American Standard 9118.111.020 Installation guide

Brand: American Standard

Model: 9118.111.020

Category: Sanitary ware

Type: Installation guide

7301793-100 Rev. F

Introduction: Thank you for selecting our products...products which have been the

benchmarks of fine quality for years. To help insure that the installation process will

proceed smoothly, please read these instructions carefully before you begin. Also,

review the recommended tools and materials list; carefully unpack and examine your

new plumbing fixture.

Channel Lock Pliers

Regular Screwdriver

Recommended Tools & Materials

Rough-In

Dimensions

Phillips Screwdriver

Pipe Wrench

Drill

Plumbers' Putty or Caulking

Tubing Cutter

Tape

Measure

Hacksaw

Pencil

Torch

Level

SAVE FOR FUTURE USE

NOTE: Pictures may not exactly define contour of china and components.

ICS Sink with Selectronic IC Faucet*

Models: 9118.111, 9118.100 & 9118.150

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.

14-3/4"

(375mm)

17"

(432mm)

4-3/4"

(121mm)

5/8"

(14mm)

1-5/8"

(41mm)

20"

(509mm)

4-3/4"

(120mm)

8" (203mm)

1/2" DIA.

(13mm)

FINISHED WALL

BASE MOUNT

DETAIL

FINISHED

FLOOR

FINISHED

FLOOR

FINISHED

FLOOR

26-1/8"

(663mm)

36"

(914mm)

36-1/2"

(927mm)

36-1/2"

(927mm)

40-1/8"

(1020mm)

2-3/4"

(70mm)

9/16" DIA.

(14mm)

2-3/4"

(70mm)

(102mm)

MOUNTING

STUDS

Adjustable Wrench

*FAUCET PERCH

2-1/2" DIA. (65mm)

*FAUCET PERCH

2-1/2" DIA. (65mm)

*DISCLAIMER: Faucets with a base diameter greater than 2-1/4" (57 mm) will not fit on

this ICS Sink. The Selectronic IC Faucet was specifically designed to minimize splashing

during operation. American Standard will not be liable for any splashing that occurs if

faucets other than the American Standard IC Faucets are used.

This product will not eliminate the risk of infection, but provides a hygienic environment

by reducing splashing through its unique design.

8"(203mm) BETWEEN

MOUNTING HOLES

RECOMMENDED CARRIERS:

JAY R. SMITH MFG. CO.

MODEL SQ-0-4437

FLOOR MOUNTED SINK SUPPORT

WATTS CA-311

FLOOR MOUNTED URINAL CARRIER

CAUTION: PRODUCT IS FRAGILE. TO AVOID DAMAGE AND POSSIBLE INJURY HANDLE WITH CARE!

7301793-100 Rev. F

NOTE: For more detailed information, see the

installation instructions supplied with the

IC FAUCET. # M965119

36-1/2"

(927mm)

18"

(457mm)

SQ-0-4437 FLOOR

MOUNTED SINK

SUPPORT

1-5/8"

(41mm)

FINISHED WALL

MOUNTING

STUDS

8" (203mm)

FINISHED

FLOOR

INSTALL FAUCETROUGH-IN SUPPLIES AND WASTE OUTLET

INSTALL GRID DRAIN AND OFFSET TAILPIECE

1. Insert WIRES (1), FLEX HOSE (2) and SPOUT SHANK (3)

through center hole of mounting surface.

2. Assemble "C" WASHER (4), STAR WASHER (5) and LOCKNUT

(6) onto threads of SPOUT SHANK (3) from underside of

mounting surface.

3. Align FAUCET and tighten LOCKNUT (6).

1. Apply plumber’s putty to the underside of flange. Install GRID DRAIN into drain outlet.

2. From the underside of SINK install RUBBER GASKET (flat side up) and FRICTION

GASKET onto GRID DRAIN threads. Apply sealent to threads of GRID DRAIN.

3. Apply sealent to threads of OFFSET TAILPIECE and thread into DRAIN ELL.

4. Thread DRAIN ELL onto GRID DRAIN, tighten and align as shown.

1. Rough-in 3/8" supplies and waste outlet connections.

3/8" (10mm)

SUPPLIES

(102mm)

*CHECK LOCAL CODES

RUBBER

GASKET

FRICTION

GASKET

APPLY

SEALANT

APPLY SEALANT

TO THREADS

DRAIN ELL

OFFSET TAILPIECE

DRAIN ELL

GRID DRAIN

NOTE: For ease of installation and accessibility, it is

recommended that straight stops with flex

supply tubes be used. As an alternative, if rigid

supply risers are used, it is suggested to use

angle stops in place of the straight stops.

*1-1/4" (32mm)

OR 1-1/2" (38mm)

WASTE OUTLET

PLUMBER’S

PUTTY

GRID DRAIN

7301793-100 Rev. F

INSTALL ICS SINK

1. Mount SINK onto the two HANGER STUDS. Hold SINK in place

and temporarily install NYLOCK NUT & WASHER on one of the

HANGER STUDS to retain SINK.

MOUNT ELECTRONICS BOX

COMPLETE WASTE OUTLET CONNECTION

NOTE: Installation with ELECTRONIC BOX only is for cold

or tempered water. Use optional MIXING VALVE

with ELECTRONIC BOX when Hot and Cold supplies

are roughed-in. See illustration below.

INSTALL ELECTRONICS HANGER BRACKET

1. Install the ELECTRONICS HANGER BRACKET onto remaining

HANGER STUD. Install NYLOCK NUT & WASHER but do not

tighten fully.

2. Remove NYLOCK NUT & WASHER from first HANGER STUD

and install other end of ELECTRONICS HANGER BRACKET.

Replace NYLOCK NUT & WASHER, tighten both ends. Do not

over tighten, chinaware could become damaged.

NYLOCK NUT

AND WASHER

COLD WATER OR

TEMPERED WATER

(3/8" SUPPLY)

HOT

MIXING VALVE

ELECTRONIC

BOX

ELECTRONIC BOX

COLD

1. Connect SUPPLY NUT (1) from SPOUT assembly to nipple on

top of ENCLOSURE (2). Tighten with adjustable wrench to make

a water tight connection.

CONNECT SPOUT HOSE TO ENCLOSURE

1. Install “P” TRAP. Connect OFFSET TAILPIECE to “P” TRAP.

TAILPIECE may have to be cut to fit installation. Use tubing

cutter to cut TAILPIECE.

P-TRAP

TAILPIECE

1-1/4" OD

1-1/4" or 1-1/2" OD

WASTE OUTLET

1. Remove COVER from ELECTRONICS BOX.

2. Place ELECTRONICS BOX onto MOUNTING PLATE. Align

BOX with mounting holes. Attach with SCREWS provided.

3. Hang MOUNTING PLATE with ELECTRICAL BOX on

HANGER BRACKET.

ELECTRONICS

HANGER

BRACKET

HANGER STUD

SCREWS

ELECTRONIC

BOX

MIXING VALVE

MOUNTING PLATE

7301793-100 Rev. F

INSTALL AND CONNECT MIXING VALVE

(MIXING VALVE IS OPTIONAL)

CONNECT MIXING VALVE TO WATER SUPPLIES

ELECTRICAL HOOK-UP AND INSTALLATION

COLD WATER

OR TEMPERED

WALL SUPPLY

ELECTRONIC

BOX

Installation Instructions

(In Toronto Area only: 1-905-3061093)

SELECTRONIC

Proximity IC Faucet

Certiﬁed to comply with ASME A112.18.1M

To learn more about American Standard Faucets visit our website at: www.americanstandard.com

or U.S. customer's e-mail us at: [email protected]

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-306-1093)

M965119

Product No.'s & Options

Speciﬁcations

How to Install

Electrical Hook-up

Maintenance

FAQ, s

Replacement Parts

2-3

4-6

7-8

6055.193

6056.193

MODEL NUMBERS

6055 / 6056 IC Faucet shown Installed on

American Standard 9118.111 ICS Sink

1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on ENCLOSURE (2).

2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to FLEXIBLE SUPPLY

HOSE (3). Tighten to make a water tight connection. Use two

wrenches to tighten if necessary.

3. Connect FLEXIBLE SUPPLY (3) directly to wall supply. Connection on

FLEXIBLE SUPPLY (3) is 3/8" compression. Use adjustable wrench to

tighten connection. Do not over tighten.

Note: FLEXIBLE SUPPLY (3) measures 20" from the bottom of the

ENCLOSURE (1) base. If additional supply length is required,

installer must purchase parts separately.

Important: If FLEXIBLE SUPPLY (3) is too long, loop to avoid kinking.

CONNECT WATER SUPPLY TO ENCLOSURE

AND TO COLD OR TEMPERED WALL SUPPLY

1. Remove COVER from MIXING VALVE.

2. Install FIBER SEAL WASHER (4) on MIXING VALVE

NIPPLE (3). Hold MIXING VALVE (1) in place with one

hand and with your other hand thread SWIVEL NUT (2)

onto MIXING VALVE NIPPLE (3). Use an adjustable

wrench to tighten SWIVEL NUT (2).

3. Place MIXING VALVE BOX onto MOUNTING PLATE. Align

BOX with mounting holes. Attach with SCREWS provided.

4. Replace COVER and tighten securely.

NOTE: For complete detailed installation and operating

instructions see installations instructions supplied

with mixing valve. No. M968808

For complete detailed installation and operating

instructions see installations instructions supplied with

IC FAUCET. No. M965119

ADJUSTABLE

WRENCH

HOT

MIXING VALVE

ELECTRONIC

BOX

COLD

1. Turn off Hot and Cold water supplies before beginning.

2. Connect FLEXIBLE SUPPLIES directly to wall supplies.

Connections on MIXER supplies are 3/8" compression.

Connect left supply to Hot and right supply to Cold wall supply.

Use adjustable wrench to tighten connections.

Do not over tighten.

3. Faucet supplies measure 20" from the bottom of the

ENCLOSURE (3) base.

Note: If additional supply length is required, installer must

purchase parts separately.

Important: If SUPPLY HOSES (1, 2) are too long, loop as

to avoid kinking.

Installation Instructions

(In Toronto Area only: 1-905-3061093)

SELECTRONIC®

Thermostatic Mixing Valve

Certiﬁed to comply with ASME A112.18.1M

M968808

To learn more about American Standard Faucets visit our website at: www.americanstandard.com

or U.S. customer's e-mail us at: [email protected]

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-306-1093)

605XTMV

Specications

Installation

Adjust Temperature

Service

Replacement Parts

No. M968808

No. M965119

7301793-100 Rev. F

WIRE HANGER

EYEBOLT

REMOVE THUMB NUT

FROM EYE BOLT

4. WIRE HANGER is positioned behind ELECTRONIC BOX

and in front of DRAIN.

5. Remove THUMB NUT from EYEBOLT.

CHECK ALL ELECTRICAL AND

PLUMBING CONNECTIONS

TEST INSTALLED FAUCET

INSTALL WIRE HANGER

1. Turn on water supplies and check for leaks.

Tighten any connections if necessary.

2. Check FAUCET operation, if adjustment is

required refer to the installation instructions

shown at right supplied with the IC FAUCET.

No. M965119.

1. Install EYEBOLT onto WIRE HANGER if not installed.

2. Place WIRE end in left SIDE HOLE.

3. Place WIRE end in right SIDE HOLE near DRAIN.

NOTE: If not enough tension, remove WIRE and spread

ends approx. 1" additional and re-attach.

6. EYEBOLT for SINK APRON.

No. M965119

Installation Instructions

(In Toronto Area only: 1-905-3061093)

SELECTRONIC

Proximity IC Faucet

Certiﬁed to comply with ASME A112.18.1M

To learn more about American Standard Faucets visit our website at: www.americanstandard.com

or U.S. customer's e-mail us at: [email protected]

For Parts, Service, Warranty or other Assistance,

please call

1-800-442-1902 (In Canada: 1-800-387-0369)

NOTE TO INSTALLER: Please give this manual to the customer after installation.

(In Toronto Area only: 1-905-306-1093)

M965119

Product No.'s & Options

Speciﬁcations

How to Install

Electrical Hook-up

Maintenance

FAQ,s

Replacement Parts

2-3

4-6

7-8

6055.193

6056.193

MODEL NUMBERS

6055 / 6056 IC Faucet shown Installed on

American Standard 9118.111 ICS Sink

WIRE

WIRE HANGER

EYEBOLT

TO ENSURE A LAMINAR WATER

FLOW the air must be slowly purged

from the spout. To do so, cover the

SENSOR (1) while slowly opening

the water supply valves. When the

water flows as a solid, smooth,

steady stream, uncover the

SENSOR (1) and fully open the

water supply valve.

DETECTION

ZONE

7301793-100 Rev. F

INSTALL SINK APRON

1. Hold APRON up against SINK and flush against finished wall.

2. Mark a line with a pencil on the wall about 6" long as shown on

both sides of the APRON.

3. Remove the APRON. Clean the wall where the APRON

BRACKETS supplied with SINK are to be applied. Peel off the

protective strip from the back of the APRON BRACKETS. Apply

the two APRON BRACKETS to the finished wall parallel to the

pencil marks as shown in the illustration below.

OPTIONAL MOUNTING.

(SCREWS AND ANCHORS NOT SUPPLIED)

Use Brackets to mark pilot holes on wall. Drill holes for ANCHORS.

Peel off the protective strip from the back of the APRON BRACKETS. Apply

the two APRON BRACKETS to the finished wall parallel to the pencil marks

as shown and aligned with the mounting holes. See illustration below. Install

SCREWS and tighten.

4. Clean off the pencil marks from wall.

(152mm)

APRON

SINK

6. Retain APRON with THUMB NUT. Finger tight only.5. Position APRON under SINK and against finished wall alinging

EYEBOLT with hole in APRON.

THUMB NUT

EYEBOLT

APRON

IMPORTANT: SAVE ALL INSTALLATION INSTRUCTIONS FOR FUTURE USE

1/2"

(13mm)

PENCIL MARK

APRON

CLEAN WALL

PROTECTIVE

STRIP

7301793-100 Rev. F

Repair Parts

ICS Sink

Models: 9118.111,

9118.100 & 9118.150

7381259-401.0200A

ICS Sink

Shroud Kit

7381243-251.0020A

Oset Drain

7381242-0500A

P-Trap Assembly

7381266-200.0070A

Bracket Assembly

7381267-400.0070A

Mounting Bracket Kit

7301793-100 Rev. F

THIS WARRANTY IS NOT TRANSFERABLE FROM ORIGINAL CONSUMER PURCHASER.

AS AMERICA, INC. ONE YEAR LIMITED WARRANTY

If inspection of this AS America, Inc. (“American Standard”) plumbing product, within one year after its initial

purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its

option, exchange the product for a similar model.

This limited warranty applies only to the original purchaser and installation of these products. In the event of a

limited warranty claim, proof of purchase will be required—save sales receipt.

This limited warranty does not apply to local building code compliance. Since local building codes vary

considerably, the purchaser of this product should check with a local building or plumbing contractor to insure

local code compliance

before installation.

This limited warranty is void if the product has been moved from its initial place of installation; if it has been

subjected to faulty maintenance, abuse, misuse, accident or other damages; if it was not installed in accordance

with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as

shipped by American Standard.

American Standard's option to repair or exchange the product under this limited warranty does not cover any

labor or other costs of removal or installation. IN NO EVENT WILL AMERICAN STANDARD BE LIABLE FOR

THE COST OF REPAIR OR REPLACEMENT OF ANY INSTALLATION MATERIALS, INCLUDING BUT NOT

LIMITED TO, TILES, MARBLE, ETC. American Standard will not be responsible for any other incidental or

consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of

which are expressly excluded from this limited warranty. This limited warranty does not cover any liability for

consequential or incidental damages, all of which are hereby expressly disclaimed, or the extension beyond the

duration of this limited warranty of any implied limited warranties, including those of merchantability or fitness for

an intended purpose. (Some states or provinces do not allow the exclusion or limitation of implied limited

warranties, so this exclusion may not apply to you.)

This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to

state or from province to province, in which case this limited warranty does not affect such statutory rights.

In the United States:

American Standard Brands

P.O. Box 6820

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 442-1902

www.americanstandard.com

In Canada:

AS Canada, ULC

5900 Avebury Rd.

Mississauga, Ontario

Canada L5R 3M3

Toll Free: (800) 387-0369

www.americanstandard.ca

In Mexico:

American Standard B&K Mexico

S. de R.L. de C.V.

Via Morelos #330

Col. Santa Clara

Ecatepec 55540 Edo. Mexico

Toll Free: 01-800-839-1200

www.americanstandard.com.mx

American Standard 9118.111.020 Installation guide

Brand: American Standard

Model: 9118.111.020

Category: Sanitary ware

Type: Installation guide

Download PDF

report

American Standard 9118.111.020 Installation guide

American Standard 9118.111.020 Installation guide

Related papers

Other documents