Dell PowerSwitch S4048-ON Quick start guide

Brand: Dell

Model: PowerSwitch S4048-ON

Category: Network switches

Type: Quick start guide

S4048-ON Installation Guide

January 2019

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

trademarks may be trademarks of their respective owners.

2019 - 01

Rev. A06

Contents

1 About this guide............................................................................................................................................. 5

Related documents............................................................................................................................................................ 5

2 The S4048–ON switch.................................................................................................................................. 6

Introduction.........................................................................................................................................................................6

Features...............................................................................................................................................................................7

Physical dimensions........................................................................................................................................................... 7

Switch status......................................................................................................................................................................8

LED display..........................................................................................................................................................................8

LED behavior................................................................................................................................................................ 9

Prerequisites.......................................................................................................................................................................11

S4048–ON congurations............................................................................................................................................... 11

3 Site preparations.......................................................................................................................................... 12

Site selection..................................................................................................................................................................... 12

Cabinet placement............................................................................................................................................................12

Rack mounting.................................................................................................................................................................. 13

Switch ground................................................................................................................................................................... 13

Fans and airow................................................................................................................................................................13

Fan combinations........................................................................................................................................................13

Power................................................................................................................................................................................. 13

Storing components......................................................................................................................................................... 13

4 NEBS compliance.........................................................................................................................................15

Important information...................................................................................................................................................... 15

5 S4048–ON installation................................................................................................................................. 16

Unpack the switch............................................................................................................................................................16

Unpack.........................................................................................................................................................................16

Rack or cabinet hardware installation............................................................................................................................ 16

Rack mount safety considerations............................................................................................................................17

ReadyRails system installation...................................................................................................................................17

Two-post ush-mount conguration........................................................................................................................18

Two-post center-mount conguration.....................................................................................................................19

Four-post threaded conguration............................................................................................................................20

S4048-ON installation................................................................................................................................................21

1U front-rack installation............................................................................................................................................ 21

Ground cable...............................................................................................................................................................23

SFP+ and QSFP+ optic installation................................................................................................................................23

QSFP+ optic replacement.........................................................................................................................................24

Split QSFP+ ports to SFP+ ports............................................................................................................................ 24

Switch power-up..............................................................................................................................................................24

Contents

Power up sequence................................................................................................................................................... 24

6 Power supplies.............................................................................................................................................25

Components..................................................................................................................................................................... 25

AC power supply installation...........................................................................................................................................26

AC power supply replacement..................................................................................................................................27

DC power supply installation...........................................................................................................................................27

DC power connections..............................................................................................................................................29

DC labels..................................................................................................................................................................... 30

7 Fans..............................................................................................................................................................31

Components......................................................................................................................................................................31

Fan module installation.................................................................................................................................................... 32

Fan module replacement.................................................................................................................................................32

After S4048–ON installation.......................................................................................................................................... 32

8 Management ports...................................................................................................................................... 33

RS-232 console port access...........................................................................................................................................33

Micro USB-B console port access.................................................................................................................................34

Mounting the USB storage.......................................................................................................................................34

Before you install an OS.................................................................................................................................................. 35

Example of the grub bootloaderExample of ONIE.................................................................................................35

ONIE service discovery............................................................................................................................................. 36

9 Specications..............................................................................................................................................38

Chassis physical design................................................................................................................................................... 38

IEEE standards................................................................................................................................................................. 39

Agency compliance..........................................................................................................................................................39

Network Equipment Building Systems Compliance.....................................................................................................39

USA Federal Communications Commission Statement.............................................................................................. 40

European Union EMC Directive Conformance Statement......................................................................................... 40

Japan VCCI Compliance for Class A Equipment...........................................................................................................41

Korean Certication of Compliance................................................................................................................................41

Safety Standards and Compliance Agency Certications.......................................................................................... 42

Electromagnetic Compatibility .......................................................................................................................................42

EmissionsImmunity.....................................................................................................................................................42

Product recycling and disposal....................................................................................................................................... 43

Waste Electrical and Electronic Equipment (WEEE) Directive for Recovery, Recycle and Reuse of IT

and Telecommunications Products.......................................................................................................................... 43

10 Technical Support...................................................................................................................................... 44

Dell EMC support.............................................................................................................................................................44

Contents

About this guide

This guide provides site preparation recommendations, step-by-step procedures for rack mounting and desk mounting, inserting optional

modules, and connecting to a power source.

CAUTION: To avoid electrostatic discharge (ESD) damage, wear grounding wrist straps when handling this equipment.

WARNING: Only trained and qualied personnel can install this equipment. Read this guide before you install and power up this

equipment. This equipment contains two power cords. Disconnect both power cords before servicing.

WARNING: This equipment contains optical transceivers, which comply with the limits of Class 1 laser radiation.

Figure 1. Class 1 laser product

NOTE

: When no cable is connected, visible and invisible laser radiation may be emitted from the aperture of the optical

transceiver ports. Avoid exposure to laser radiation and do not stare into open apertures.

Related documents

For more information about the S4048–ON switch, see the following documents:

• Dell Networking S4048–Open Networking (ON) Getting Started Guide

• Dell Networking S4048–Open Networking (ON) Release Notes

• Dell Open Networking Troubleshooting Guide

NOTE

: For the most recent documentation, visit Dell EMC support: www.dell.com/support.

About this guide 5

The S4048–ON switch

The following sections describe the Dell EMC S4048–ON switch:

Topics:

• Introduction

• Features

• Physical dimensions

• Switch status

• LED display

• Prerequisites

• S4048–ON congurations

Introduction

S4048-ON is a networking switch for campus aggregation and core switching 10 Gbps servers and 40 Gbps optical uplinks to the 40 Gbps

switching fabric in the core.

The S4048–ON has:

• Forty-eight ports of 10G SFP+ ports for a 1/10 Gbps transceiver

• Six 40 Gbps xed QSFP+ optical ports for a 40 Gbps transceiver

• Serial RS 232 port, RJ-45, and MicroUSB

• RJ–45 management port

The S4048–ON I/O side includes:

• Forty-eight xed SFP+ and six xed QSFP+ ports

• Management port

• USB 2.0 port

• Serial RS 232 port, RJ-45 and MicroUSB

• LED display for the switch, fan, and power status

Figure 2. S4048–ON I/O-side view

6 The S4048–ON switch

1 SFP+ ports

2 QSFP+ ports

3 USB Type-A storage port

4 MicroUSB console port

Figure 3. S4048–ON PSU-side view

1 Power supply unit 1

2 Fan module

3 Out-of-band management port

4 Power supply unit 2

5 RS-232 serial console port

Features

The S4048–ON oers the following features:

• Forty-eight xed 1/10 Gbps SFP+ ports

• Six xed 40 Gbps QSFP+ ports for 40 Gbps transceivers

• One Micro USB serial console port

• One universal serial bus (USB) Type-A port for more le storage

• Rangeley Central processing unit (CPU) system with large memory with 2 GB DDR III RAM

• Temperature monitoring

• Software-readable thermal monitor

• Real time clock (RTC) support

• Hot-plug redundant power supply

• Power management monitoring

• Removable fans

• Standard 1U chassis

Physical dimensions

The S4048-ON has the following physical dimensions:

• 440 x 460 x 44 mm (W x D x H)

• 17.32 x 18.11 x 1.73 inches (W x D x H)

The S4048–ON switch

Switch status

You can view S4048–ON status information using the light emitting diodes (LEDs).

LED display

The S4048–ON includes LED displays on both the I/O Port and PSU side of the chassis, as shown. Some LED behaviors may change after

you install your software.

Figure 4. S4048–ON LEDs

1 SFP+ port Link and activity LEDs

2 System LEDs

3 QSFP+ port LEDs

4 FAN LED

5 Management port LEDs

6 PSU LED

The S4048–ON switch

LED behavior

The following S4048–ON switch LED behavior is seen during open networking installation environment (ONIE) operations:

Figure 5. S4048–ON LEDs

1 Master LED

2 System LED

3 Power LED

4 Fan LED

5 Locator LED

6 SFP+ link/activity LEDs

7 Stack LED

8 USB port LED

9 QSFP+ link/activity LEDs

Table 1. S4048–ON LED behavior

LED Description

System Status/Health LED

• Solid green—Normal operation

• Flashing green—Booting

• Solid amber—Critical system error

• Flashing amber—Non-critical system error, fan failure, or power

supply failure

Power LED

• O—No power

• Solid Green—Normal

• Solid amber—POST is in process

• Flashing amber—Power supply failed

MASTER LED

• O—Switch is in Stacking Slave mode

• Solid green—System is in Stacking Master or Standalone mode

The S4048–ON switch 9

LED Description

FAN LED

• Solid green—fan powered and running at the expected RPM

• Solid amber—fan failed including incompatible airow direction

when you insert the PSU or fan trays with diering airows

PSU LED

• Solid green—Normal operation

• Solid amber—Power supply critical event causing a shutdown

• Flashing amber—Power supply warning event; power continues

to operate.

LOCATOR LED

• O—Locator function is disabled

• Flashing blue—Locator function is enabled

Table 2. Management Ethernet port LEDs

LED Description

Link LED

• O—No Link

• Solid green—Link on 1 Gbps speed

• Solid yellow—Link on 10/100 Mbps speeds

Table 3. SFP+ port LEDs

LED Description

Link LED

• O—No Link

• Solid green—Link on 10 Gbps speed

• Solid amber—Link on 1 Gbp speed

Activity LED

• O—No Link

• Blinking green—Transmit/receive is active

Table 4. Default 1x40G mode QSFP+ port LEDs

LED Description

Link LED

• O—No Link

• Solid green—Link operating at maximum speed—40 Gbps

• Solid amber—Link operating at lower speed—10 Gbps

• Flashing amber—one second on and one second o—port

beacon

Activity LED

• O—No Link

• Flashing green—Link activity at maximum speed—40 Gbps

• Flashing amber—Link activity at lower speed—10 Gbps

10 The S4048–ON switch

Table 5. 4x10G mode QSFP+ port LEDs

LED Description

Link LED

• O—No Link

• Solid green—Link operating at 10 Gbps speed

• Solid amber—Link operating at lower 1 Gbps speed

Activity LED

• O—No Link

• Flashing green—Link activity at 10 Gbps speed

• Flashing amber—Link activity at 1 Gbps speed

Prerequisites

The following is a list of components required for successful installation of the S4048-ON.

