Label Picture Description QTY
A Left Armrest / Leg 1
B Right Armrest / Leg 1
C Seat 1
D Seat Back 1
Caution: You must read this before you proceed
Single Chair
Label Picture Description QTY
E Allen Key 1
F
Bolt
(
M6*30mm
)
5
G
Bolt
(M6*40mm)
3
H
Bolt
(M6*60mm)
3
I Washer 13
J Seat Cushion 1
K
Bolt
(
M6*20mm
)
2
L Connection 1
M Connection 1
Before Beginning Assembly:
Step 1
Step 2
Open the carton and place all the parts on a clean, non-marring surface.
ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting
positions preventing easy assembly.
The PE wicker should never be cut, but moved away from the mounting positions.
Attach Left Armrest / Leg(A) to the Seat(C) using Bolt(F) and Washer(I) with Allen Key(E)
as shown in the picture above.
Loosely tighten the Bolts.
Attach Seat Back(D) to Seat(C) using Washer(I) , Bolt(G&K) &Connection(L&M) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 4
Connect the Chair Legs(A&B) with the Seat Back(D) using Washer(I) and Bolt(H) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 3
Attach Right Armrest / Leg(B) to Seat(C) using Bolt(F) and Washer(I) with Allen Key(E ) as
shown in the picture above.
Loosely tighten the Bolts.
Place the Seat Cushion(J) on the Chair.
Your Chair is ready for use.
Step 5
Check for stability and then tighten all Bolts at all joints.
Note: DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather; in a sequential manner, gradually tighten each Bolt until all Bolts are evenly
secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Step 6
CAUTION : This table is NOT a TOY.
Keep your child / children at bay in the process of assembly.
Assembly Instructions
Table
Warnings: You must read this before you proceed.
REMINDER : In the event of unsuitability and you intend to return, please disassemble
by reversing the assembly process and where possible pack to fit into itsORIGINAL
CARTON BOX.
No. Picture Description Qty
A Table top 1
B
Legs Support Panels
(Long side)
2
C
Legs Support Panels
(Short side)
2
D Table Legs 4
No. Picture Description Qty
E Screws (M8*40MM) 13
F
Nuts 13
G
Springs Washers 13
H
Flat Washers 13
I Spanners 1
J Screwdriver 1
K Leg Levellers(Pre-attached) 5
Before Beginning Assembly:
Attach the legs to the table top.
Insert the table legs into the pre-assembled screw from above.
Affix the leg by using Flat Washers(H), Spring Washers(G) and Nuts(F) with the Spanner.
DO NOT OVERTIGHTEN NUTS.
Step 1
Unpack all parts.
To avoid any scratch and or damage to the products, place onto a clean flat soft surface.
To the underside of the table, there are 4 (four) assembly points.
Insert Screws E into these 4 (four) positions with screwdriver(J).
To the legs, there are 2 (two) assembly points on each leg.
Insert Screws E into these 8 locations for all 4 (four) legs with screwdriver(J).
TIGHTEN ALL THE SCREWs.
Step 2
G
H
E
Step 3
This next step is to assemble the leg panels to the table legs.
Attach the Legs Support Panel with 1# end to the Screws on the Legs, and then attach the
Legs Support Panel with 2# end.
Partially tighten Nuts with Flat Washers(H)+Spring Washers(G)+Nuts(F) to the screws.
Repeat the same process for all contact points of the Table Legs and the Legs Support
Panels.
Once all the Leg Support Panels are in place, tighten all nuts in a sequential manner.
Turn the table right side up.
Adjust the pre-attached leg leveller at the end of each table leg until the table is level with the
ground.
Now go back and inspect all Nuts are tighten in with the Spanner.
Do this in a sequential manner and make sure every Screw and Nut is tightly turned in.
Your table is ready for use.
Step 4
K
1#
2#
/
