AMG AMG2263 Instruction Sheet

Type
Instruction Sheet

This manual is also suitable for

AMG AMG2263L is a Standalone Long Distance Video Transmitter and Bi-directional 20mA Current Loop Data Transceiver which supports the following features:

  • Video Transmission: Transmits video signals over long distances using optical fiber cables. Supports video frequencies from 10Hz to 6MHz.
  • Bi-directional 20mA Current Loop Data: Allows for the transmission and reception of data using a 20mA current loop interface.
  • Opto OUT and Opto IN: Provides optical input and output connectors for fiber optic connections.
  • Power Supply: Operates on a power supply ranging from +12 volts to +18 volts at 250mA.

AMG AMG2263L is a Standalone Long Distance Video Transmitter and Bi-directional 20mA Current Loop Data Transceiver which supports the following features:

  • Video Transmission: Transmits video signals over long distances using optical fiber cables. Supports video frequencies from 10Hz to 6MHz.
  • Bi-directional 20mA Current Loop Data: Allows for the transmission and reception of data using a 20mA current loop interface.
  • Opto OUT and Opto IN: Provides optical input and output connectors for fiber optic connections.
  • Power Supply: Operates on a power supply ranging from +12 volts to +18 volts at 250mA.
AMG Systems Ltd. reserves the right to make changes to this document without notice.
The information herein is believed to be accurate. No responsibility however is assumed
by AMG for its use.
Page 1 of 2 D04540-00
AMG2263L
Instruction Sheet
AMG2263 Standalone Long Distance Video Transmit + Bi-directional 20mA Current
Loop Data
Video Connection
Connectors ...........................75 ohm BNC Socket.
Input Impedance...................75 ohm terminated.
Input Level ...........................1 volt p-p nominal.
Frequency Response.............10Hz to 6MHz min.
Optical Connection
Connectors............................ST Style (2 off)
Opto Out Launch Power
50/125............................-20dBm. min.
62.5/125.........................-17dBm min.
Wavelength...........................1300nm nominal.
Data Connection
Connector .............................Push-in connector strip- 14way
(Solid conductors 0.5mm2(20 awg) can be connected by simply push fitting
into the appropriate connection hole. Smaller conductors and wires (up to
0.5mm2, 20 awg) are inserted into the connection space whilst depressing the
orange lever. Wire or conductors should be stripped back to a length of
11mm. Use a small screwdriver to depress the orange lever to release the
connection.)
VIDEO INPUT Opto OUT
(Single Fibre not fitted
Opto IN
(IN/OUT Single Fibre)
SYSTEM 2000
VIDEO
TRANSCEIVER
134mm
148mm
7mm
39.5mm
79mm A A
PL1
PIN 1
PIN 14
AMG Systems Ltd. reserves the right to make changes to this document without notice.
The information herein is believed to be accurate. No responsibility however is assumed
by AMG for its use.
Page 2 of 2 D04540-00
Pinout ...................................See Below Note Pins number from the BNC Connector
Pin No. Function
1 N/C
2 N/C
3 Power Ground
4 Power Input (+12v to +18v dc )
5 Ground
6 N/C
Data
Interface 20mA
7 Data Ground
8 Data Out
9 Data In
10 N/C
11 N/C
12 Ground
13 N/C
14 N/C
Power Supply
Supply...................................+12 volt to +18 volt at 250mA
Connection ...........................Connector Strip
Pin 3 Gnd, Pin 4 Power Input
Dimensions
See Drawing Above
Mounting Details
See Drawing Above
  • Page 1 1
  • Page 2 2

AMG AMG2263 Instruction Sheet

Type
Instruction Sheet
This manual is also suitable for

AMG AMG2263L is a Standalone Long Distance Video Transmitter and Bi-directional 20mA Current Loop Data Transceiver which supports the following features:

  • Video Transmission: Transmits video signals over long distances using optical fiber cables. Supports video frequencies from 10Hz to 6MHz.
  • Bi-directional 20mA Current Loop Data: Allows for the transmission and reception of data using a 20mA current loop interface.
  • Opto OUT and Opto IN: Provides optical input and output connectors for fiber optic connections.
  • Power Supply: Operates on a power supply ranging from +12 volts to +18 volts at 250mA.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI