Noble House 22743 Operating instructions

Brand
Noble House
Model
22743
Type
Operating instructions

This manual is also suitable for

Label Picture Description QTY
A Left Armrest / Leg 1
B Right Armrest / Leg 1
C Seat 1
D Seat Back 1
Caution: You must read this before you proceed
Single Chair
Label Picture Description QTY
E Allen Key 1
F
Bolt
(
M6*30mm
)
5
G
Bolt
(M6*40mm)
3
H
Bolt
(M6*60mm)
3
I Washer 13
J Seat Cushion 1
K
Bolt
(
M6*20mm
)
2
L Connection 1
M Connection 1
Before Beginning Assembly:
Step 1
Step 2
Open the carton and place all the parts on a clean, non-marring surface.
ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting
positions preventing easy assembly.
The PE wicker should never be cut, but moved away from the mounting positions.
Attach Left Armrest / Leg(A) to the Seat(C) using Bolt(F) and Washer(I) with Allen Key(E)
as shown in the picture above.
Loosely tighten the Bolts.
Attach Seat Back(D) to Seat(C) using Washer(I) , Bolt(G&K) &Connection(L&M) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 4
Connect the Chair Legs(A&B) with the Seat Back(D) using Washer(I) and Bolt(H) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 3
Attach Right Armrest / Leg(B) to Seat(C) using Bolt(F) and Washer(I) with Allen Key(E ) as
shown in the picture above.
Loosely tighten the Bolts.
Place the Seat Cushion(J) on the Chair.
Your Chair is ready for use.
Step 5
Check for stability and then tighten all Bolts at all joints.
Note: DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather; in a sequential manner, gradually tighten each Bolt until all Bolts are evenly
secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Step 6
NO. Picture QTY
A 1
B 2
C 1
Assembly instructions
Caution : You must read this before you proceed
TABLE
CAUTION: This table is NOT a TOY.
Keep your child / children at bay in the process of assembly.
Parts list
Leg Support
Description
Table Top
Leg with pre-attached Levellers
Noble House Home Furnishings LLC
1 OF 5
①
19
②
19
③
1
Washer(8mm)
Assembly Preparation
Before Beginning Assembly:
Hardware
Bolt(M8*16)
Allen Wrench(8mm)
Assembly Step
This Table has multiple parts and may require up to some 30 minutes to
assemble.
To give you an overview of the Table parts, the above picture is to help you
put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the
parts and steps before assembly.
Table Top(A)
FRONT FACING
Leg with pre-
attached Leveller(B)
Leg Support (C)
Noble House Home Furnishings LLC
2 OF 5
Unpack and place all parts onto a clean soft surface.
Attach Leg with pre-attached Levellers(B) and Leg Support(C) with Bolts(①)
and Washers(②) by Allen Wrench(③).
DO NOT OVERTIGHTEN.
③
②
①
C
B
Noble House Home Furnishings LLC
3 OF 5
Turn the table top upside down to a soft surface to avoid scratching.
Attach Table Leg with Pre-attached Levellers(B) to the mounting position on
the table top(A) with Bolts(①), Washers(②) by Allen Wrench(③).
DO NOT OVERTIGHTEN.
Turn the Table rightside up.
Adjust the pre-installed Leveller until the Table is level with the ground.
Then, proceed to tighten all Bolts and Nuts.
Your table is ready for use.
Caution: This Table can only be used on a flat, level surface.
Adjust height
for balance
Adjust low
for balance
Noble House Home Furnishings LLC
4 OF 5
Noble House Home Furnishings LLC
5 OF 5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Noble House 22743 Operating instructions

Brand
Noble House
Model
22743
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents