7301982-100
Introduction: Thank you for selecting our products...products which been the
benchmarks of fine quality for years. To help insure that the installation process will
proceed smoothly, please read these instructions carefully before you begin. Also,
review the recommended tools and materials list; carefully unpack and examine your
new plumbing fixture.
Channel Lock Pliers
Regular Screwdriver
Recommended Tools
Phillips Screwdriver
Drill
Tape
Measure
Pencil Square
Level
SAVE FOR FUTURE USE
CAUTION: PRODUCT IS FRAGILE. TO AVOID DAMAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
ACRYLIC SHROUD FOR
AMERICAN STANDARD
SELECTRONIC
®
FAUCETS
USED ON SINK MODEL’S:
Lucia
®
0145. series
Murro
®
0954 0955 & 0958. series
INSTALLATION INSTRUCTIONS
!
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013
1
Adjustable Wrench
Shown with Murro 0955.001EC lavatory (sold separately)
1234567891011
12345678910
11 12 13 14 15 16 17 18 19 20 21 22 23 24
Rough-In
Dimensions
SUPPLIES
FINISHED WALL
FINISHED WALL
FINISHED FLOOR
POWER
SUPPLY
THERMOSTATIC
MIXING VALVE
P-TRAP
170mm
(6-11/16")
265mm
(10-7/16")
410mm
(16-1/8")
FOLLOW LOCAL CODES
FOR SHIK HEIGHT.
402mm
(15-13/16")
147mm
(5-3/4")
7301982-100
2
1
LOCATE CENTER OF FIXTUREALIGN AND CENTER THE SHROUD
1. Align and center the APRON to the bottom of the sink and mark
the top edges (right & left).
3
ALIGN THE TEMPLATE
4
TAPE THE TEMPLATE TO THE WALL
1. Use a small drill to drill all pilot holes on the template for the
Brackets, Power Supply and Mixing Valve.
1. Align the Template to the top edge and center line of these marks.
A section may be cut out of the Template to clear the Supply Valves
and P-Trap.
1. Draw a line and locate the center between the two marks.
2
C
L
1
1
1
7301982-100
5
MOUNT BRACKETS
1. Depending on the wall material, install the Brackets with appropriate Wall
Anchors for the suggested #10 Screws (not provided) to install Brackets.
7
INSTALL FAUCET
6
INSTALL MIXING VALVES
1. Install Mixing Valves with appropriate Wall Anchors for a suggested
#8 Screw.
2. Install Hot and Cold Shut-off Valves.
3
Fig. 7b
1. Insert WIRES, FLEX HOSE and SPOUT SHANK through center hole
of mounting surface. Fig. 7a.
2. Assemble "C" WASHER, STAR WASHER and LOCKNUT onto
threads of SPOUT SHANK from underside of mounting surface. Fig. 7b.
3. Align FAUCET and tighten LOCKNUT. Fig. 7b.
Fig. 7a
FOLLOW ALL INSTALLATION INSTRUCTIONS
PROVIDED WITH FAUCET KIT
1
1
2
2
1
1
7301982-100
ATTACH HOSES
1. Attach the Mixing Valve Hoses to the Hot and Cold Shut-Off Valves.
2. Attach the Faucet Hose to the Power Supply Valve
4
8
TEST INSTALLED FAUCET
1. Turn on Supply Valves and check for leaks.
2. Check operation of the Faucet and install the Box Covers.
10
INSTALL SHROUD
1. Position Shroud over the Brackets, align the holes, and install
Screws and Decorative Covers, (4) places.
11
ATTACH MIXING HOSE
1. Attach the Mixing Hose to the Power Supply Valve.
2. Follow the wiring instructions provided with the Faucet Kit and make
connections.
3. Connect the P-Trap to the Faucet Tailpiece.
9
1
1
1
1
1
1
1
2
3
2
2
2
/
