Messoa HED110 User manual

Brand: Messoa

Model: HED110

Category: Security cameras

Type: User manual

This manual is also suitable for

HCR170

AHD 1080P Mini Eyeball / Bullet Camera

User Manual

A.2

Before attempting to connect or operate this product, please read these instructions carefully and save this

manual for future use.

Important Safety Information

FCC Compliance Statement

The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. The limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be

required to correct the interference at their own expense.

FCC Caution:

To ensure continued compliance, use only shielded interface cables when connecting to computer or peripheral

devices. Any changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operation this equipment.

Warning and Operating Notes

Installation and serving the camera should be performed only by qualified and experienced technicians to conform to all

local codes and to maintain your warranty.

WARNING! The use of CSA certified/ UL Listed Class 2 power adapters are required to ensure

compliance.

WARNING! To reduce the risk of fire or electric shock, do not expose the product to rain or

moisture.

Operating Notes

Power Supply: This mini eyeball / mini bullet camera can operate on DC 12V.

Operating Conditions

 Avoid viewing very bright objects (example, light fixtures) for extended periods.

 Avoid operating or storing the unit in the following locations:

– Extremely humid, dusty, hot, cold environments (where the operating temperature is outside the

recommended range of -14°F to 122°F [-10°C to +50°C ].

– Close to sources of powerful radio or TV transmitters

– Close to fluorescent lamps or objects reflecting light

– Under unstable light sources (may cause flickering)

Contents

1. Introduction....................................................................................................................................................... 3

1.1 Before You Begin .................................................................................................................................... 3

1.2 Unpack Everything ................................................................................................................................. 3

1.3 Dimensions ............................................................................................................................................. 3

1.4 Names of Camera Parts ......................................................................................................................... 4

1.5 Routine Maintenance .............................................................................................................................. 4

2. Installation ........................................................................................................................................................ 5

2.1 For AHD 1080P Mini Eyeball Camera .................................................................................................... 5

2.2 For AHD 1080P Mini Bullet Camera ....................................................................................................... 6

3. OSD Settings ................................................................................................................................................... 7

3.1 Lens ........................................................................................................................................................ 7

3.2 Exposure................................................................................................................................................. 7

3.3 Backlight ................................................................................................................................................. 8

3.4 White BAL ............................................................................................................................................... 8

3.5 Day & Night ............................................................................................................................................ 8

3.6 NR ........................................................................................................................................................... 9

3.7 Special .................................................................................................................................................... 9

3.8 Adjust .................................................................................................................................................... 10

3.9 EXIT ...................................................................................................................................................... 10

Specifications ..................................................................................................................................................... 10

1. Introduction

The mini eyeball and mini bullet cameras are ideal for indoor & outdoor installation. They provide flexible installation on

a ceiling or wall even at an angle.

1.1 Before You Begin

Please read this manual carefully before you install the dome camera. Keep this manual for future reference.

1.2 Unpack Everything

Check that the items received match those listed on the order form and packing slip. The camera packing box includes:

HED110 AHD 1080P Mini Eyeball:

 One fully assembled camera

 Four pan head screws

 Four screw anchors

 One torx wrench

HCR170 AHD 1080P Mini Bullet:

 One fully assembled camera

 Three pan head screws

 Three screw anchors

 One torx wrench

 One buffer foam of bracket

If any parts are missing or damaged, contact the dealer you purchased the camera from.

1.3 Dimensions

AHD 1080P Mini Eyeball Camera

AHD 1080P Mini Bullet Camera

Figure 1-1: Physical dimensions

1.4 Names of Camera Parts

AHD 1080P Mini Eyeball Camera

AHD 1080P Mini Bullet Camera

Figure 1-2: Camera Connections

1. BNC Video Connector

2. Power Connector (DC 12V)

3. AHD to CVBS Output Switching Button

1.5 Routine Maintenance

Please use a soft and dry cloth to remove any fingerprint or dust to clean the housing. For more stubborn stains, use a

cloth dampened with a small quantity of neutral detergent to wipe dry.

Caution: Do not use volatile solvents such as alcohol, benzene or thinners to avoid damaging the surface finish.

