AHD 1080P Mini Eyeball / Bullet Camera
Quick Start Guide
A.2
Before attempting to connect or operate this product, please read these instructions carefully and save this
manual for future use.
1
Important Safety Information
FCC Compliance Statement
The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. The limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be
required to correct the interference at their own expense.
FCC Caution:
To ensure continued compliance, use only shielded interface cables when connecting to computer or peripheral
devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operation this equipment.
Warning and Operating Notes
Installation and serving the camera should be performed only by qualified and experienced technicians to conform to all
local codes and to maintain your warranty.
WARNING! The use of CSA certified/ UL Listed Class 2 power adapters are required to ensure
compliance.
WARNING! To reduce the risk of fire or electric shock, do not expose the product to rain or
moisture.
Operating Notes
Power Supply: This mini eyeball / mini bullet camera can operate on DC 12V.
Operating Conditions
Avoid viewing very bright objects (example, light fixtures) for extended periods.
Avoid operating or storing the unit in the following locations:
– Extremely humid, dusty, hot, cold environments (where the operating temperature is outside the
recommended range of -14°F to 122°F [-10°C to +50°C ].
– Close to sources of powerful radio or TV transmitters
– Close to fluorescent lamps or objects reflecting light
– Under unstable light sources (may cause flickering)
2
1. Introduction
The mini eyeball and mini bullet cameras are ideal for indoor & outdoor installation. They provide flexible installation on
a ceiling or wall even at an angle.
1.1 Before You Begin
Please read this manual carefully before you install the dome camera. Keep this manual for future reference.
1.2 Unpack Everything
Check that the items received match those listed on the order form and packing slip. The camera packing box includes:
HED110 AHD 1080P Mini Eyeball:
One fully assembled camera
Four pan head screws
Four screw anchors
One torx wrench
HCR170 AHD 1080P Mini Bullet:
One fully assembled camera
Three pan head screws
Three screw anchors
One torx wrench
One buffer foam of bracket
If any parts are missing or damaged, contact the dealer you purchased the camera from.
1.3 Dimensions
AHD 1080P Mini Eyeball Camera
3
AHD 1080P Mini Bullet Camera
Figure 1-1: Physical dimensions
1.4 Names of Camera Parts
AHD 1080P Mini Eyeball Camera
AHD 1080P Mini Bullet Camera
Figure 1-2: Camera Connections
1. BNC Video Connector
2. Power Connector (DC 12V)
3. AHD to CVBS Output Switching Button
1.5 Routine Maintenance
Please use a soft and dry cloth to remove any fingerprint or dust to clean the housing. For more stubborn stains, use a
cloth dampened with a small quantity of neutral detergent to wipe dry.
Caution: Do not use volatile solvents such as alcohol, benzene or thinners to avoid damaging the surface finish.
4
2. Installation
2.1 For AHD 1080P Mini Eyeball Camera
1. Loosen the screw with torx wrench (supplied) to remove the camera body from the bottom case.
Figure 2-1 Disassembling the bottom case
2. Mark 4 holes at the suitable position and fasten the bottom case on the ceiling with the screws provided.
Figure 2-2 Mounting the bottom case
3. Connect the camera power/video cable and external power/video cable together.
4. Put the camera body into the bottom case and adjust the camera to get a suitable position and angle. Then fasten
the camera by screwing camera body to the bottom case with screws.
Figure 2-3: Assembling the camera
Screw Anchors
Pan Head Screws
Torx Wrench
5
2.2 For AHD 1080P Mini Bullet Camera
1. Mark 3 holes at the suitable position and Insert the supplied anchors into the holes.
Figure 2-4: Mounting the Bracket
2. Connect the camera power/video cable and external power/video cable together.
Figure 2-5 Cable Connection
3. Adjust the camera to get a suitable position/angle, then tighten the screws with the screws provided and finish the
installation.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
