of the

appliance.

The Refreshment Centre must be installed

in a cabinet and the cabinet must be firmly

fixed to the wall.

225 cm

q min

380 + 2 mm

electrolux 7

Leave room behind the appliance as

described in these instructions to avoid

overheating.

520 m

m m

40 m

m m

Spacers installation

To ensure a smooth installation of the

appliance, you need the same internal

width as shown in the picture below. Use

the provided spacers to adjust internal

width.

For their correct positioning, place the

spacers directly in contact with both the

shelf and the side of the cabinet.

Support brackets installation

After positioning the spacers, place the

two provided support brackets.

For a correct installation, take the single

support bracket and place it directly in

contact with both the shelf of the cabinet

and the spacer if previously used.

Otherwise the bracket will be in direct

contact with both shelf and side of the

cabinet.

After this first phase, align the support

brackets to be flush with the front of the

cabinet.

Use the upper holes to correctly mount the

appliance at the right height.

Warning Mount the screws

perpendicularly to the cabinet in order

to guarantee the correct extraction of

the sliding rails

A pilot hole is recommended for an

easier assembly.

Extract the screws to continue the

mounting.

8 electrolux

Sliding rails installation

Position each rail on the side of the

cabinet. Please note that there is a

specific sliding rail for each side of the

cabinet.

Each sliding rail should be flush with the

support brackets, with spacers when

present and with the front of the cabinet.

1 Spacer

2 Sliding rail

3 Support bracket

Pull out the sliding rail until the cabinet

underneath becomes visible.

Fix the sliding rail, the support bracket and

the spacer with the provided self-threading

screws 4.5x16.

When extracting the sliding rails, only

one of the frontal holes will become

visible. After mounting the

corresponding screw, move the rail

again to see the second hole and

mount the corresponding screw.

Positioning in the kitchen cabinet

Pull the sliding rails completely out, and

place the Refreshment Centre on them

making sure that the conical pivots match

the holes on the base.

Fix the Refreshment Centre on the bottom

side of the sliding rails with the 2 provided

M4x12 screws.

Push back the Refreshment Centre, until it

is locked into position.

Check aesthetic alignment with the

cabinet and use the provided circular

spacers M6x12 for final adjustment.

electrolux 9

Frontal spacer installation

When included in the package, and if

necessary, fix the frontal spacer with the 3

supplied M4x12 screws.

1 Frontal spacer

2 M4x12 screws

Unit connection

All the operations below require the

appliance to be extracted from

cabinet.

Remove the grid of the drip tray to

easily pull out the Refreshment

Centre. After extracting the appliance,

place the grid back in its original

position.

Electrical connection

Warning Before starting the plug-in,

make sure voltage and frequency

match the related information on the

rating plate and on the technical

specifications table.

Warning Make sure the main switch

is in off position

Connect the appliance to the socket using

the supplied cord.

When necessary, extract momentarily the

power cord from the safety clip to make

the connection to the power socket easier.

Fix the supplied cord to the clip on the

right side of appliance.

1 230V AC Socket

2 Clip to fix cord

10 electrolux

Secure water discharge tap

Warning Water leakage will occur

when the discharge tap is open

Warning Close the water discharge

tap if open.

A red safety screw prevents the accidental

opening of the tap.

During regular appliance operation, when

not otherwise indicated, the tap shall be

closed and the screw inserted.

1 Water discharge tap

2 Safety screw

Water mains connection

Warning Provided inlet hose can

reach a maximum distance of 4

meters from the water mains. In

alternative, extra long tubes need to

be used

Warning It is necessary to place a tap

between the water mains and the

water inlet hose

Warning Connect only to potable cold

water mains

Warning All water mains connections

must be carried out by a certified

plumber

Warning Use only the new hose-sets

included in the package

Warning Do not reuse old hose-sets

Screw the hose to water inlet rotating it

clockwise, then connect the hose to the

water mains.

1 Water inlet 3/4”

Filter cartridge first installation

Warning Make sure there are no

water leaks

Warning Dry well the base of the

appliance before installing it into the

cabinet

The head of the filter cartridge is on the

left side of the appliance.

Remove the cap from the filter cartridge,

hold the filter head tight and insert the new

filter cartridge in the head by pushing it up

and rotating it counter-clockwise.

1 Filter head

2 Filter cartridge

Pressure reducer first installation

Warning Do not open the pressure

reducer during unit connection

1 CO₂ tube

2 CO₂ fitting

electrolux 11

Pull out the CO₂-labeled tube and its

fitting placed on the left side of the

appliance and then insert the fitting in the

CO₂ pressure reducer.

CO₂ bottle first installation

Warning While screwing on the new

CO₂ bottle, CO₂ leaks might occur

The CO₂ bottle is placed on the left side of

the appliance.

The appliance can operate with both

disposable and rechargeable CO₂ bottles.

With disposable CO₂ bottles

1. Remove the plastic cap

2. Screw the bottle rotating it clockwise

on the pressure reducer

With rechargeable CO₂ bottles, an

adapting junction is provided with the

pressure reducer.

1. Screw the adapting junction rotating it

clockwise on the pressure reducer

2. Screw the bottle rotating it clockwise

on the adapting junction

Make sure the CO₂ bottle is tightly fixed.

1. Lock the bottle in the bottle holder on

the left side of the appliance

2. Fix the holder with the provided safety

strip

Usage

Front touch control panel

Warning To prevent damages to the

touch control panel, do not touch it

with wet or oily hands

1 Empty CO₂ bottle LED

2 Power LED (to be used also during

water tank draining)

3 Ambient water LED

4 Cold sparkling water LED

5 Cold still water LED

6 Ice shards LED

7 Light LED

8 Filter LED

12 electrolux

First Start-up

Warning Dispense 3 litres of cold still

water and 1 litre of cold sparkling

water to rinse out well the water coils

Turn on the appliance using the power

switch placed on the right side of the

appliance.

The power LED will start flashing.

When the power LED stops flashing, the

touch control panel becomes active.

When using the Refreshment Centre for

the first time you need to wait 5 hours

before the appliance provides full

operating results.

During this period of time the

appliance is working but with limited

performance.

The above procedure needs to be

followed also after extended inactive

period of time.

Regulate water inlet pressure

Warning The pressure reducer must

be opened only when the installation

process is complete and the appliance

is switched on

1 Water plastic knob

2 Water pressure gauge

Make sure that the tap between the water

mains and the flexible hose is open.

After any pressure regulation, verify the

new adjusted level by dispensing a little

water.

Pressure has to be regulated between 2

and 3 bar operating on the plastic knob.

To regulate the pressure, pull up the water

plastic knob.

While dispensing ambient water: for

pressure increase rotate the knob

clockwise, for pressure decrease rotate it

counter-clockwise.

Once the regulation has been made, push

the knob back to its security position.

Regulate CO₂ pressure

Warning The pressure reducer must

be opened only when the connection

process is complete and the appliance

is powered up

Warning When changing CO₂

pressure, the adjusted sparkling level

will be reached after dispensing 0.5

litres of cold sparkling water

Warning CO₂ pressure can be

adjusted to a maximum of 4 bar

1 CO₂ plastic knob

2 CO₂ pressure gauge

CO₂ pressure can be adjusted using the

pressure reducer placed on the CO₂

bottle.

Pressure has to be regulated 0.5 bar

above inlet water value operating on the

CO₂ plastic knob.

For pressure increase rotate the knob

clockwise, for pressure decrease rotate it

counter-clockwise.

electrolux 13

Dispensing during first start-up

During first start-up ambient water is

immediately ready.

The first ice shards will be ready after 90

minutes.

The ideal temperature for cold water will

be reached after 2.5 hours.

The ice tank will be fully loaded after 5

hours.

Dispensing during normal usage

Warning Do not insert any object in

the ice shards nozzle. This may

damage the section with consequent

ice melting

In order to fill a big bottle or jug,

carefully pull out the water dispense

nozzle.

Place a glass on the drip tray, then select

the desired beverage or the ice shards.

Press the icon until the desired amount

has been dispensed.

Dispensing is indicated by the LED

corresponding to the pressed icon.

Dispensing from water nozzle is delayed

to prevent accidental leakage.

The appliance can dispense 2 litres of cold

still or cold sparkling water in 2 hours.

The water coolness level may vary if

the dispensing time recommendations

are not followed.

If the ice has been entirely dispensed,

fresh ice shards will be available after

approximately 40 minutes.

The ice tank will be fully loaded after 2.5

hours.

Illumination of the Refreshment Centre

For a more comfortable dispensing

process, press the light LED of the control

panel and switch on the central ambient

light.

Maintenance and cleaning

Warning If the appliance remains

switched off for over 8 hours it is

necessary to drain the water tank

Warning A monthly drainage of the

water tank is needed to guarantee the

correct quality level

Warning Carry out a cleaning of the

appliance every six months to ensure

the correct quality level

Warning Use food grade CO₂ bottle

Drainage of the drip tray

To prevent water leakage, keep the drip

tray clean and dry.

14 electrolux

Drainage of the water tank

Warning If you had to stop pressing

the power icon, please press it again

and keep it pressed in order to

complete the step

Warning After the procedure always

remember to close the water

discharge tap to avoid water leakage

1. Dispense all the available ice shards

2. Remove the grid of the drip tray to

easily pull out the Refreshment Centre.

After extracting the appliance, place

the grid back in its original position

3. Connect the plastic hose to the

discharge water nozzle

4. Place a big container underneath the

plastic hose or put the hose in a sink

5. Press the power icon until power LED

starts flashing

6. Remove the safety screw and open the

water discharge tap

7. Press the power icon again and keep it

pressed until the power LED stops

flashing

8. Close the water discharge tap and

reinsert the safety screw

9. Restart the appliance using the power

switch

10.Push back the appliance until it is

locked into position

Food grade CO₂ bottle replacement

Warning While screwing on the new

CO₂ bottle, CO₂ leaks might occur

1. Remove the grid of the drip tray to

easily pull out the Refreshment Centre.

After extracting the appliance, place

the grid back in its original position

2. Remove the safety strip of the CO₂

holder to extract the used bottle

3. Hold the pressure reducer and turn the

CO₂ bottle clockwise

4. Screw the new bottle, counter-

clockwise, into the pressure reducer

5. Secure the new CO₂ bottle to its holder

and fix it with the provided safety strip

6. Push back the appliance until it is

locked into position

Filter cartridge replacement

Warning In case of water leakage dry

the base carefully

Warning Lay a cloth under the filter

cartridge to prevent the base from

getting wet

electrolux 15

1. Remove the grid of the drip tray to

easily pull out the Refreshment Centre.

After extracting the appliance, place

the grid back in its original position

2. Turn off the appliance using the power

switch

Water may come out from the filter

cartridge, therefore place a cloth on

the filter head and cartridge to prevent

the cabinet from getting wet.

If there is water on the base, dry it

carefully.

3. Rotate the used filter cartridge

clockwise and pull it down to extract it

4. Insert the new filter cartridge in the

filter head by pushing it up and rotating

it counter-clockwise

5. Turn on the power switch

6. Immediately press the ambient water

icon and keep it pressed until LEDs

start scanning.

Wait for all LEDs to turn off before

proceeding with the next step

If the power LED becomes steady,

please repeat the last two steps until

LEDs start scanning.

7. Restart the appliance using the power

switch

8. Push back the appliance until it is

locked into position

9. Dispense 3 litres of cold still water

10.Dispense 1 litre of cold sparkling water

Cleaning of the inlet filter

1 Water inlet and inlet filter housing

Carry out this procedure on a yearly basis.

1. Close the water mains

2. Dispense ambient water until it stops

coming out

3. Remove the grid of the drip tray to

easily pull out the Refreshment Centre.

After extracting the appliance, place

the grid back in its original position

4. Rotate the filter cartridge clockwise and

pull it down to extract it

5. Take out the water inlet hose

6. Extract the inlet filter with rounded-jaw

pliers

7. Clean the inlet filter

8. Insert the inlet filter and place it in its

original position

9. Insert the water inlet hose and place it

in its original position

16 electrolux

10.Insert the filter cartridge in the filter

head by pushing it up and rotating it

counter-clockwise

11.Push back the appliance until it is

locked into position

12.Open the water mains

Cleaning

Warning Do not dispense cold

sparkling water during the cleaning

procedure

Warning After the procedure always

remember to close the water

discharge tap to avoid water leakage

Warning Remove the water

dispensed during cleaning process

Warning In case of water leakage dry

the base carefully

Warning Lay a cloth under the filter

cartridge to prevent the base from

getting wet

During cleaning process two kinds of LED

signals are shown:

• Flashing power LED:

waiting for user input

• Scanning LEDs, from power to light

LED:

working on cleaning, wait for the power

LED to flash

1. Dispense all the ice shards

2. Remove the grid of the drip tray to

easily pull out the Refreshment Centre.

After extracting the appliance, place

the grid back in its original position

3. Turn off the appliance using the power

switch

Water may come out from the filter

cartridge, therefore place a cloth on

the filter head and cartridge to prevent

the cabinet from getting wet.

If there is water on the base, dry it

carefully.

4. Rotate the filter cartridge clockwise and

pull it down to extract it

5. Open the cleaning cartridge and fill it

with “Neutral Detergent”

6. Hold the cleaning cartridge from the

upper larger side and insert it in the

filter head by pushing it up and rotating

it counter-clockwise

7. Connect the plastic hose to the

discharge water nozzle

8. Place a big container underneath the

plastic hose or put the hose in a sink

9. Place a cup under the water dispense

nozzle

10.Remove the safety screw and open the

water discharge tap

electrolux 17

11.Turn on the power switch

12.Immediately press the light icon and

keep it pressed until LEDs start

scanning

If the power LED became steady,

please repeat the two last steps until

LEDs start scanning

13.Wait for the power LED to flash, then

press the power icon until the LEDs

start scanning again

Some water will be dispensed from

the water dispenser automatically

14.Wait for the power LED to flash, then

remove the cleaning cartridge

Water may come out from the

cleaning cartridge.

