Altronix eBridge1PCTX Installation guide

Altronix
Brand
Altronix
Model
eBridge1PCTX
Category
PoE adapters
Type
Installation guide

This manual is also suitable for

Altronix eBridge1PCTX is a PoE+ over Coax solution that enables fast 10/100 Base-T Ethernet digital communication to be transmitted over Coax cable. The eBridge1PCTX in turn delivers that PoE+ compliant power to a PoE enabled camera or IP device. These plug and play units facilitate system upgrades from analog to IP cameras/devices utilizing existing legacy Coax and eliminating the costs and labor associated with installing new network cabling. In addition, data transmission over the Coax is possible up to 457m in comparison to 100m Ethernet maximum distance.

Altronix eBridge1PCTX is a PoE+ over Coax solution that enables fast 10/100 Base-T Ethernet digital communication to be transmitted over Coax cable. The eBridge1PCTX in turn delivers that PoE+ compliant power to a PoE enabled camera or IP device. These plug and play units facilitate system upgrades from analog to IP cameras/devices utilizing existing legacy Coax and eliminating the costs and labor associated with installing new network cabling. In addition, data transmission over the Coax is possible up to 457m in comparison to 100m Ethernet maximum distance.

eBridge1PCRX/PCTX - 1 -
PLUS
Overview:
The eBridge1PCRX and eBridge1PCTX are CAT5 to Coax cable Ethernet adapters media converters that deliver data and
power over the coax cable in a PoE+ compliant format. The paired set enables fast 10/100 Base-T Ethernet digital commu-
nication to be transmitted over Coax cable. An eBridge1PCRX receiver sends power over the coax to the eBridge1PCTX
transmitter under PoE protocol. The eBridge1PCTX in turn delivers that PoE+ compliant power to a PoE enabled camera
or IP device. The eBridge1PCRX will not deliver power to non compliant devices, thus avoiding accidental power turn into
improperly connected analog cameras. These plug and play units facilitate system upgrades from analog to IP cameras/
devices utilizing existing legacy Coax and eliminating the costs and labor associated with installing new network cabling.
In addition, data transmission over the Coax is possible up to 457m in comparison to 100m Ethernet maximum distance
(see Maximum Length of Coax Type vs. Camera Power/PoE Class, pg. 3). A maximum range from head end to the PoE
camera/device is 610m taking into consideration that up to 100m of structured cable may be deployed at each end.
Features:
Agency Listings:
• UL/CULListedforInformation
TechnologyEquipment(UL60950-1).
• CEapproved.
• C-Tickcompliant.
Input:
• 24VDCto56VDCClass2powersupply
(polarityobserved).
Power Consumption (under maximum load):
• eBridge1PCRX:24VDC/1,500mA,56VDC/900mA.
eBridge1PCTX(30W):PoweredbyeBridge1PCRX.
eBridge1PCT(15W):PoweredbyeBridge1PCRX.
Ethernet:
• Connectivity:RJ45,auto-crossover.
• Wiretype:4-pairCAT5orbetterstructuredcable.
• Distance:upto100m.
• Speed:10/100 BaseT, half/full duplex, auto negotiation.
PoEcomplianttoIEEE802.3af(15W)andPoE+
complianttoIEEE802.3at(30W)Deliveredto
camera by eBridge1PCTX. Power provided by
eBridge1PCRX to eBridge1PCTX by PoE protocol.
• Throughputisratedtopass25mbpsofdataat
distances up to 457m. With proper headend
equipment this supports Megapixel,HD720,HD1080.
Coax:
• Distance:upto457m(see Maximum Length of Coax
Type vs. Camera Power/PoE Class, pg. 3) for power
delivery of coax.
• Connectivity:BNC,RG-59/Uorsimilar.
LED Indicators:
• eBridge1PCRX:
BlueLED-Coaxlinkconnection.
Green - PoE ON.
Green - Power ON.
LED Indicators (cont’d):
• eBridge1PCRX:
YellowandGreenLED(RJ45)IPLinkstatus,
10/100 Base-T/active.
• eBridge1PCTX:
BlueLED-Coaxlinkconnection.
GreenLED-PoEfromeBridge1PCR.
Environmental:
• Operating Temperature:
eBridge1PCRX:
15W: -- 4ºF to 113ºF (--20ºCto+45ºC).
30W for 24VDC: --4ºFto98.6ºF(--20ºCto+37ºC).
30W for 48VDC: -- 4ºF to 113ºF (--20ºCto+45ºC).
eBridge1PCTX: ---4ºFto120.2ºF(--20ºCto+49ºC).
• Storage Temperature: --22ºto158ºF(--30ºto+70ºC).
• Humidity:20to85%,non-condensing.
Functions:
• Autodetectionandprotectionoflegacy
non-PoE cameras/devices.
Applications:
• RetrofitdigitalIPcamerasinananalogCCTV
installation.
• WorkswithMegapixel,HD720,HD1080andVGA
(SD)cameras(see note, pg. 2).
• ExtendNetworklinkdistanceinanindustrial
environment over 610m (see note, pg. 2).
• UpgradedeployedCCTVCoaxtoadigitalnetwork
in Retail, Hospitality, Arenas, Casinos, Airports,
Schools,Hospitals,Transportation,etc.
Mechanical:
• Dimensions(WxLxHapprox.):
eBridge1PCRX:
3.5”x4.375”x1”(88.89mmx111.125mmx25.4mm)
eBridge1PCTX:
2.5”x4.375”x1”(63.5mmx111.125mmx25.4mm)
eBridge1PCRTX - IP and PoE+ over Coax Solution
eBridge1PCRX Receiver and eBridge1PCTX Transceiver kit
Installation Guide
Rev. 022213
I.T.E. 43KC
Z1409
- 2 - eBridge1PCRX/PCTX
Installation Instructions:
WiringmethodsshallbeinaccordancewiththeNationalElectricalCode/NFPA70/ANSI,andwithalllocalcodesand
authoritieshavingjurisdiction.WiringshouldbeULListedand/orRecognizedwiresuitablefortheapplication.
eBridge1PCTX and eBridge1PCRX are not intended to be connected to outside plant leads and should be installed
indoors within the protected premises. eBridge1PCTX and eBridge1PCRX are intended for indoor use only.
1. eBridge1PCRX installation:
a. Secureunittodesiredmountingsurfacewithaproperfasteningdeviceutilizingtheunit’smountinghole
(Fig. 2a, pg. 3).Unitshouldbemountedinproximitytoethernetswitch/network,NVRorvideoserver.
b.Connect24VDCto56VDCClass2powersupplytowireinsertconnector[Power---Input+](polarityobserved)
(Fig. 1, pg. 2).Use22AWG-16AWGwireforthisconnection.
c. Connectstructuredcablefromethernetswitch/NVR(networkvideoserver)toRJ45jackmarked[10/100BaseT]
(Fig. 2, pg. 3).
d.ConnectCoaxcabletoBNCconnectormarked[Coax](Fig. 2, pg. 3).
2.eBridge1PCTX installation:
a. Secureunittodesiredmountingsurfacewithaproperfasteningdeviceutilizingthecase’smountinghole
(Fig. 2a, pg. 3).Unitshouldbemountedinproximityofcamera/device.
b.ConnectstructuredcablefromIPcamera/devicetoRJ45jackmarked[10/100BaseT](Fig. 2, pg. 3).
c. ConnectCoaxcabletoBNCconnectormarked[Coax](Fig. 2, pg. 3).
Note:TheeBridge1PCRTXisdesignedtoaccommodateMegapixel,HD720,HD1080andVGA(SD)cameras.Itis
important to note that some high resolution and high frame rate cameras may demand faster headend processing ability,
such as a PC graphics card to present a quality image. If the headend processing equipment is insufficient in speed, the
image may show pixelation and latency. It is advisable to pretest system if unsure. Alternatively, frame rate and resolu-
tion may be reduced to accommodate system equipment.
Technical Specifications:
Parameter Description
Connections BNCforCoaxlink.RJ45forethernetlink.
Input power
requirements
24VDC/1,500mA,56VDC/900mA
Indicators
Blue:CoaxLink.
Yellow(RJ45connector):On-Link,Off-NoLink,Blinking-Activity.
Green(RJ45connector):On-100Base-TX,Off-10Base-T.
Green: Power.
Environmental
Conditions
OperatingAmbientTemperature:UL60950-1
eBridge1PCRX:
15W: -- 4ºF to 113ºF (--20ºCto+45ºC).
30W for 24VDC: -- 4ºFto98.6ºF(--20ºCto+37ºC).
30W for 48VDC: -- 4ºF to 113ºF (-- 20ºCto+45ºC).
eBridge1PCTX: -- 4ºFto120.2ºF(--20ºCto+49ºC).
Relativehumidity:85%,+/---5%
StorageTemperature:-- 4º to 158ºF (---20ºto70ºC)Storage
Operating Altitude: --1000to6,561.679ft.(--304.8to2000m).
Regulatory
Compliance
UL/CULListedforInformationTechnologyEquipment(UL60950-1).
CE approved. C-Tick compliant.
Weights(approx.) Product: 5.1 oz. (0.144kg),Shipping:7.76oz.(0.22kg)
Fig. 1 eBridge1PCRX eBridge1PCTX
Green LED
indicates
Power
Structured
Cable from
Ethernet Switch/NVR
Structured
Cable from
IP Camera/Device
Blue LED indicates
Coax Connection
Blue LED
indicates
Coax Connection
Green LED
indicates
Power
Yellow LED
indicates
PoE
Coax
Cable from
eBridge1PCT
24VDC-56VDC
--- Input +
Coax
Cable from
eBridge1PCR
eBridge1PCRX/PCTX - 3 -
Single PoE camera connection:
Fig. 2 Fig. 2a
Multiple PoE camera connection:
Fig. 3
Maximum Length of Coax Type vs. Camera Power/PoE Class:
Camera
Power/
PoE Class
Coax Type
RG59/U - 23AWG RG59/U - 22AWG RG59/U - 20AWG RG59/U - 18AWG RG6/U - 18AWG
Max. Length (meters)
13W/0 260.64 335.28 457.20+ 457.20+ 457.20+
4W/1 457.20+ 457.20+ 457.20+ 457.20+ 457.20+
6.5W/2 457.20+ 457.20+ 457.20+ 457.20+ 457.20+
13W/3 260.64 335.28 457.20+ 457.20+ 457.20+
19W 152.4 198.1 315.5 457.20+ 457.20+
25W 118.9 150.6 239.3 365.8 365.8
PoC (PoE+ over Coax)
457m max.
24VDC to
56VDC
Input
Ethernet Switch
PoE compliant
100m max.
100m max.
Coax
Structured Cable
Legend:
Mounting Hole
PoE Camera
eBridge1PCTX
eBridge1PCRX
NVR Network
Video Server
(Head End
Equipment)
www.altronix.com
SLOC
Link LED
Coax
10/100
Base-T
Power
LED
Blue LED Coax link status
RJ45 LEDs Yellow - Speed
Green - Activity
Green LED Power
I.T.E. 43KC
Z1409
Provides PoE/PoE+
eBridge1PCTX - Transceiver
I.T.E. 43KC
www.altronix.com
Input: 24VDC/1500mA, 56VAC/900mA (under maximum load)
Blue LED Coax link status
RJ45 LEDs Yellow - Speed, Green - Activity
Green LED Power and PoE
Z1409
Provides PoE/PoE+
SLOC
Link LED
Coax
10/100
Base-T
Power
LED
PoE LED
Power
Input
--- +
eBridge1PCRX - Receiver
PoE Camera
Ethernet Switch
NVR Network
Video Server
(Head End
Equipment)
PoE Camera
PoE Camera
PoE Camera
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
PoC (PoE+ over Coax)
457m max.
100m max.
100m max.
100m max.
100m max.
PoE compliant
100m max.
PoE compliant
100m max.
PoE compliant
100m max.
PoE compliant
100m max.
Coax
Structured Cable
Legend:
eBridge1PCRX
eBridge1PCRX
eBridge1PCRX
eBridge1PCRX
eBridge1PCTX
eBridge1PCTX
eBridge1PCTX
eBridge1PCTX
- 4 - eBridge1PCRX/PCTX
Altronix is not responsible for any typographical errors.
14058thStreet,Brooklyn,NewYork11220USA,718-567-8181,fax:718-567-9056
website:www.altronix.com,e-mail:[email protected],LifetimeWarranty,MadeinU.S.A.
IIeBridge1PCRTX G31N
MEMBER
Notes:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Altronix eBridge1PCTX Installation guide

Altronix
Brand
Altronix
Model
eBridge1PCTX
Category
PoE adapters
Type
Installation guide
This manual is also suitable for

Altronix eBridge1PCTX is a PoE+ over Coax solution that enables fast 10/100 Base-T Ethernet digital communication to be transmitted over Coax cable. The eBridge1PCTX in turn delivers that PoE+ compliant power to a PoE enabled camera or IP device. These plug and play units facilitate system upgrades from analog to IP cameras/devices utilizing existing legacy Coax and eliminating the costs and labor associated with installing new network cabling. In addition, data transmission over the Coax is possible up to 457m in comparison to 100m Ethernet maximum distance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents