Midmark Artizan® Expressions Operatory Cabinetry - X-ray Pass Through Installation guide

Type
Installation guide
1
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
TP201 20-42-FO-00013 Rev A1 C2169
003-10234-00 Rev. AA1 (10/19/18)
Applies to Models:
XPC4050, XPC4850
Special Tools:
none
Language of origin: English
Note
Refer to manufacturer manual
for X-ray equipment installation.
ARTIZAN EXPRESSIONS X-RAY PASS THROUGH CABINET
Style G
Intended Use:
This product is intended to be installed through the wall dividing two dental exam rooms. It is
intended to house an intra-oral X-ray mounted through the shell of the cabinet into a wall stud.
midmark.com
2
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10234-00
TP201 20-42-FO-00013 Rev A1 C2169
Artizan Expressions X-ray Pass Through Cabinet
Rough-in Information (Carpenter/Contractor)
Note
The rough-in opening for the Artizan Expressions
X-ray Pass Through Cabinet is typically made
in the wall between two dental exam rooms and
constructed similar to a rough window opening.
It is important to always double the studs on the
mounting side of the opening to ensure that the
X-ray equipment will be supported.
Note
Rough opening must be plumb
and square and have a
minimum opening of the listed
sizes to ensure proper fit.
Equipment Alert
This cabinet is not intended to
solely support any X-ray machine.
Always install X-ray equipment through the
cabinet into the building structure.
52 3/8”
Note: Check X-ray mounting
template for exact conduit
height location.
39”
Dimension A:
XCP4050 = 42 3/8”
XCP4850 = 50 3/8”
midmark.com
3
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10234-00
TP201 20-42-FO-00013 Rev A1 C2169
Installation (XPC)
Side Panel
Spreading
Bolt
Connector Housing
Bottom Indicator Hole
Step 1: Assemble Cabinet Shell.
A) Identify side and bottom panels and hardware. Side panels are oriented with a center indicator hole at the
bottom of the panel. Top and Bottom panels are oriented with holes pointed towards the floor.
B) Insert spreading bolt into the holes nearest the outside vertical edge of the side panel.
C) Insert dowels in the top and bottom panels into the side panels. Spreading bolts will then be concealed
inside the top and bottom panels. Push all of the box sides together until they are flush.
D) Insert the connector housing into the bottom of the top and bottom panels until they are flush with the panel.
Tighten the connector housing by turning it clockwise with a screwdriver.
Connector Housing
Spreading
Bolt
midmark.com
4
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10234-00
TP201 20-42-FO-00013 Rev A1 C2169
Installation (XPC)
Step 2: Install Cabinet Shell.
A) Lift the shell into the rough opening.
B) Push the shell against the stud to which the X-ray equipment
will be mounted.
C) Level and secure the bottom panel and the side to which the
X-ray equipment will be mounted using the provided wood
shims and 2 ½” screws (12).
D) Check the level on the top panel and other side panel.
Fill empty space near the mounting holes with wood shims
and trim excess wood.
E) Once all screws are in place, cover the screw heads with the
provided adhesive cover caps.
Step 3: Install Doors.
A) Adjust each hinge to be fully extended by turning each adjustment
screw clockwise until adjustment limit has been reached
B) Lift the doors and clip hinges into hinge base plates. Make sure
each hinge is fully engaged.
C) Adjust the hinges until doors are in desired location. See hinge
adjustment in this manual for more information.
Shim
Wood
Screw
Adhesive
Cover Cap
2
1
midmark.com
5
© 2018 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10234-00
TP201 20-42-FO-00013 Rev A1 C2169
Installation (XPC)
Step 4: Install Trim Kit (Optional).
A) Using the provided 2 ½” screws (12), attach optional trim kit
components around the unit beginning with the top and
working around the cabinet until all sides are installed.
B) Place provided adhesive cover caps over the recessed
screw heads.
C) Repeat the process for the other side of the cabinet.
Hinge Adjustment:
A) Height Adjustment.
B) Panel In/Out Adjustment.
C) Left/Right Adjustment.
A
B
C
midmark.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Midmark Artizan® Expressions Operatory Cabinetry - X-ray Pass Through Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI