Cooper Lighting OAWC-P-120W-R Installation guide

Brand: Cooper Lighting

Model: OAWC-P-120W-R

Category: Motion detectors

Type: Installation guide

This manual is also suitable for

Installation Instructions

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Maximum coverage area may

vary somewhat according to room

shape and the presence of obstacles.

The NEMA WD 7 Guide and robotic

method were utilized to verify

coverage patterns.

24’

(7.3 mm)

Minor Motion, IR

Major Motion, IR

20’

(6 mm)

8’

(2.4 mm)

8’

(2.4 mm)

24’

(7.3 mm)

20’

(6 mm)

10 ft

(3 mm)

12’

(3.7)

12’

(3.7)

6 ft

(1.7 mm)

15 ft

(4.6 mm)

24 ft

(7.3 mm)

50 ft

(15.3 mm)

Model # OAWC-P-120W

Model # OAWC-P-120W-R

Passive Infared Wall/Corner Mounted Low

Voltage Occupancy Sensor

• Readallinstructionsonbothsidesofthissheetrst

• Planallcomponentlocationscarefully

• InstallinaccordancewithALLlocalcodes

• Forindooruseonly

• ForUsewithGreengateSwitchpacks&SystemsOnly

• DonotrunanyGreengateLowVoltageWiringinthe

sameconduitaspowerconductors

General Information

Technology:PassiveInfrared(PIR)

Power Requirements:

Input:

• 10-30VDCfromGreengateSwitchpackorGreengate

system.Maximumcurrentneededis25mApersensor

Output:

• OpencollectoroutputtoswitchuptotenGreengate

Switchpacks.BASwithIsolatedFormCRelay(-Rmodel)

IsolatedFormCRelayRatings:1A30VDC/VAC

Time Delays:Self-Adjusting,15seconds/test(10minAuto),

orSelectable5,15,30minutes

Coverage:1200sq.ft.

Light Level Sensing:0to300foot-candles(-Rmodel)

Operating Environment:

• Temperature:32°F–104°F(0°C–40°C)

• RelativeHumidity:upto90%non-condensing

Housing:

• Mediumimpactinjectionmoldedhousing

PolycarbonateresincomplieswithUL94V0

Size:4.4"x3.4"x2"(112mmx86.4mmx50.8mm)

LED Indicators:RedindicatesPIRdetection

Speciﬁcations

Description

TheOAWC-PWall/CornerMountLowVoltageOccupancySensorisaPassiveInfrared(PIR)motion sensinglightingcontrol,used

forenergysavingsandconvenience.Whenmotionisdetected,thebluewireiselectronicallyconnectedtotheredwire,energizing

therelayintheswitchpacktoturnONtheload.Ifvacancyisdetected,thebluewireisdisconnectedfromthered,causingtherelay

toopenturningOFFtheload.Theredleadis10to30VDCsupply,theblackleadiscommonandtheblueistherelaycontrol.

PIR Technology

Thesensor’ssegmentedlensdividestheeldofviewintosensorzonesanddetectsthechangesintemperaturethatarecreated

whenaperson,orpartofapersonassmallasahand,passesintooroutofasensorzone.

Thesensorincludesself-adaptivetechnologythatcontinuallyadjuststoconditionsbyadjustingsensitivityandtimedelayinreal-

time.Byadjustingsensitivityandtimedelayautomatically,thesensorismaximizingthepotentialenergysavingsthatareavailablein

theparticularapplication.

TheDaylightingfeature(-Rmodelonly)preventslightsfromturningONwhentheroomisadequatelyilluminatedbynaturallight.

TheWalk-ThroughfeaturemaximizesenergysavingsbynotleavingthelightsONafteramomentaryoccupancy.Thesensor

willswitchthelightsONwhenitdetectsapersonenteringthearea.Ifthesensordoesnotcontinuetodetectmotion30seconds

following theinitialactivation,itwillautomaticallygotoashorter2minutetimedelay.

InAutomaticOnMode,thelightsturnONwhenapersonenterstheroom.InManualONMode,thelightsareturnedONby

activatingamomentaryswitch(model#GMDS-*)thatisconnectedtothesensor.Whenusedwith2levellighting(-Rmodelonly),

bi-levelAutomaticONcanbeachievedwhichallowsZone1tocomeONautomaticallyuponoccupancy.Zone2doesnotcomeON

unlesstheoccupantpressestheoptionalmomentaryswitch.

Location

Themaximumcoverageareamayvarysomewhataccordingtoroomshapeandthe

presenceofobstacles.Followthecoveragediagramconcerningmajorandminormotion

coverage.Thesensormusthaveaclearviewoftheareatobecontrolled.Thesensorwill

not“see”throughglass.Mountingheightshouldnotexceed12feet.Optimummounting

heightis10feet.Mountthesensorsothedevicefacestheopenportionoftheroom and

arefacinganearbywall,door,window,orotherobstructingobject.Avoidpointinginto

hallways.Topreventfalseactivation,thesensorshouldbemountedawayfromtheair

supplyductaminimumof4to6feet.Mountingatxtureheightismosteffective.For

typicalplacementrefertoLocationDiagram.

Installation

TheOAWC-P-120Wcanbemountedtothewall,ceiling,junctionboxorroundxturewithraceway.

Wiring

CAUTION: Before installing or performing any service on a Greengate system, the power MUST be turned OFF at the

branch circuit breaker. According to NEC 240-83(d), if the branch circuit breaker is used as the main switch for a

ﬂuorescent lighting circuit, the circuit breaker should be marked “SWD”. All installations should be in compliance with

the National Electric Code and all state and local codes.

NOTE REGARDING COMPACT FLUORESCENT LAMPS: The life of some compact ﬂuorescent lamps (CFLs) is shortened by

frequent automatic or manual switching. Check with CFL and ballast manufacturer to determine the effects of cycling.

1. MakesurepoweristurnedOFFatthebranchcircuitbreaker.

2. Wireunitsasshowninwiringdiagramsperapplicablevoltagerequirements.(Usetwist-onwireconnectorsforall

connections)CAPALLUNUSEDWIRELEADS.

3. Mountunittowall,ceiling,junctionbox,orroundxturewithraceway.

4. TurnpowerbackONatthebranchcircuitbreakerandwait2minutesfortheunittostabilize.

5. Makenecessaryadjustments.(SeeCheckoutandAdjustmentssection)

Occupancy Sensor Mounted to Wallboard

Occupancy Sensor Mounted to Round Fixture with Raceway

Occupancy Sensor Mounted to Octagon Box

Occupancy Sensor Mounted to Drop Ceiling

Location Diagram

Coverage

Occupancy Sensor Mounted to Octagon Box with Mud Ring

SENSOR WIRE LEAD LEGEND

Black (Common)

Red (10-30 VDC)

Blue (Control)

Yellow (Control)

Brown (Switch-Blue Lead Control)

Brown/White (Switch-Yellow Lead Control)

Sensor’s Isolated Relay

Orange (Normally Open)

Gray (Common)

Purple (Normally closed)

Yellow

Blue

Red

Black

Recommended Wire: 18-3 AWG stranded non-shielded

Brown/White

Brown

Gray

Purple

Orange

Optional Greengate GMDS Switch-

Blue Control Lead-Manual ON/OFF

To Additional Sensors.

Maximum of 5 sensors

per switchpack.

Switchpack

Blue

Load 1

White

**Hot

Blue

Hot

Neutral

Line

**Use Black Lead for 120 VAC

Use Orange Lead for 277 VAC

Cap Unused Lead

Black (Common)

Red (15 VDC)

Blue (Control)

One Sensor, One Switchpack

P/N 9850-000140-01

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, Georgia 30269

www.coopercontrol.com

Printed in Malaysia

Warranties and Limitation of Liability

DIP Switch Settings

Troubleshooting

Pleaserefertowww.coopercontrol.comundertheLegalsectionforourtermsandconditions.

Checkout and Adjustment

Issue Possible Causes Suggestions

Lights

Will Not

Turn ON

automatically

WallswitchOFF TurnwallswitchON

Iflowvoltageswitchoptionisused,lights

mayhavebeenturned-offmanually

Presslow-voltageswitch

DaylightingFeatureEnabled

IfalllightsarerequiredtoturnONadjustDIP

Switch10and/ordaylightpotentiometer

Powerinterruption Checkincomingvoltageand/orwiring

Lights

Will Not

Turn ON

manually

DaylightingFeatureEnabled

IfalllightsarerequiredadjustDIP

Switch10and/ordaylightpotentiometer

Powerinterruption Checkincomingvoltageand/orwiring

If lights will still not turn ON, set sensor to override mode and call Technical Services at 1-800-553-3879

Lights

Will Not

Turn OFF

automatically

Override MakesuresensorisnotinOverrideMode(DIPSwitch8up)

Sensorinstalledclosetoanairvent

Sensorsshouldbeinstalled4-6feetaway

fromanyairventandoutofheavyairow

Sensorinstalledclosetoindirectlighting Sensorsshouldbemountedawayfromindirectlighting

Self-adjust

Itmaybepossiblefortheunittohaveself-adjusted

thetimedelaytoa30minutedelay.Ifthelightsdo

notturnOFFafter30minutesfollownextstep

30MinuteDelay

Maximumtimedelayis30Minutes.CheckDIP

SwitchestoverifyDIPSwitchsettings.Iflightsdo

notturnOFFatthesettimedelay,checknextstep

PIRactivatedbyheatsourceotherthanoccupant MoveDIPSwitch5UP

Bypass

Checkwiringtomakesuresensor

orswitchpackarenotbypassed

Lights

Will Not

Turn OFF

automatically

Override MakesuresensorisnotinOverrideMode(DIPSwitch8up)

If lights will still not turn OFF, call Technical Services at 1-800-553-3879

AdjustmentsshouldbemadewiththeHVACsystemON.Useonlyinsulatedtoolstomakeadjustments.

Self-Adjust

SensorisshippedintheSelf-AdjustMode.ThisappliestotimedelayandPIRsensitivity.Inpreparationforthe

InstallerTest,thetimedelayissetto15seconds,afterthesensorisinstalled,poweredONandhasstabilized,the

unitwilltime-out15secondsafterthelastmotiondetected.Coverageandsensitivitycanbeconrmedbywatching

theRed(PIR)indicatorLEDsonthefrontofthesensor,whilemovingaroundtheroom.

1. WalkaroundtheroomandmonitorLEDs.LEDsshouldonlyturnONforonesecondwitheachmotion.(IfLEDs

donotturnON,gotoInstallerAdjustments-SensitivityAdjustmentsSection)

2.Standstillsixtoeightfeetawayfromthesensorforveseconds.LEDsshouldnotturnON.(IfanyLEDturns

ON,noteLEDandgotoInstallerAdjustments–SensitivityAdjustmentsection)

3.Walkoutsidetheroomandwait15secondsforthelightstoturnOFF.

(IflightsdonotturnOFFgotoInstaller

AdjustmentsSection)

4.Re-entertheroomtoactivatesensor.(IflightsdonotturnONgotoTroubleshootingSection)

5.TheunitwillremaininTestModefor5 minutesthenautomaticallyexitTestModeandgofor10min.Time

DelayUserModesetting.

Note:ToplaceintoTestMode,toggleDIPSwitch10outofitscurrentposition,wait3seconds,andthenbackintoitsoriginalposition.To

forceinto10minUserModemoveDipSwitches1and2down.(IfDIPSwitches1and2arealreadydown,toggleDIPSwitch1outofitscurrent

position,wait3

seconds,andthenbacktoitsoriginalposition)WhileinTestMode,theLEDswillashonceper1/4second.

Installer Adjustments

Sensitivity Adjustments

PIR Sensitivity

1. Standindifferentareasoftheroomandwaveyourhands.

2.IftheRedLEDdoesnotturnON,checkforanyobstructions.

3.Standstillsixtoeightfeetawayfromsensorforveseconds.LEDshouldnotturnON.

4.IfRedLEDturnsONwithoutmotionorisconstantlyONadjustPIRsensitivityto50%bymovingDIPSwitch5U P.

Hot

Neutral

Line

Load 1

Black

Red

Blue

Purple

Gray

Orange

Switchpack

Blue

**Hot

**Use Black Lead for 120VAC

Use Orange Lead for 277VAC

Cap Unused Lead

White

Hot

Neutral

Line

Load 2

Switchpack

Blue

**Hot

**Use Black Lead for 120VAC

Use Orange Lead for 277VAC

Cap Unused Lead

White

Yellow

Brown

Brown/White

Optional Greengate GMDS Switch-

Blue Control Lead- Manual on/off

Red (15VDC)

Black(Common)

Blue (Control)

SENSOR WIRE LEAD LEGEND

Black (Common)

Red (10-30VDC)

Blue (Control)

Yellow (Control)

Brown (Switch-Blue Lead Control)

Brown/White(Switch-Yellow Lead Control)

Sensor's Isolated Relay

Orange (Normally Open)

Gray (Common)

Purple (Normally Closed)

Red (15VDC)

Black(Common)

Blue (Control)

To Additional Switchpacks

10 switchpacks Maximum

Activation Activation

PIR Sensitivity

Daylighting Mode

Lighting SweepOverride

LEDs

50%

5 Minutes

15 Minutes

30 Minutes

Auto

Manual

DIP Switch

Power Pack One Power Pack Two

(-R model only)

Full

Disable

Enable

Auto*

*Self-Adjusts to

10 min. user mode

Default =

Time Delay

Disable

Enable

Walk-Through Mode

Half

Full

12345678910

One Sensor, Multiple Switchpacks Field-of-view outside the space

1. AdjustPIRsensitivityto50%bymovingDIPSwitch5up.

Daylight Adjustments

Ifthisfeatureisnotneeded,leavethelightlevelatmaximum(fullyCW).

TheDaylightingfeature(-Rmodelonly)preventsthelightsfromturningONwhentheroomisadequatelyilluminated

bynaturallight.Ifthereisenoughlightintheroomregardlessofoccupancy,thesensorwillholdthelightsO F F.Ifthere

isnotenoughlightintheroom,thesensorwillallowthelightstoturnONwhenoccupied.

Full and Half Logic Modes(SeeDIPSwitchlegend):

InbothFullandHalfLogicmodes,lightsconnectedtotheyellowcontrolleadwillnotturnONuponoccupancy

activation,shouldtheambientlightlevelexceedthepresetfoot-candlelevel.

After activation:

FullLogicMode–shouldtheambientlightlevelexceedthepresetfoot-candlelevel,thelightsconnectedtothe

yellowcontrolleadwillturnOF F.ThelightswillremainOFF,untiltheambientlightlevelfallsbelowthesetpoint.

HalfLogicMode–theoutputstateoftheyellowcontrolleadwillnotchangewithambientlightchanges,after

occupancyactivation.Iftheamountofnaturallightavailablerisesabovethesetpoint,thedaylightsensorwillnotturn

thelights

OFFwhileoccupancyisbeingdetected.

Note:Setthelightlevelwhentheambientlightisatthelevelwherenoarticiallightisneeded.Inorderforthis

featuretofunction,theyellowcontrolleadmustbewired.

1. WiththeloadON,putthesensorintoTestMode.ToplaceintoTestMode,toggleDIPSwitch10outofitscurrent

position,wait3secondsandthenbackintoitsoriginalposition.

2.SetDIPSwitch10toFullorHalfLogicMode.

3.Setthelightleveltominimum(fullyCCW).

4.Leavetheroomandletthesensortime-outsolightsareOF F.EnterthespaceandlightsshouldremainOFF.

5.MakesurenottoblockthesensorfromthedaylightsourceandadjustthelightlevelpotentiometerCWinsmall

incrementsuntilthelightsareON.(Pause5secondsbetweeneachadjustment)

6.OncethelightsareON,theloadconnectedtothesensorwillnotturnONiflightlevelsareabovethe

currentillumination.

Time Delay Adjustments

Peoplewhoremainverystillforlongperiodsoftimemayneedalongertimedelaythanthedefaultsettingof10

minutes.AslongasAutoisenabled,thesensorwillrespondtoeachpairoffalse-OFFswithnonormalOFFinbetween,

byalternatelymakingslightadjustmentstoeithertimedelay(by2minuteincrements)orsensitivity,sothereshouldbe

noneedformanualadjustment.Ifmanualadjustmentisdesired,refertoTimeDelaysettingsinDIPSwitchlegend.

ResetsensortimedelaytofactorysettingsbymovingDIPSwitches1and2down.(IfDIPSwitches1and2are

alreadydown,toggleDIPSwitch1outofitscurrentposition,wait3seconds,andthenbacktoitsoriginalposition)

Automatic Mode

InAutomaticONMode,thelightsturnONwhenapersonenterstheroom.Ifoptionalmomentarylowvoltage

switchesareusedalongwithAutomaticONMode,activatingtheswitch(es)whiletheloadisONturnstheloadO F F.

WhentheloadisturnedOFFmanually,aslongasthesensorcontinuestodetectoccupancytheloadsstayO F F.After

thetimedelayexpires,thelightsstayOFFandthesensorgoesbacktoAutomaticONMode.Forwiringinformationfor

theoptionalmomentarylowvoltageswitch(es),pleaseseethewiringsectionoftheinstallationinstructions.

Manual Mode

InManualONMode,theoptionalmomentarylowvoltageswitch(es)isrequired

toturntheload(s)ON.Onceactivated

thesensorwillmaintainthelightsONuntilmotionceasesandthetimedelayexpires.Whiletheroomisoccupiedthe

BASrelayremainsactive.Afterthetimedelayexpires,theload(s)willautomaticallybeturnedOFFandtheswitch(es)

mustbeusedtoturntheload(s)ONunlessthereismotiondetectedwithinthe10secondre-triggerperiod.

Lighting Sweep Option

Ifselected,thisDIPSwitchoptionforcesaninitial60seconddelayupon“power-up”topreventfalseactivationin

buildingswithcomputercontrolsystems.

1. MoveDIPSwitch9U P.

Override

TheOverridesettingallowsthelightstoremainONintheunlikelyeventofsensorfailure.

1. MoveDIPSwitch8U P.

WhileinOverrideMode,theoptionallowvoltagemomentaryswitch(es)willtogglethelightingload(s).

Cooper Lighting OAWC-P-120W-R Installation guide

Brand: Cooper Lighting

Model: OAWC-P-120W-R

Category: Motion detectors

Type: Installation guide

This manual is also suitable for

Download PDF

report

Cooper Lighting OAWC-P-120W-R Installation guide

This manual is also suitable for

Cooper Lighting OAWC-P-120W-R Installation guide

Related papers

Other documents