Zippity Outdoor Products ZP19014 Installation guide

Brand
Zippity Outdoor Products
Model
ZP19014
Type
Installation guide
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at
1 877 234 6196
(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1.
Post Caps
(3)
2. Post - Left
(
1) - 3” x 3“ x 47 1/2”
3. Post - Corner
(
1) - 3” x 3“ x 47 1/2”
4. Post - Right
(
1) - 3” x 3“ x 47 1/2”
5. Board Wall
(
8) - 7/8” x 11“ x 44”
6. Ground Stake (2) - 7/8“ x 1 1/2” x 18“
7.
2 1/2” Self-Auguring Stainless Steel Screw
(10)
Tools You Will Need
• Cordless Drill
• Level
• Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Premium Vinyl Privacy Screen
(48”W x 48”H)
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Ver 1.0/110915
1
5
2
6
Ground
7
Not to Scale
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
3
4
2 in
12 in
46 in
48 in
48 in48 in
2
Identify the left and corner post as illustrated.
With a helper, slide a board down the groove until the board
bottoms out on the factory installed screw head (roughly 2”
from the bottom of the post.
Fasten each post to the board using the screws provided
through the pre-drilled holes.
Add three more boards and fasten the top board panel into
the posts as illustrated.
1
2
STEP ONE
Premium Vinyl Privacy Screen
1
2
Assemble Full Panel
Left Post
(Will have two pre-drilled
holes at the one corner and
one factory installed screw
at the bottom)
Corner Post
(Will have four pre-drilled
holes at the one corner and
two factory installed screws
at the bottom)
3
3
Top View
Ensure Board is Tight
to the Back of the
Groove in post.
Factory Installed Screws
3
STEP TWO
Premium Vinyl Privacy Screen
Repeat step 1 through 3 for the second panel as shown.
With a helper move the entire unit to intended position.
Insert the ground stake with the blade down as illustrated
into the groove of the post.
Using a piece of wood and hammer as illustrated, gently
tap the stake approximately 12” into the ground.
Tip: If your ground is hard, use your claw hammer to
loosen the soil as illustrated and add water
1
2
3
1
4
4
3
Tip: If your ground is hard,
use your claw hammer to loosen
the soil as illustrated and add
water.
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
Premium Vinyl Privacy Screen
4
Repeat for other ground stake.
Fasten both ground anchors to the posts using the screws
provided through the pre-drilled holes in each stake.
1
2
STEP THREE
1
2
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
5
10616 Bailey Road, Unit H, Cornelius NC 28031
Toll Free Phone: 1 877 234 6196 Fax: 704 631 4685
www.zippity-outdoor.com
STEP FOUR
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
1
Finish the assembly by pushing the post caps down over the
top of posts as illustrated.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Zippity Outdoor Products ZP19014 Installation guide

Brand
Zippity Outdoor Products
Model
ZP19014
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents