1.
3.
4.
5. 6.
2.
B0400 PRIVACY SET ONLY
B0100 LEVERSETS
Installation Instructions
B0100 LEVERSETS Installation Instructions www.entro.com.au
Print to Actual Size A4
Fold on Door Edge
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
41mm
Fold on Door Edge
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
a.
2x Ø5mm
Ø25mm
Drill holes through the
door where through bolt
fixing is required
41mm
CL
a.
b.
c.
Fold on Door Edge
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
41mm
CL
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
a.
b.
c.
Fold on Door Edge
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
41mm
CL
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
a.
b.
c.
Fold on Door Edge
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
a.
b.
c.
Fold on Door Edge
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
41mm
Fold on Door Edge
a.
Fold on Door Edge
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
41mm
CL
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
60mm Backset 2x Ø5mm
Ø8mm
Ø25mm
Drill a Ø8mm hole
only when installing
a privacy latch (B0400)
Drill a Ø25mm hole at
60mm backset through
the door for passage set Drill holes through the
door where through bolt
fixing is required
20.5mm
ion Template
41mm
Fold on Door Edge
Handle & Latch Preparat
a.
b.
c.
LEVERSET
& LATCH
PREPARATION
TEMPLATE
Fold template on door edge with centre line
at desired height (approx 1000mm from
floor). Mark holes ready for drilling.
Drill 2mm pilot holes for the furniture
from both side of the doors.
Drill 25mm latch hole (a.) to 80mm depth.
Drill 25mm & 5mm furniture holes (b.) from
both sides of the door. Additional 8mm hole
(c.) when installing privacy latch (B0400).
If handing is required for the privacy latch
(eg open out doors), pull latch & rotate.
Insert latch into 25mm hole & mark
around latch plate. Chisel out recess and
ensure faceplate is flush with the door
face.
Drill 2x 2mm pilot holes and affix with
screws provided.
door where through bolt
b.
c.
Drill holes through the
door where through bolt
b.
c.
B0100 LEVERSETS
Installation Instructions
B0100 LEVERSETS Installation Instructions www.entro.com.au
Print to Actual Size A4
7.
12.
8.
13.
9.
14
10.
15.
11.
Insert spindle (a.) through tubular
latch with ends evenly spaced on
both sides of the door. Insert
spindle springs (b.) into each lever.
B0400 Privacy Set Only: Use split
spindle supplied in B0400 set.
Ensure split spindle is released by
1/2 turn before installing.
a.
b.
Remove lever rose covers ready
for installation. Vertically insert 2x
fixing cap nuts (a.) into external
side lever. Compress both levers
against the door evenly engaging
the spindle. Insert fixing screws
(b.) through the internal side
lever. Lightly fasten fixing screws
and check levers are horizontal
and in line with the latch before
firmly tightening.
Pass the lever rose covers (a.)
over the levers and push to secure.
For square rose covers ensure the
small internal protrusion lines up
with the notch (b.) in the rose
plate.
a.
B0400 PRIVACY SET ONLY B0400 PRIVACY SET ONLY
On the external side of door
align the emergency access
hole (a.) over the rose cover
and furniture.
a.
On the internal side of the door,
fix the the privacy pin (a.)
through the rose cover hole
ensuring it engages with the
privacy tubular latch. Test the
privacy latch by depressing the
privacy pin and test the external
lever is locked. Test the privacy
pin releases when rotating the
internal lever.
For Mortice Lock installation,
refer to A0100SSSM instructions
and door template.
Insert 2x mortice lock spindles
(a.) through the large hole on
each side of the door. Insert
spindle springs (b.) into each
lever.
a.
b.
Remove lever rose covers ready for installation. Horizontally insert the fixing
cap nuts (a.) into the external lever. Compress the levers against the door
evenly, ensuring the spindles engage both levers. Insert only 1x fixing screw
(b.) through the internal leverset and lightly fasten to the external fixing cap
nut. Rotate the lever to provide access for the 2nd fixing screw. Insert the 2nd
fixing screw (c.) through the internal lever and lightly fasten fixing screw.
Check levers are both horizontal before firmly tightening fixing screws.
Pass the lever rose covers (b.)
over the levers and push to
secure. For square rose covers
ensure the small internal
protrusion lines up with the notch
(b.) in the rose plate.
a.
b.
a.
b.
b.
c.
a.
a.
b.
/
