Messoa HCR176 User manual

Brand: Messoa

Model: HCR176

Category: Security cameras

Type: User manual

Messoa HCR176 is a high-quality 1080P camera with great features for indoor & outdoor installation. Flexible installation on a ceiling or wall even at an angle to suit your mounting needs. You can adjust lens mode, IRIS speed, shutter, AGC, SENS-UP, brightness, D-WDR, DEFOG, Backlight compensation, White balance, and Day/Night function to have the best viewing experience possible.

AHD 1080P Outdoor Bullet Camera

Quick Start Guide

A.2

Before attempting to connect or operate this product, please read these instructions carefully and save this

manual for future use.

Important Safety Information

FCC Compliance Statement

The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. The limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be

required to correct the interference at their own expense.

FCC Caution:

To ensure continued compliance, use only shielded interface cables when connecting to computer or peripheral

devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operation this equipment.

Warning and Operating Notes

Installation and serving the camera should be performed only by qualified and experienced technicians to conform to all

local codes and to maintain your warranty.

WARNING! The use of CSA certified/ UL Listed Class 2 power adapters are required to ensure

compliance.

WARNING! To reduce the risk of fire or electric shock, do not expose the product to rain or

moisture.

Operating Notes

Power Supply: This AHD 1080P outdoor bullet camera can operate on DC12V / AC24V.

Operating Conditions

 Avoid viewing very bright objects (example, light fixtures) for extended periods.

 Avoid operating or storing the unit in the following locations:

– Extremely humid, dusty, hot, cold environments (where the operating temperature is outside the

recommended range of -4°F to 122°F [-20°C to +50°C].

– Close to sources of powerful radio or TV transmitters

– Close to fluorescent lamps or objects reflecting light

– Under unstable light sources (may cause flickering)

Contents

1. Introduction ........................................................................................................................................................................... 3

1.1 Before You Begin ....................................................................................................................................................... 3

1.2 Unpack Everything .................................................................................................................................................... 3

1.3 Dimensions................................................................................................................................................................. 3

1.4 Names of Camera Parts ........................................................................................................................................... 4

1.5 Routine Maintenance ................................................................................................................................................ 4

2. Installation ............................................................................................................................................................................ 5

3. OSD Settings ....................................................................................................................................................................... 6

3.1 Lens ............................................................................................................................................................................. 6

3.2 Exposure .................................................................................................................................................................... 6

3.3 Backlight ..................................................................................................................................................................... 7

3.4 White BAL................................................................................................................................................................... 7

3.5 Day & Night ................................................................................................................................................................ 7

3.6 NR ................................................................................................................................................................................ 8

3.7 Special ........................................................................................................................................................................ 8

3.8 Adjust .......................................................................................................................................................................... 9

3.9 EXIT ............................................................................................................................................................................ 9

Specifications ........................................................................................................................................................................... 9

1. Introduction

The AHD 1080P outdoor bullet camera is ideal for indoor & outdoor installation. They provide flexible installation on a

ceiling or wall even at an angle.

1.1 Before You Begin

Please read this manual carefully before you install the bullet camera. Keep this manual for future reference.

1.2 Unpack Everything

Check that the items received match those listed on the order form and packing slip. The camera packing box includes:

 One fully assembled camera

 One printed quick guide

 Three pan head screws

 Three screw anchors

 Two torx wrench(one big and one small)

If any parts are missing or damaged, contact the dealer you purchased the camera from.

1.3 Dimensions

Figure 1-1: Physical dimensions

1.4 Names of Camera Parts

Figure 1-2: Camera Connections

1. BNC Video Connector

2. Power Connector (DC12V/AC24V)

3. AHD to CVBS Output Switching Button

1.5 Routine Maintenance

Please use a soft and dry cloth to remove any fingerprint or dust to clean the housing. For more stubborn stains, use a

cloth dampened with a small quantity of neutral detergent to wipe dry.

Caution: Do not use volatile solvents such as alcohol, benzene or thinners to avoid damaging the surface finish.

2. Installation

1. Mark 3 holes at the suitable position and insert the supplied anchors into the holes.

Figure 2-1: Mounting the Bracket

2. Connect the camera power/video cable and external power/video cable together.

Figure 2-2 Cable Connection

3. Adjust the camera to get a suitable position/angle, then tighten the screws with the screws provided and finish the

installation.

3. OSD Settings

The AHD 1080P outdoor bullet camera provides COC function and users are able to control camera menu directly from

AHD DVR by clicking buttons .

3.1 Lens

The DC LENS settings allow you to configure lens mode and IRIS speed. In the DC submenu, you can set the MODE

as OUTDOOR or INDOOR, and adjust IRIS SPEED from 0 to 15. If speed value is less, the IRIS will be become slower.

If speed value is higher, the IRIS will be become more faster. In the OUTDOOR submenu, the Min shutter is 1/30 and

you can adjust the Max shutter from 1/60 to 1/50000.

3.2 Exposure

SHUTTER: 1/30(1/25), 1/60(1/50), FLK, 1/240(1/200), 1/480(1/400), 1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,

x15, x20, x25 and x30, Auto are selectable (Unavailable when DC lens mode is outdoor).

AGC: You can set the AGC value from 0 to 15.

SENS-UP: You can set the SENS-UP as OFF or AUTO. In the AUTO submenu, you can set SENS-UP as

x2/x4/x6/x8/x10/x15/x20/x25/x30.

BRIGHTNESS: You can set the brightness value from 1 to 100.

DC LENS MODE

1. MODE OUTDOOR

2. IRIS SPEED ---I---- 8

3. RETURN RET

EXPOSURE

1. SHUTTER 1/30

2. AGC -------I15

3. SENS-UP OFF

4. BRIGHTNESS ---I---- 40

5. D-WDR ON

6. DEFOG OFF

7. RETURN RET

D-WDR: You can set the D-WDR as OFF, ON or AUTO. If ON is selected, you can adjust the level from 0 to 8.

DEFOG: You can set the DEFOG as OFF or AUTO. In the AUTO submenu, position, size, and the defog gradation (0

to 2) are configurable.

3.3 Backlight

Set Backlight compensation function. It controls the light level to overcome sever backlight conditions. Available

options include OFF, BLC or HSBLC mode. The default is OFF.

 BLC (Backlight Compensation):

– LEVEL: Set the gain of BLC as High, Middle, or Low.

– AREA: Press the up/down/left/right button to define the BLC position and size. Select RET or AGAIN to go

back the BLC menu or re-define the BLC area.

– Default: Restore the BLC settings to the default.

 HSBLC: Select an HSBLC area. Set the DISPLAY status as ON and press the up/down/left/right button to define

the area position and size. Set the BLACK MASK status as ON or OFF. Set the HSBLC LEVEL from 0 to 100.

Select ALL DAY or Night for the HSBLC mode. If Night is selected, you can adjust AGC Level from 0 to 255.

3.4 White BAL

WHITE BALANCE controls color on the screen. Options include ATW (Auto White Balance), AWC→SET, INDOOR,

OUTDOOR, MANUAL or AWB mode. If MANUAL is selected, you can adjust BLUE and RED value from 0 to 100.

3.5 Day & Night

DAY/NIGHT function allows you to set how the camera switches between color and black and white (B/W) mode.

Options include EXT, AUTO, COLOR and B/W.

 EXT: In the EXT submenu, you can set D→N / N→D DELAY within the range 0 to 60.

 AUTO: In the AUTO submenu, you can set:

– D→N (AGC): Set the light level at which the camera switches to NIGHT mode. The higher the value, the

darker the lighting must be there before the camera switches. The value of D→N (AGC) is from 0 to 255.

– D→N/ N→D (DELAY): The Delay has a range from 0 to 60

– N→D (AGC): Set the light level at which the camera switches to DAY mode. The lower the value, the brighter

the lighting must be there before the camera switches. The value of N→G (AGC) is from 0 to 255.

 COLOR: Force the camera to stay in DAY (COLOR) mode at all times.

 B/W: Force the camera to stay in B/W (NIGHT) mode at all times. The B/W submenu allows you to set BURST

and IR SMART to be ON or OFF. If IR SMART is set as ON, you can adjust the level from 0 to 15 and press the

up/down/left/right button to define the position and size of the area.

BLC

1. LEVEL MIDDLE

2. AREA

3. DEFAULT

4. RETURN RET

HSBLC

1. SELECT AREA1

2. DISPLAY ON

3. BLACK MASK ON

4. LEVEL --I----- 20

5. MODE NIHGT

6. DEFAULT

7. RETURN RET

MANUAL WB

1. BLUE ----I---- 50

2. RED ----I---- 50

3. RETURN RET

3.6 NR

NR allows you to configure the DNR (Digital Noise Reduction) settings to reduce noise on the screen. You can set 2D

NR/ 3D NR status as OFF, HIGH, MIDDLE or LOW depending on your environment condition.

3.7 Special

CAM Title: It allows you to specify camera ID. Options are OFF and ON. In the ON submenu, you can add a camera

title up to 15 characters and also select where the title appears on the monitor screen.

D-effect:

– FREEZE: Set the freeze function as ON or OFF.

– MIRROR: OFF, MIRROR, V-FLIP, and ROTATE are selectable for mirror to reflect the image.

– NEG.IMAGE: Set the NEG. IMAGE as ON or OFF.

Motion: MOTION allows camera to detect moving objects on the screen. You can set up to 4 motion areas to detect

moving objectives. Set the DISPLAY status as ON or OFF. In the ON submenu, you can press the up/down/left/right

button to define the position and size of the area. Adjust the motion detection SENSITIVITY from 0 to 100. Set the

COLOR as GREEN, BLUE, WHITE or RED for the motion areas, and the transparent can be select as 1.00, 0.75, 0.25,

or 0.00. In the ALARM submenu, you can do detail settings, such as VIDEO TYPE, OSD VIEW, ALARM OUT. and

TIME.

Privacy: PRIVACY function mask up to 8 privacy areas on the screen from video monitoring. Select a PRIVACY area.

D&N EXT

1. D

→

N (DELAY) I-------- 3

2. N

→

D (DELAY) I-------- 3

3. RETURN RET

D&N AUTO

1. D

→

N (AGC) ------I--200

2. D

→

N (DELAY) I-------- 3

3. N

→

D (AGC) ---I----- 80

4. N

→

D (DELAY) I-------- 3

5. RETURN RET

B/W

1. BURST OFF

2. IR SMART OFF

3. RETURN RET

1. 2DNR LOW

2. 3DNR LOW

3. RETURN RET

SPECIAL

1. CAM TITLE ON

2. D-EFFECT

3. MOTION OFF

4. PRAVICY OFF

5. LANGUAGE ENG

6. DEFECT

7. RS485

8. RETURN RET

MOTION

1. SELECT AREA1

2. DISPLAY ON

3. SENSITIVITY -----I---- 64

4. COLOR GREEN

5. TRANS 1.00

6. ALARM

7. DEFAULT

8. RETURN RET

ALARM

1. VIEW TYPE ALL

2. OSD VIEW ON

3. ALARM OUT ON

4. TIME --I------ 3

5. RETURN RET

Set the DISPLAY status as INV, MOSAIC, COLOR, or OFF, and press the up/down/left/right button to define the

position and size of the area. Set color and transparency for the privacy areas.

Language: OSD support multiple languages. Options include ENG, CHN1, CHN2, GER, FRA, ITA, SPA, POL, RUS,

POR, NED, TUR, KOR, JPN, HEB and ARB.

Defect: LIVE, WHITE and BLACK DPC are adjustable in this section.

RS485: Set CAM ID from 0 to 255, Set the ID DISPLAY as ON or OFF. Set BAUDRATE as

2400/4800/9600/19200/38400.

3.8 Adjust

Picture Adjust allows you to adjust picture settings for optimal image, you can adjust picture Sharpness, Monitor, LSC

and Video.out.

Sharpness: Options are OFF and Auto. In the Auto submenu, you can adjust the sharpness LEVEL from 0 to 15,

START AGC and END AGC from 0 to 255.

Monitor: CRT and LCD are selectable. Select a monitor and enter the submenu to do detail settings, such as GAMMA,

BLUE/RED GAIN.

LSC: Set the LSC status as ON or OFF.

Video. out: PAL or NTSC is selectable.

3.9 EXIT

Press the joystick control to select SAVE&END, RESE or NOT SAVE to exit the menu.

SAVE&END: Save all settings and exit the OSD menu.

RESET: Reset all the settings to the default.

NOT SAVE: Do not save all settings.

Specifications

Model

AHD 1080P outdoor bullet

Image System

Image Device

1/2.8" progressive scan CMOS

Signal System

NTSC/ PAL

Pixel Elements (H x V)

1920 x 1080

Electric

Sync System

Internal

Built-in Lens

f=2.8~12mm, F1.4 DC iris varifocal

View Angle

Horizontal: 100°(wide) ~ 32°(tele), Vertical: 72°(wide) ~ 24°(tele)

Minimum Illumination

0.02 lux (color), 0 lux (IR on)

S/N Ratio

More than 50dB (AGC off)

Gain Control

0~15 level

ADJUST

1. SHARPNESS AUTO

2. MONITOR LCD

3. LSC ON

4. VIDEO.OUT NTSC

5. RETURN RET

White Balance

ATW / AWB / Manual / Outdoor / Indoor / AWC

Electric Shutter

1/30~1/50000 sec (NTSC); 1/25~1/50000 sec (PAL)

Flickerless

Yes

BLC

Off / BLC / HSBLC (Selectable)

Day & Night

Mechanical ICR for day & night function

DNR

2DNR ; 3DNR

Motion Detection

Yes, 4 areas (max)

Privacy Mask

Yes, 8 zones (max)

Defog

Yes

WDR

On / Off (Selectable)

Digital Zoom

Up to x62

Defect Pixel Correction

Yes

OSD

Yes

Multi Language

English, Japanese, German, French, Russian, Portuguese, Spanish,

CHN1, CHN2, Korean, Italian, Polish, Dutch, Turkish, Hebrew and Arabic

Video Frame Rate

1080p @ 30fps (NTSC); 1080p @ 25fps (PAL)

Video Output

HD Analog output / 1Vpp composite output by push button switch

IR Distance

40m (131ft)

IR LED

40pcs

IR Wavelength

850nm

IR Turn on Status

Under 2 lux by photocell auto controlled

LED Life

More than 10,000 hours (50ºC)

Power Supply

Power Requirement

DC 12V & AC 24V ± 10%

Power Consumption

8W max

Environment

Operating Temperature

-20°C~50°C (-4ºF~122ºF)

Operating Humidity

90% max

Storage Temperature

-20°C~60°C (-4°F~140°F)

Storage Humidity

70% max

Mechanism

3 Axis

Yes

Dimension

78.5 x 120.2 x 265.4 mm (3.1" x 4.29" x 10.45”)

Weight

1050g (2.31 lb) approx.

Protection Class

IP66

Ordering Information

HCR176-N5-MES

HCR176-P5-MES

Note: Product specifications are subject to change without prior notice.

Messoa HCR176 User manual

Brand: Messoa

Model: HCR176

Category: Security cameras

Type: User manual

Download PDF

report

Messoa HCR176 User manual

Messoa HCR176 User manual

Related papers

Other documents