2. Installation

2.1 For AHD 1080P Mini Eyeball Camera

1. Loosen the screw with torx wrench (supplied) to remove the camera body from the bottom case.

Figure 2-1 Disassembling the bottom case

2. Mark 4 holes at the suitable position and fasten the bottom case on the ceiling with the screws provided.

Figure 2-2 Mounting the bottom case

3. Connect the camera power/video cable and external power/video cable together.

4. Put the camera body into the bottom case and adjust the camera to get a suitable position and angle. Then fasten

the camera by screwing camera body to the bottom case with screws.

Figure 2-3: Assembling the camera

Screw Anchors

Pan Head Screws

Torx Wrench

2.2 For AHD 1080P Mini Bullet Camera

1. Mark 3 holes at the suitable position and Insert the supplied anchors into the holes.

Figure 2-4: Mounting the Bracket

2. Connect the camera power/video cable and external power/video cable together.

Figure 2-5 Cable Connection

3. Adjust the camera to get a suitable position/angle, then tighten the screws with the screws provided and finish the

installation.

3. OSD Settings

The AHD 1080P Mini Eyeball and Mini Bullet cameras provide COC function and users are able to control camera

menu directly from AHD DVR by clicking buttons.

3.1 Lens

The LENS settings allow you to configure Lens and speed. Options are Manual and DC. The default setting is Manual.

In the DC submenu, you can set the MODE as INDOOR or OUTDOOR, and adjust IRIS SPEED from 0 to 15.

If speed value is less, the IRIS will be become slower. If speed value is higher, the IRIS will be become more faster. If

OUTDOOR mode is selected, the Min shutter is 1/30 and you can adjust the Max shutter from 1/60 to 1/50000.

3.2 Exposure

SHUTTER: 1/30(1/25), 1/60(1/50), FLK, 1/240(1/200), 1/480(1/400), 1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,

x15, x20, x25 and x30, Auto are selectable.

AGC: You can set the AGC value from 0 to 15.

SENS-UP: You can set the SENS-UP as OFF or AUTO. In the AUTO submenu, you can set SENS-UP as

x2/x4/x6/x8/x10/x15/x20/x25/x30.

BRIGHTNESS: You can set the brightness value from 1 to 100.

EXPOSURE

1. SHUTTER 1/30

2. AGC ------I-13

3. SENS-UP OFF

4. BRIGHTNESS ---I---- 45

5. D-WDR ON

6. DEFOG OFF

7. RETURN RET

DC LENS MODE

1. MODE INDOOR

2. IRIS SPEED ---I---- 8

3. RETURN RET

D-WDR: You can set the D-WDR as OFF, ON or AUTO. If ON is selected, you can adjust the level from 0~8.

DEFOG: You can set the DEFOG as OFF or AUTO. In the AUTO submenu, position, size, and the defog gradation (0

to 2) are configurable.

3.3 Backlight

Set Backlight compensation function. It controls the light level to overcome sever backlight conditions. Available

options include OFF, BLC or HSBLC mode. The default is OFF.

 BLC (Backlight Compensation):

– LEVEL: Set the gain of BLC as High, Middle, or Low.

– AREA: Press the up/down/left/right button to define the BLC position and size. Select RET or AGAIN to go

back the BLC menu or re-define the BLC area.

– Default: Restore the BLC settings to the default.

 HSBLC: Select an HSBLC area. Set the DISPLAY status as ON and press the up/down/left/right button to define

the area position and size. Set the BLACK MASK status as ON or OFF. Set the HSBLC LEVEL from 0 to 100.

Select ALL DAY or Night for the HSBLC mode.

3.4 White BAL

WHITE BALANCE controls color on the screen. Options include ATW (Auto White Balance), AWC→SET, INDOOR,

OUTDOOR, MANUAL or AWB mode. If MANUAL is selected, you can adjust BLUE and RED value from 0 to 100.

3.5 Day & Night

DAY/NIGHT function allows you to set how the camera switches between color and black and white (B/W) mode.

Options include EXT, AUTO, COLOR and B/W.

 EXT: In the EXT submenu, you can set D→N / N→D DELAY within the range 0 to 60.

 AUTO: In the AUTO submenu, you can set:

– D→N (AGC): Set the light level at which the camera switches to NIGHT mode. The higher the value, the

darker the lighting must be there before the camera switches. The value of D→N (AGC) is from 0 to 255.

– D→N/ N→D (DELAY): The Delay has a range from 0 to 60

– N→D (AGC): Set the light level at which the camera switches to DAY mode. The lower the value, the brighter

the lighting must be there before the camera switches. The value of N→G (AGC) is from 0 to 255.

 COLOR: Force the camera to stay in DAY (COLOR) mode at all times.

 B/W: Force the camera to stay in B/W (NIGHT) mode at all times. The B/W submenu allows you to set BURST

and IR SMART to be ON or OFF. If IR SMART is set as ON, you can adjust the level from 0 to 15 and press the

up/down/left/right button to define the position and size of the area.

MANUAL WB

1. BLUE ----I---- 50

2. RED ----I---- 50

3. RETURN RET

HSBLC

1. SELECT AREA1

2. DISPLAY ON

3. BLACK MASK ON

4. LEVEL --I----- 20

5. MODE ALL DAY

6. DEFAULT

7. RETURN RET

BLC

1. LEVEL MIDDLE

2. AREA

3. DEFAULT

4. RETURN RET

3.6 NR

NR allows you to configure the DNR (Digital Noise Reduction) settings to reduce noise on the screen. You can set 2D

NR/ 3D NR status as OFF, HIGH, MIDDLE or LOW depending on your environment condition.

3.7 Special

CAM Title: It allows you to specify camera ID. Options are OFF and ON. In the ON submenu, you can add a camera

title up to 26 characters with 2 lines and also select where the title appears on the monitor screen.

D-effect:

– FREEZE: Set the freeze function as ON or OFF.

– MIRROR: OFF, MIRROR, V-FLIP, and ROTATE are selectable for mirror to reflect the image.

– NEG.IMAGE: Set the NEG. IMAGE as ON or OFF.

Motion: MOTION allows camera to detect moving objects on the screen. You can set up to 4 motion areas to detect

moving objectives. Set the DISPLAY status as ON or OFF. In the ON submenu, you can press the up/down/left/right

button to define the position and size of the area. Adjust the motion detection SENSITIVITY from 0 to 100. Set the

COLOR as GREEN, BLUE, WHITE or RED for the motion areas, and the transparent can be select as 1.00, 0.75, 0.25,

or 0.00. In the ALARM submenu, you can do detail settings, such as VIDEO TYPE, OSD VIEW, ALARM OUT. and

TIME.

Privacy: PRIVACY function mask up to 8 privacy areas on the screen from video monitoring. Select a PRIVACY area.

Set the DISPLAY status as INV, MOSAIC, COLOR, or OFF, and press the up/down/left/right button to define the

position and size of the area. Set color and transparency for the privacy areas.

MOTION

1. SELECT AREA1

2. DISPLAY ON

3. SENSITIVITY -----I---- 64

4. COLOR GREEN

5. TRANS 1.00

6. ALARM

7. DEFAULT

8. RETURN RET

SPECIAL

1. CAM TITLE OFF

2. D-EFFECT

3. MOTION OFF

4. PRAVICY OFF

5. LANGUAGE ENG

6. DEFECT

7. RS485

8. RETURN RET

1. 2DNR MIDDLE

2. 3DNR MIDDLE

3. RETURN RET

B/W

1. BURST ON

2. IR SMART OFF

3. RETURN RET

D&N AUTO

1. D

→

N (AGC) ------I--200

2. D

→

N (DELAY) I-------- 1

3. N

→

D (AGC) ---I----- 80

4. N

→

D (DELAY) I-------- 1

5. RETURN RET

D&N EXT

1. D

→

N (DELAY) I-------- 2

2. N

→

D (DELAY) I-------- 2

3. RETURN RET

ALARM

1. VIEW TYPE ALL

2. OSD VIEW ON

3. ALARM OUT ON

4. TIME --I------ 3

5. RETURN RET

Language: OSD support multiple languages. Options include ENG, CHN1, CHN2, GER, FRA, ITA, SPA, POL, RUS,

POR, NED and TUR.

