Extech Instruments CL500 User manual

Category
Measuring, testing & control
Type
User manual
USERGUIDE
FreeandTotalChlorineTester
PatentPending
ModelCL500
CL500-en-GB_V1.3 1/16
2
Introduction
CongratulationsonyourpurchaseoftheCL500chlorinetester.TheCL500isarevolutionaryfirst
ofitskindmeasurementdevicethatmeasuresfreeandtotalChlorinefrom0.00to3.50ppm.
TheelectrodemethodemployedisapprovedbytheU.S.EnvironmentalProtectionAgency(EPA)
asanacceptablemethodforwastewatercompliancemonitoringoftotalchlorine.Forthistype
ofelectrodemethod,areagenttabletmustbeaddedtothemeasurementsolutionbefore
testing.TheadvantagesoftheCL500fortheuserinclude:easytouseandmaintain,high
accuracy,selfcalibration,andfastresponse.Thismeterisshippedfullytestedand
calibrated
and,withproperuse,willprovideyearsofreliableservice.Pleasevisitourwebsite
(www.extech.com)tocheckforthelatestversionofthisUserGuide,ProductUpdates,and
CustomerSupport.
Applications
TheCL500canbeusedwhereverameasurementofthetotalchlorineinwaterasneeded.This
isalsoreferred to astotalresidualchlorine.Itmeasuresthetotalofallchlorinepresentinall
forms,includingdissolvedfreechlorine,chloramines,hypochlorousacid,andhypochloriteion.
Typical applications include Total Chlorine
measurements of discharge water from water
treatment plants, public drinking water supplies and cooling towers, and free chlorine
measurements of the disinfectant properties in swimming pools and cooling water
applications.
MeterDescription
CL500FrontPanelDescription
1. TestBottleChamber
2. TestBottleChamberlatch
3. LCDdisplay
4. POWERbutton
5. HOLDbutton
6. RECMAXMINbutton
7. ZERObutton
8. TESTCALbutton
9. Testbottle
CL500-en-GB_V1.3 1/16
3
GettingStarted
EquipmentRequired
Achlorinetestrequiresa10mlsamplebottle,reagentpowderfortestingFreeandTotal
chlorine,andtheCL500meter.
MeasurementProcedure
Calibrationconsiderations
1. Ensurethatthemeterhasbeencalibratedpriortouse.
2. Refertothecalibrationsectionforthisprocedure.
Testsample“Zero”measurement
Note:Priortotesting,setthemetermodetoFREEorTOTALbasedonthedesiredtest
method.SeeModeSelection.
1. ThemetershouldbeintheOFFposition.
2. Placethetestsample,withouttheDPDpowderadded,intothesamplebottleuptothe
10mLline(minimum).Place
thecaponthebottleandtighten.
3. Cleananddrytheoutsideofthesamplebottletoensureacleansurface.
4. Openthecoverofthetestchamberandinsertthebottlecompletelyintothechamber.
5. Lineupthewhitemarkonthebottlewiththewhite
markofthetestchamber.
6. Closethecoverandlockitinplace.
7. Pressthe“POWER”buttontoturnthemeterON.Thedisplaywillshow‘Free’or‘Total’
for1secondandthen‘CAL0’.Themeterisnowreadyforthe“zero”test.
8. Pressthe“Zero”button,
thedisplaywillflash“tEST”andthen“0.00”ppm.TheZeroTest
isnowcomplete.Donotpowerdownthemeter.
MeasurementofTestSolution
1. Openthetestchamberandremovethetestbottle.
2. AddtherequiredDPDpowder(FreeorTotal)intothesampleandthenshakefor20
secondsuntilcombined.Placethecaponthebottleandtighten.
FortheFreeChlorinetest,usetheFreeChlorineDPDpowder
Forthe
TotalChlorinetest,usetheTotalChlorineDPDpowder
3. Cleananddrytheoutsideofthesamplebottletoensureacleansurface.
4. Wait2minutebeforeplacingthetestbottleintothemetertoallowtimeforthesolution
tomixthoroughly.
5. Openthecoverof
thetestchamberandinsertthebottlecompletelyintothechamber.
6. Lineupthewhitemarkonthebottlewiththewhitemarkofthetestchamber.
CL500-en-GB_V1.3 1/16
4
7. Closethecoverandlockitinplace.
8. Pressthe“Test”button.Thedisplaywillflash“tEST”forabout10secondsandthenthe
resultswillappear.
Note:Cleanandrinsethetestbottlewithdistilledwateraftereachtest.
DataHOLD
PresstheHOLDbuttononcewhiletakingameasurementtofreezethevalueonthedisplay.
PressHOLDagaintoreleasethedataholdfunction.
DataRecord(MAX/MINReadings)
1. TheDatarecordfunctionrecordstheMAXandMinreadings.
2. Press"REC"buttononcetobeginDatarecording.TheLCDwilldisplaythe"REC"symbol.
3. ToviewtheMAXvaluewhileintherecordingmodepress"REC"once.Thedisplaywillshow
themaximumreadingand“RECMAX"
willshowontheLCDdisplay.
4. Press"REC"buttononceagainand"RECMIN"willdisplayontheLCDalongwiththe
minimumreading.
5. ToerasetheMaxvalueandcontinuerecording,whileintherecordmode,momentarily
pressthe“Rec”button.Thedisplaywillshow“RECMAX”.
Momentarilypressthe“HOLD”
button,thedisplaywillnowshow“REC”.TheMaxvaluehasbeenerased.
6. ToerasetheMinvalueandcontinuerecording,whileintherecordmode,momentarilypress
the“Rec”button.Thedisplaywillshow“RECMAX”.Pressthe“REC”buttononceagainand
nowthe
displaywillshow“RECMIN”.Momentarilypressthe“HOLD”button,thedisplaywill
nowshow“REC”.TheMinvaluehasbeenerased.
7. ToexitRecordmode,pressthe“REC”buttonfor3seconds.Thedisplaywillreturntothe
currentreading.
ModeSelectionFreeorTotal
1. ThemetershouldbepoweredOFF.
2. Pressthe"HOLD"and"REC"buttonssimultaneouslyandthenmomentarilypressthe
"Power"button.
3. Pressthe"TEST"buttontoselectthedesiredfunction(FreeorTotal)Chlorine.
4. Pressthe"REC"buttontoconfirmandsavetheselectionintomemory.
5. Momentarily
pressthe“Power”buttontoturnoffthemeter.
AutoPowerOFF
TheautopowerofffeatureautomaticallyswitchestheCL500OFF10minutesafterthelastkey
press.
CL500-en-GB_V1.3 1/16
5
CalibrationProcedure
TheCL500canbecalibratedforFreeorTotalChlorinemeasurements.
Priortocalibration,settheMetertoeithertheFreeorTotalmodeandusethecorrect1.0ppm
solutionbottleforcalibratingFreeorTotalChlorine..
CalibrationProcedure
1. Pressthe“Power”buttontoturnthemeterON.ThedisplaywillshowFreeorTotalandthen
“CAL0”.
2. CleanthesidesoftheZeroChlorinesolutionbottle.
3. Insertitintothetestingchamberandlineupthewhitemarkonthebottlewiththewhite
mark
inthechamber.andclosethecoverandlatchit.
4. Pressthe“Zero”button,thedisplaywillflash “tEST”forabout10secondsandwillthen
show“0.00”.ppm.
5. PressandholdtheCALbuttonuntil“CAL”appearsonthedisplay.ReleasetheCALbutton.
6. MomentarilyPress
the"CAL"buttonandthedisplaythenshowthefollowing:
7. The meterisnowreadyfor"zerochlorine"calibration.
8. MomentarilyPressthe“CAL"button.TheLCDwillflash“CAL”for10secondsandwillthen
showthefollowingdisplay:
9. TheLCDwillthendisplay:
10. ZeroChlorinecalibrationisnowcomplete.Themeterisnowreadyforthe1.00ppmTest
solutioncalibration.
0.00
CAL ppm
CAL
0.00 ppm
1.00
CAL ppm
CL500-en-GB_V1.3 1/16
6
11. Cleanthesidesofthe1.00ppmChlorinestandard(FreeorTotal)solutionbottleand
insertitintothetestingchamber.
12. Lineupthewhitemarkonthebottlewiththewhitemarkinthechamber,close,and
latchthecover.
13. MomentarilyPressthe"CAL"button;thedisplay
willflash“CAL”andthenshowthe
following:
14. WhencalibrationiscompletetheLCDwillreturntothenormaloperatingmodeand
measurethetestsolution.Thedisplayshould show1.00ppm.
15. Themeterisnowreadytomeasuretestsolutions.
CAL
1.00 ppm
CL500-en-GB_V1.3 1/16
7
Maintenance
LowBatteryIndication
Whenthebatteriesbecomeweakthe iconwillappearinthedisplay.Refertothebattery
replacementinformationbelow.
BatteryReplacement
1. Onthebackofthemeter,removethe2screwsholdingthebatterycoverinplace.
2. Replacethesix(6)AAAbatteries,observingpolarity.
3. Replacethebatterycompartmentcover
BatterySafetyReminders
1. Neverdisposeofbatteriesinafire.Batteriesmayexplodeorleak.
2. Nevermixbatterytypes.Alwaysinstallnewbatteriesofthesametype.
Neverdisposeofusedbatteriesorrechargeablebatteriesinhouseholdwaste.
Asconsumers,usersarelegallyrequiredtotakeusedbatteriestoappropriate
collectionsites,
theretailstorewherethebatterieswerepurchased,orwherever
batteriesaresold.
Disposal:Donotdisposeofthisinstrumentinhouseholdwaste.Theuseris
obligatedtotakeendoflifedevicestoadesignatedcollectionpointforthe
disposalofelectricalandelectronicequipment.
Electrodeconsiderations
TheCL500ChlorineElectrodearrivesinafactorycleanedconditionandisreadytobeused.The
electrodewillperformbestandyieldmorestablereadingsafterthefirstfewtests.
CleaningtheMeter
Occasionallywipethemeterhousingwithadampcloth.Donotuseabrasivesorsolvents.
CL500-en-GB_V1.3 1/16
8
Specifications
Display LCDsize:1.6x1.3”(41mmx34mm)
Operatingconditions 0to50°C(32to122°F)and<80%RH
Chlorinerange 0.00to3.50ppm(TotalChlorine)
0.00to3.50ppm(FreeChlorine)
Resolution 0.01
ppm
Accuracy 0.02[email protected]ppm
LightSource LED,525nm
LightDetector PhotoDiode
ResponseTime Lessthan10seconds
SampleVolume 10mLminimum
SampleTime Approximately1second
Power Six1.5Vbatteries
PowerConsumption StandByMode:approx.4mADC
TestingMode:approx.12mADC
Dimensions 155x76x62mm
(6.1x3.0x2.4”);320g(0.70lbs.)
AutoPowerOFF AutomaticallyswitchesOFF10minutesafterthelastkeypress
Method ThemeasuringmethodisanadaptationoftheUSEPAmethod330.5
andstandardmethod4500ClG
Copyright©20142016FLIRSystems,Inc.
Allrightsreservedincludingtherightofreproductioninwholeorinpartinanyform
ISO9001Certified
www.extech.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Extech Instruments CL500 User manual

Category
Measuring, testing & control
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI