7
Wrench
Screwdriver
M8 NutA
M8 Spring washer B
M8 Flat washer CM8 protect hatsD
Stud M8E
Part
No. Qty Part
No. Description Parts
Picture Qty.
⑤
⑥
L
4
Wrench
Screwdriver
Table Top
Table Leg
Leg Support
12
12
12
12
4
M8 Nut
M8 Spring
washer
M8 Flat
washer
M8
protect
hats
Stud M8
1
1
A
B
C
D
E
①
②
③
④
1
4
1
Rubber Leg
Pad
Note:Rubber Leg Pad L have been
presaaembled
Description Part
picture
PARTS LIST
D
H
Adjust the pre-installed rubber pad (L) until
the chair is level with the ground. Upon
completion of full assembly and bolted up-
all screws can be tightened down.Tighten all
the nuts and cover them with nut caps(I,J).
Attach the backrest (①) to the chair
seat (②) using washers and nuts
(A,B,C).Tighten the nuts using the
wrench . DO NOT over tighten.
Attach the right and left arm(⑤,⑥) using
the bolts (D) and washers,nuts (E,F,G)
.DO NOT over tighten and then using bolts
(H) and washers and nuts (E,F,G).Adjust
to a correct place ,then tighten bolts(D,H).
Step 3
Step 4
Step 5
Step 1
Place all parts on a clean and soft surface
Step 2
Turn over the table top.Attach the stud M8(E) into the
nuts(inside table).
Attach table legs(②) to the studs on the table top (①)
using washers and nuts (A,B,C).DO NOT over tighten
Step 3
Attach the table legs support (③)to the four legs (②)
using flat washer,spring washer and nuts(A,B,C)
DO NOT over tighten.
Step 4
Tighten all nuts with wrench and turn over the table.
Adjust the pre-installed rubber pad (L) until the table
is level with the ground .Tighten all the nuts and cover
them with nut caps(D).Your table can use now.
ASSEMBLY INSTRUCTIONS
A
B
C
A
B
C
A
B
C
ASSEMBLY INSTRUCTIONS
INSTRUCTIONS
Step 1
Step 2
Attach the front and back legs (③,④) to the studs on the
chair seat (②) using washers and nuts (A,B,C).Tighten the
nuts using the wrench & tighten.
Place all parts on a clean and soft surface
Part
No. Description Qty Part
No. Description Parts Picture Qty.
①Backrest 1 A M8 Flat washer
A
M8 Flat washer
10
②Chair Seat 1 B M8 Spring
washer
B
M8 Spring washer
10
③Front Chair
Legs 2 C M8 Nuts
C
M8 Nuts
10
④Back Chair Legs 2 D M6*30 Bolt
D
M6*30 Bolt
2
⑤Left arm 1 E M6 Flat washer
E
M6 Flat washer
6
⑥Right arm 1 F M6 Spring
washer
F
M6 Spring washer
6
⑦Wrench
Wrench
1 G M6 Nuts
G
M6 Nuts
6
⑧Screwdriver
Screwdriver
1 H M6*25 Bolt
H
M6*25 Bolt
4
JM8 protect hats
J
M8 protect hats
10 I M6 protect hats
I
M6 protect hats
6
LRubber Leg Pad 4Note:Rubber Leg Pad L have been
presaaembled
Part picture
*2pcs chair in 1 component bag is avaliable
/