If there is water on the base, dry it

carefully.

15.Insert the filter cartridge in the filter

head by pushing it up and rotating it

counter-clockwise

16.Press the power icon until LEDs start

scanning again

17.Wait for the power LED to flash, then

press the power icon until all LEDs

start scanning.

Wait for all LEDs to turn off before

proceeding with the next step

Some water will be dispensed from

the water dispenser automatically

18.Close the water discharge tap and

reinsert the safety screw

19.Restart the appliance using the power

switch

20.Push back the appliance until it is

locked into position

21.Dispense 3 litres of cold still water

22.Dispense 1 litre of cold sparkling water

23.Dispense all ice shards

Signals for users

Signals for users on the front panel

LED type Message

Power LED

Flashing LED:

• Appliance preparation to start-up

Steady LED:

• Power on signal

Filter LED

Flashing LED:

• There are 40 litres left before a new filter

cartridge is needed

Steady LED:

• Change the filter cartridge, there are 5 litres

left before safety lock of the appliance

• Check “Maintenance and cleaning” chapter

CO₂ bottle LED

Steady LED:

• Cold sparkling water is disabled

• CO₂ bottle is empty or missing

• Check “Maintenance and cleaning” chapter

Six LEDs alarm

6 flashing LEDs (except filter and CO₂ bottle)

Check “What to do if...” chapter

18 electrolux

What to do if...

Warning All repairs should be carried out by authorised technicians

Problem Cause Resolution

Cold sparkling water sprays

CO₂ gas

Carbonator limit reached Stop the dispensing and wait 20

seconds, then start dispensing

again

Water is not dispensed No water supply Check water supply

Inlet water low pressure Check water inlet pressure

Small ice shards No water supply Check water supply

Low pressure of inlet water Check water inlet pressure

Low carbonation level Low CO₂ pressure Check CO₂ pressure

Brand new appliance Use for 1 week

After a week Call technical assistance

No cold water, no shards

available 3 hours after starting

the appliance

Cooling system Call technical assistance

Cold still water sprays CO₂ gas Carbonating system Call technical assistance

Six LEDs alarm troubleshooting

All operations below require for the

appliance to be switched on and

extracted from cabinet.

Pull out the Refreshment Centre and

proceed as follows

• Check water supply

• Check water inlet pressure

• Check CO₂ pressure

• Water leakage check

• Cold restart

If none of the procedures turns off the

alarm or resolve your problem, close the

inlet water and call the Assistance.

Check water supply

Check if the tap between the water mains

and the water inlet hose is open or water

is coming out from other taps in the house.

When water comes out and the water

mains work properly, proceed with the

step Check water inlet pressure.

If your water mains connection does not

work properly, please have it checked.

Check water inlet pressure

Warning It is recommended to check

the CO₂ pressure value when

changing the water inlet pressure

For further information see the

chapter on first installation.

Pressure can be checked using the water

pressure reducer with gauge.

Pressure has to be regulated between 2

and 3 bar.

Check CO₂ pressure

Warning Never exceed the indicated

inlet value

For further information see the

chapter on first installation.

Please check the gauge while dispensing

cold sparkling water.

Pressure has to be regulated 0.5 bar

above inlet water value operating on the

CO₂ plastic knob.

Water leakage check

Warning If water covers the whole

base, please turn off the appliance,

close the inlet water and call the

Assistance.

electrolux 19

Check if there is water inside the base,

especially near water leakage sensors,

then dry it carefully.

1 Left rear side water leakage sensor

2 Right rear side water leakage sensor

3 Left middle side water leakage sensor

Cold restart

Turn off the appliance for 30 minutes, then

turn it on again.

Environment concerns

The symbol on the product or on its

packaging indicates that this product

should not be treated as household waste.

It should be taken to the appropriate

collection point for the recycling of

electrical and electronic equipment. By

ensuring this product is disposed of

correctly, you will help prevent potential

negative consequences for the

environment and human health, which

could otherwise be caused by

inappropriate waste handling of this

product. For more detailed information

about recycling of this product, please

contact your local council, your household

waste disposal service or the shop where

you purchased the product.

Packaging material

The packaging materials are

environmentally friendly and can be

recycled. The plastic components are

identified by markings, e.g. >PE<, >PS<,

etc. Please dispose of the packaging

materials in the appropriate container at

the community waste disposal facilities.

Warning When the appliance is no

longer being used:

• Pull the plug out of the socket.

• Cut off cord and plug before the

disposal.

www.electrolux.com

942490226 – 00 – 112009

Electrolux EIW63810X User manual

Electrolux EIW63810X User manual

Electrolux EIW63810X User manual

Related papers

Other documents