AMG AMG2263S
The AMG AMG2263S is a standalone single-fiber video transmitter with a bidirectional 20mA current loop. It provides the following capabilities:
- Video transmission over a single fiber optic cable
- Transmission of video signals with a frequency response of 10Hz to 6MHz
- Optical connection using an ST style connector
- Data transmission using a 14-way push-in connector strip
- Power supply of +12 volt to +18 volt at 250mA
This device can be used in various applications, including:
- CCTV systems
- Industrial automation
- Medical imaging
- Remote monitoring
AMG AMG2263S
The AMG AMG2263S is a standalone single-fiber video transmitter with a bidirectional 20mA current loop. It provides the following capabilities:
- Video transmission over a single fiber optic cable
- Transmission of video signals with a frequency response of 10Hz to 6MHz
- Optical connection using an ST style connector
- Data transmission using a 14-way push-in connector strip
- Power supply of +12 volt to +18 volt at 250mA
This device can be used in various applications, including:
- CCTV systems
- Industrial automation
- Medical imaging
- Remote monitoring
AMG Systems Ltd. reserves the right to make changes to this document without notice.
The information herein is believed to be accurate. No responsibility however is assumed
by AMG for its use.
Page 1 of 2 D04069-02
AMG2263S
Instruction Sheet
AMG2263S Standalone Single Fibre Video TX + Bi-directional 20mA Current Loop
Data
Video Connection
Connectors ...........................75 ohm BNC Socket.
Input Impedance...................75 ohm terminated.
Input Level ...........................1 volt p-p nominal.
Frequency Response............. 10Hz to 6MHz min.
Optical Connection
Connectors............................ST Style (1 off)
Opto Out Launch Power
50/125............................-20dBm. min.
62.5/125.........................-17dBm min.
Wavelength...........................850/1300nm nominal. (single fibre)
Data Connection
Connector .............................Push-in connector strip - 14way
(Solid conductors 0.5mm2(20 awg) can be connected by simply push fitting
into the appropriate connection hole. Smaller conductors and wires (up to
0.5mm2, 20 awg) are inserted into the connection space whilst depressing the
orange lever. Wire or conductors should be stripped back to a length of
11mm. Use a small screwdriver to depress the orange lever to release the
connection.)
VIDEO INPUT Opto OUT
(Single Fibre not fitted
Opto IN
(IN/OUT Single Fibre)
SYSTEM 2000
Video
Transceiver
134mm
148mm
7mm
39.5mm
79mm A A
PL1
PIN 1
PIN 14
AMG Systems Ltd. reserves the right to make changes to this document without notice.
The information herein is believed to be accurate. No responsibility however is assumed
by AMG for its use.
Page 2 of 2 D04069-02
Pinout ...................................See Below – Note Pins number from the BNC connector
Pin No. Function
1 N/C
2 N/C
3 Power Ground
4 Power Input (+12v to +18v dc )
5 Ground
6 N/C
Data
Interface 20mA
7 Data Ground
8 Data Out
9 Data In
10 N/C
11 N/C
12 Ground
13 N/C
14 N/C
Power Supply
Supply...................................+12 volt to +18 volt at 250mA
Connection ...........................Connector Strip
Pin 3 Gnd, Pin 4 Power Input
Dimensions
See Drawing Above
Mounting Details
See Drawing Above
-
1
-
2
AMG AMG2263S
The AMG AMG2263S is a standalone single-fiber video transmitter with a bidirectional 20mA current loop. It provides the following capabilities:
- Video transmission over a single fiber optic cable
- Transmission of video signals with a frequency response of 10Hz to 6MHz
- Optical connection using an ST style connector
- Data transmission using a 14-way push-in connector strip
- Power supply of +12 volt to +18 volt at 250mA
This device can be used in various applications, including:
- CCTV systems
- Industrial automation
- Medical imaging
- Remote monitoring
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
AMG AMG2263 Instruction Sheet
-
-
-
-
-
-
-
-
-