QUICK START GUIDE
Niro
Download the Momentum App from the
Apple App Store or Google Play.
Connect your mobile device Wi-Fi to the
network you want your camera to be
paired to.
Important: Make sure the app you
download matches the same logo as
shown above.
Step 1: Download the app
Sign up for a new account.
Once you’ve finished entering your
information, you will receive an email
verification link.
Click on the email link to activate your
account.
Return to the app and sign in.
Step 2: Create an Account
Connect the Micro-USB cable to the
back of the camera and the power
adapter.
Plug in the power adapter to an outlet.
Micro-USB
Power Port
Step 3: Plug in Niro
IMPORTANT: Make sure your mobile device
is connected to the Wi-Fi network.
From the Momentum app, select Pair
Device.
Select the Garage Door Controller from
the list of devices.
Go to your mobile device’s Wi-Fi settings.
Connect to the ‘MOGA-001’ Wi-Fi
network.
Step 4: Pair Niro
Go back to the Momentum App.
Your Wi-Fi network will auto load, so you
will just need to enter your network
password.
(If your Wi-Fi network did not show up,
that means your mobile device was not
connected to it prior to pairing. See ‘Step 1’
for details.)
Step 5: Connect to Wi-Fi Network
It’s recommended to have Niro
mounted hanging upside down from
the bottom of your garage opener.
You may use the provided sticker and
metal plate to attach the device.
Step 6: Mount Niro
Method 1
Method
2
Unplug your garage opener.
Locate your garage wall remote console.
You should see some wires that come
out of it that lead all the way to
terminals on the back of your garage
opener.
Note: If you’re still unsure which terminals to
connect the wires to, please refer to your
garage door opener’s instruction manual to
verify.
Step 7: Connect Wires to GDO
Note: Your ports may look different from this image.
Connect Niro’s wires into the same wire
ports as your garage wall remote
console. This may require loosening the
tabs or screws depending on your garage
opener model.
Twist the two wires together into each
terminal for a better connection,
however make sure the wall console
wires go into their original terminals.
Step 7: (continued)
Press tabs to
release
Insert the other end of the wires into the
1
st
and 2
nd
terminals on the back of the
Niro device. You may need to use a tool
to push down on the buttons to release
and insert the wires.
Note: Both wires are neutral, so it doesn’t
matter which color wire goes into which of the
two ports. However, make sure the open wire
ends are not touching each other.
Step 8: Connect Wires to Niro
Plug back in your garage opener and
open the Momentum App. Select the
blue garage tile to access the garage
door control screen.
In this screen, you will get a live view of
the state of your garage. Tap the blue
button at the bottom to control the
state of your garage door.
Once you’ve confirmed the controls are
working, your setup is complete!
Step 9: Test the Controls
Light Indicators & Status
1. Solid Red – Booting
2. Slow Blinking Red – Disconnected
from Wi-Fi
3. Double Blinking Blue – Ready to
connect to Wi-Fi.
4. Blinking Blue – Connected to Wi-Fi
5. Solid Blue – Live streaming
Note: If the camera has failed to connect
to your Wi-Fi, try resetting the camera by
following these steps.
Reset
1. With the camera plugged in, hold
down the reset button in the back of
the camera for 10 seconds.
Quick Tips:
2. The camera will then start the reset
sequence. Note that the camera will
still be bound to the same
Momentum account it was initially
paired with.
3. During the reset sequence, the
camera’s indicator light will go from
solid red to double blinking blue,
which indicates that the camera is now
be ready to connected to the Wi-Fi
again.
Hold for 10 seconds
Quick Tips:
- The pairing method has been updated
for newer devices.
- If you are having trouble connecting or
using your device, please contact our
customer service team.
Toll Free: 1 888 818 0436
E-mail: [email protected]
Troubleshooting
Version 2.0
www.momentumcam.com
/