Defect: LIVE, WHITE and BLACK DPC are adjustable in this section.

RS485: Set CAM ID from 0 to 255, Set the ID DISPLAY as ON or OFF. Set BAUDRATE as

2400/4800/9600/19200/38400.

3.8 Adjust

Picture Adjust allows you to adjust picture settings for optimal image, you can adjust picture Sharpness, Monitor, LSC

and Video.out.

Sharpness: Options are OFF and Auto. In the Auto submenu, you can adjust the sharpness LEVEL from 0 to 15,

START AGC and END AGC from 0 to 255.

Monitor: CRT and LCD are selectable. Select a monitor and enter the submenu to do detail settings, such as GAMMA,

BLUE/RED GAIN.

LSC: Set the LSC status as ON or OFF.

Video. out: PAL or NTSC is selectable.

3.9 EXIT

Press the joystick control to select SAVE&END, RESE or NOT SAVE to exit the menu.

SAVE&END: Save all settings and exit the OSD menu.

RESET: Reset all the settings to the default.

NOT SAVE: Do not save all settings.

Specifications

Model

AHD 1080P Mini Eyeball AHD 1080P Mini Bullet

Image System

Image Device 1/3" progressive scan CMOS

Signal System NTSC/ PAL

Pixel Elements (H x V) 1920 x 1080

Electric

Sync System Internal

Built-in Lens f=3.6mm, F2.0

View Angle Horizontal: 85°

Minimum Illumination 0.1 lux (color), 0 lux (IR on)

S/N Ratio More than 50dB (AGC off)

Gain Control 0~15 level

White Balance ATW / AWB / Manual / Outdoor / Indoor / AWC

Electric Shutter 1/30~1/50000 sec (NTSC); 1/25~1/50000 sec (PAL)

ADJUST

1. SHARPNESS AUTO

2. MONITOR LCD

3. LSC ON

4. VIDEO.OUT NTSC

5. RETURN RET

Flickerless Yes

BLC Off / BLC / HSBLC (Selectable)

Day & Night Mechanical ICR for day & night function

DNR 2DNR ; 3DNR

Motion Detection Yes, 4 areas (max)

Privacy Mask Yes, 8 zones (max)

Defog Yes

WDR On / Off (Selectable)

Digital Zoom Up to x62

Defect Pixel Correction Yes

OSD Yes

Multi Language

English, German, French, Russian, Portuguese, Spanish, CHN1, CHN2,

Italian, Polish, Dutch, Turkish

Video Frame Rate 1080p @ 30fps (NTSC); 1080p @ 25fps (PAL)

Video Output HD Analog output /CVBS output by switch button

IR Distance 20m (66ft)

IR LED 6 pcs of high power LED

IR Wavelength 850nm

IR Turn on Status Under 5 lux by photocell auto controlled

LED Life More than 10,000 hours (50ºC)

Power Supply

Power Requirement DC12V ± 10%

Power Consumption 4W max

Environment

Operating Temperature -10°C~50°C (-14ºF~122ºF)

Operating Humidity 90% max

Storage Temperature -20°C~60°C (-4°F~140°F)

Storage Humidity 70% max

Mechanism

3 Axis Yes

Dimension 106.5 x 60.84 mm (4.19" x 2.39”) Φ55 x 144.8 mm (2.16" x 5.7”)

Weight 300g (0.66 lb) approx.

Protection Class IP66

Ordering Information

HED110-N1-MES

HED110-P1-MES

HCR170-N1-MES

HCR170-P1-MES

Note: Product specifications are subject to change without prior notice.

Page is loading ...

Messoa HED110 User manual

Brand: Messoa

Model: HED110

Category: Security cameras

Type: User manual

This manual is also suitable for

HCR170

Download PDF

report

in other languages

日本語: Messoa HED110 ユーザーマニュアル

Messoa HED110 User manual

This manual is also suitable for

Messoa HED110 User manual

in other languages

Related papers

Other documents