ALLEGION 2821 Series User manual

Type
User manual

ALLEGION 2821 Series dummy levers are designed for interior doors, providing a stylish and functional door handle solution. Their key features include:

  • Easy installation: The levers come with a detailed instruction manual and all necessary mounting hardware, making the installation process straightforward and hassle-free.

  • Durability: Constructed from high-quality materials, the levers are built to withstand everyday use and maintain their appearance over time.

  • Versatile design: The levers feature a sleek and modern design that complements a wide range of interior décor styles, from traditional to contemporary.

ALLEGION 2821 Series dummy levers are designed for interior doors, providing a stylish and functional door handle solution. Their key features include:

  • Easy installation: The levers come with a detailed instruction manual and all necessary mounting hardware, making the installation process straightforward and hassle-free.

  • Durability: Constructed from high-quality materials, the levers are built to withstand everyday use and maintain their appearance over time.

  • Versatile design: The levers feature a sleek and modern design that complements a wide range of interior décor styles, from traditional to contemporary.

ORIGINATION CRM GSH 853 1012
AT 000
Fit here on door edge
Fit here on door edge
BACKSET 60mm
BACKSET 70mm
Mark centre-line
of latch hole
Mark centre-line
of latch hole
FOLD HERE
Installation template
for dummy applications
Installation Instructions for 2821 & 2921
Series Dummy Lever
NOTE: Carefully follow these instructions when installing.
Screws to be tightened to a recommended 2.5Nm torque.
Step 1.
Step 2.
Install lever assemblies to door:
• Remove rosette cover (1a or 1b) from lever assembly.
• Place dummy lever assembly (2) with latch alignment posts (3) against door
face.
• Place dummy plate (4) into position, on back of door.
• Fasten lever assembly & dummy plate together with screws (5) & tube nuts (6)
provided: Use long screws for thick doors and short screws for thin doors.
• Install screws (5) from dummy plate side into the vertical tube nut holes (8) of
the dummy leverset under-rose. Then tighten both screw heads.
2921
• Reapply rosette cover (1a) to under-rose by pushing the cover over the rubber
ring until flush with door.
2821
• Reapply rosette cover (1b) to under-rose by pushing the cover
over the rubber ring until flush with door. The *grub-screw, which is
already located in the rosette cover, should be on the lower face.
• Check the rosette cover is square with the door edge. Fasten in place
with *grub-screw using allen key (9) provided.
*Note: Grub-screw is already located in the rosette cover.
25mm hole
x 10mm deep
9mm hole
Important Note:
Don’t drill this hole
through the door.
55R1DOC04GH1 JAN 22
• Fold Template where indicated.
• Position template on door edge at desired height.
• Firmly hold template & mark 5 hole centres (4 off 9mm
& 1 off 25mm) at required backset.
Note: 25mm hole 10mm deep only.
• Drill Pilot holes - suggest 3mm, then enlarge (4 off) 9mm
holes from both sides of door.
• Drill (1 off) 25mm hole 10mm deep on side of door
dummy leverset will be fitted.
1b
1a
9
2
3
6
4
5
8
  • Page 1 1

ALLEGION 2821 Series User manual

Type
User manual

ALLEGION 2821 Series dummy levers are designed for interior doors, providing a stylish and functional door handle solution. Their key features include:

  • Easy installation: The levers come with a detailed instruction manual and all necessary mounting hardware, making the installation process straightforward and hassle-free.

  • Durability: Constructed from high-quality materials, the levers are built to withstand everyday use and maintain their appearance over time.

  • Versatile design: The levers feature a sleek and modern design that complements a wide range of interior décor styles, from traditional to contemporary.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI