Beghelli CASTEX 320 (HZ-CAS320) Installation guide

Beghelli
Brand
Beghelli
Model
CASTEX 320 (HZ-CAS320)
Type
Installation guide
CASTEX 320
Page 1 of 3
Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (954) 442-6600
04/21/22
When using electrical equipment, basic safety precautions should always be followed including:
1. Disconnect power before performing work on electrical equipment.
2. Do not mount near gas or electric heaters.
3. Equipment should be mounted in locations and at heights where it will not be subjected to
tampering.
4. The use of accessory equipment not recommended by Beghelli Inc., may cause an unsafe
condition, and will void the unit’s warranty.
5. Do not use this equipment for other than its intended purpose.
6. Servicing of this equipment should be performed by a qualied service personnel.
7. Suitable for non-insulated surface and frame. DO NOT cover xture with insulation liner or
similar material.
8. DO NOT install in unstable, loose or breakable surfaces.
9. DO NOT let objects impact or exert force on the surface of the xture.
10. SAVE THESE INSTRUCTIONS!
Fixtures must be wired in accordance with National electrical code and all applicable local codes.
Proper grounding is required for safety.
This product must be installed in accordance with the applicable installation code by a qualied
electrician who is familiar with the construction and operation of the product and the hazards
involved.
IMPORTANT SAFEGUARDS
Read & Follow All Safety Instructions
INSTALLATION INSTRUCTIONS
CASTEX 320
Page 2 of 3
Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (954) 442-6600
04/21/22
WARNING
Risk of fire, electric shock or personal injury
Before installation, turn off power!
INSTALLATION STEPS (For Class I Div. 1 Group C, D Locations)
1. Dis-assemble the light as pictured above, ready for
Class I Div. 1 Groups C, D.
2. Drill two 10mm holes 120mm apart. Use the holes
to thread the ø10 expanded screws and ax the
bracket on chosen surface.
13# SPANNER
Dim-
Dim+
N
G
L45mm
5# ALLEN KEY 45mm
6# ALLEN KEY
2x Fixing
M8 screw
3. Attach the light to hazardous location conduit.
Connect the AC; connect the Live wire to black,
Neutral wire to white, and grounding wire to green.
For dimming; connect the Dim+ wire to purple and
Dim- wire to gray. Close the power enclosure.
4. Install the xture to ceiling or wall, adjust the light
angle, and tighten the xing screw. Turn on the
power to test that the light is working.
CASTEX 320
Page 3 of 3
Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (954) 442-6600
04/21/22
WARNING
Risk of fire, electric shock or personal injury
Before installation, turn off power!
INSTALLATION STEPS (For Class I Div. 2 Group A, B, C, D Locations)
1. Unpack the xture and accessories and tighten
both angle holder screws as shown above.
2. Thread the cable through the exible metal conduit
and tighten it to the xture.
Dim-
Dim+
N
G
L
3. Drill two holes as shown above, 91~140mm apart.
Use ø10 expanded screws to install mounting
bracket on chosen surface.
4. Connect the AC cable. Black cable to Live wire,
white cable to Neutral wire, green cable to ground.
Dim+ to purple, Dim- to gray.
2x Fixing screw
Flexible metal conduit
  • Page 1 1
  • Page 2 2
  • Page 3 3

Beghelli CASTEX 320 (HZ-CAS320) Installation guide

Beghelli
Brand
Beghelli
Model
CASTEX 320 (HZ-CAS320)
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers