Noble House 305271 Operating instructions

Brand: Noble House

Model: 305271

Type: Operating instructions

This manual is also suitable for

42659
42961

Label Picture Description QTY

A Left Armrest / Leg 1

B Right Armrest / Leg 1

C Seat 1

D Seat Back 1

Caution: You must read this before you proceed

Single Chair

Label Picture Description QTY

E Allen Key 1

F

Bolt

(

M6*30mm

)

5

G

Bolt

(M6*40mm)

3

H

Bolt

(M6*60mm)

3

I Washer 13

J Seat Cushion 1

K

Bolt

(

M6*20mm

)

2

L Connection 1

M Connection 1

Before Beginning Assembly:

Step 1

Step 2

Open the carton and place all the parts on a clean, non-marring surface.

ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting

positions preventing easy assembly.

The PE wicker should never be cut, but moved away from the mounting positions.

Attach Left Armrest / Leg(A) to the Seat(C) using Bolt(F) and Washer(I) with Allen Key(E)

as shown in the picture above.

Loosely tighten the Bolts.

Attach Seat Back(D) to Seat(C) using Washer(I) , Bolt(G&K) &Connection(L&M) with

Allen Key(E) as pictured above.

Loosely tighten the Bolts.

Step 4

Connect the Chair Legs(A&B) with the Seat Back(D) using Washer(I) and Bolt(H) with

Allen Key(E) as pictured above.

Loosely tighten the Bolts.

Step 3

Attach Right Armrest / Leg(B) to Seat(C) using Bolt(F) and Washer(I) with Allen Key(E ) as

shown in the picture above.

Loosely tighten the Bolts.

Place the Seat Cushion(J) on the Chair.

Your Chair is ready for use.

Step 5

Check for stability and then tighten all Bolts at all joints.

Note: DO NOT fully tighten a Bolt in one go and then move on to the next.

Rather; in a sequential manner, gradually tighten each Bolt until all Bolts are evenly

secured.

This methodology will ensure maximum evenness once all Bolts are fully tightened.

Step 6

Label Picture Description QTY

Parts List

Assembly Instructions

Caution: You must read this before you proceed

Table

Caution: This Table is NOT a TOY

Keep your child/ children at bay during the assembly process.

Whenever moving/lifting the Table and to prevent damage to the Table, two

adults are needed to execute these actions.

A Table Top 1

B Leg 4

C Leg Support 4

Label Picture Description QTY

①

Bolt

(M6x50mm)

9

②

Screw

(M6x35mm)

9

③

Washer

9

④

Allen Key

1

Hardware

Before Beginning Assembly:

Assembly Preparation

Noble House Home Furnishings LLC

Assembly Steps

Noble House Home Furnishings LLC

This Table has multiple parts and may require up to 30 minutes to assemble. To give you

an overview of the Table parts, the above picture is to help you put the various parts into

perspective. Please read through the instructions below to familiarise yourself with the

parts and steps before assembly.

Step 1

Unpack and place all parts on a clean, non-marring surface.

Overview

Leg (B)

FRONT FACING

Leg Support (C)

Table Top (A)

Noble House Home Furnishings LLC

Place Leg Supports(C) between Table Top(A) and Leg(B), as shown above.

3.1) Attach Leg Supports(C) to Table Top(A) using Screws(②) with Allen Key(④).

3.2) Attach Leg Supports(C) to Legs(B) using Screws(②) with Allen Key(④).

Do not fully tighten Screws.

Step 2

Attach Leg(B) to the Table Top(A) using Bolts(①), and Washers(③) with Allen Key(④).

Do not fully tighten the Bolts.

Repeat the same process with the remaining three Legs(B).

Step 3

A

B

4

C

4

2

A

B

3.2

3.1

4

2

3

1

Noble House Home Furnishings LLC

Your Table is ready for use.

This Table can only be used on a flat, level surface.

Step 4

Step 5

Stand the Table up, with assistance from your adult partner.

Exert pressure floorwards, onto the Table with both your hands.

This pressure will help the Legs and Table Top reach full alignment status.

Check for wobbles on a LEVEL surface.

If no wobbles are found proceed to tighten the Bolts and Screws in a sequential manner,

until evenly secured.

When tightening the Bolts and Screws tighten sequentially.

Do not tighten any Bolt or Screw fully and then move on towards the next one.

If there are still wobbles, loosen the Bolts and Screws and excute the same above

process.

If the Table is not Stable it could lead to damage to the product.

Noble House Home Furnishings LLC

Noble House Home Furnishings LLC

Noble House Home Furnishings LLC

Noble House Home Furnishings LLC

Noble House Home Furnishings LLC

Noble House Home Furnishings LLC

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

Noble House 305271 Operating instructions

Brand: Noble House

Model: 305271

Type: Operating instructions

This manual is also suitable for

42659
42961

Download PDF

Related papers

Other documents