NOTE: Detailed installation instructions for the S4048-ON are provided in Site Preparations and Install the S4048–ON.

• S4048–ON chassis or multiple chassis, if stacking

• AC country- and regional-specic cables to connect the AC power source to each of the chassis’ AC power supplies

• Mounting brackets for rack installation, included

• Screws for rack installation

• #1 and #2 Phillips screwdrivers, not included

• Torx screwdriver, not included

• Ground cable screws, included

• Copper/ber cables

Other optional components are:

• Ground cable

• Additional power supply unit

• Additional fan module

• Additional mounting brackets if installing in a four-post rack or cabinet

S4048–ON congurations

You can order the S4048–ON switch in several dierent congurations. You can also order optional modules and optics separately.

You can order the following supported hardware components:

• S4048–ON AC Normal Airow: 48 port 10 G RJ-45 ports with six QSFP+ 40 G ports, one AC power supply and three fan subsystems.

Airow is from the I/O-side to the PSU-side.

• S4048–ON AC Reverse Airow: 48 port 10 G RJ-45 ports with six QSFP+ 40 G ports, one AC power supply and three fan subsystems.

Airow is from the PSU-side to the I/O-side

• Fan with airow from the I/O-side to the PSU-side

• Fan with airow from the PSU-side to the I/O-side

• AC Power supply with airow from the I/O-side to the PSU-side

• AC Power supply with airow from the PSU-side to the I/O-side

The S4048–ON switch

Site preparations

The S4048–ON is suitable for installation as part of a common bond network (CBN).

You can install the switch in:

• Network telecommunication facilities

• Data centers

• Other locations where the National Electric Code (NEC) applies

For more information about S4048–ON specications, see Specications.

NOTE: Install the S4048–ON switch into a rack or cabinet before installing any optional components.

Topics:

• Site selection

• Cabinet placement

• Rack mounting

• Switch ground

• Fans and airow

• Power

• Storing components

Site selection

Install Dell EMC equipment in restricted access areas.

A restricted access area is one in which service personnel can only gain access using a special tool, lock, key or other means of security and

access is controlled by the authority responsible for the location.

Ensure that the area where you install your S4048–ON switch meets the following safety requirements:

• Near an adequate power source. Connect the switch to the appropriate branch circuit protection as dened by your local electrical

codes.

• Environmental temperature between 32° to 113°F (from 0° to 45°C).

• The switch operating ambient temperature range is from 10° to 35°C (from 50° to 95°F).

• Operating humidity is from 5 to 85 percent non-condensing.

• Storage humidity is from 5 to 95 percent non-condensing.

• In a dry, clean, well-ventilated and temperature-controlled room, away from heat sources such as hot air vents or direct sunlight.

• Away from sources of severe electromagnetic noise.

• Positioned in a rack or cabinet, or on a desktop with adequate space in the front, rear, and sides of the S4048–ON for proper

ventilation and access.

Cabinet placement

Install the S4048–ON only in indoor cabinets designed for use in a controlled environment.

Do not install the S4048–ON in outside cabinets. For cabinet placement requirements, see Site Selection.

12 Site preparations

The cabinet must meet minimum size requirements. Airow must be in accordance with the Electronic Industries Alliance (EIA) standard.

Ensure that there is a minimum of 5 inches (12.7 cm) between the intake and exhaust vents and the cabinet wall.

Rack mounting

When you prepare your equipment rack, ensure that the rack is grounded.

Ground the equipment rack to the same ground point the power service in your area uses. The ground path must be permanent.

Switch ground

Dell EMC recommends you ground you switch. Use the S4048–ON in a common bond network (CBN).

Connect the grounding cables as described in Install the S4048–ON.

Fans and airow

The S4048–ON fans support two airow options.

Fan combinations

The S4048-ON has stock keeping units (SKUs) that support the following congurations. Installation of the fans is done as part of the

factory install based on SKU type.

• AC PSU with fan airow from the I/O-side to the PSU-side

• AC PSU with fan airow from the PSU-side to the I/O-side

Be sure to order the fans suitable to support your site’s ventilation. Use a single type of airow fan in your switch. Do not mix reverse and

normal air ows in a single S4048–ON chassis.

For proper ventilation, position the S4048-ON in an equipment rack (or cabinet) with a minimum of 5 inches (12.7 cm) of clearance around

the exhaust vents. When you install two S4048-ON switches near each other, position the two chassis at least 5 inches (12.7 cm) apart to

permit proper airow. The fan speed increases when the internal temperature reaches 161.6°F (72°C) and decreases to normal speed

when the temperature falls to 136.4°F (58°C). The S4048-ON never intentionally turns o the fans.

Power

To connect the chassis to the applicable power source, use the appropriate power cord with the S4048–ON. An AC power cord is included

with the switch.

When installing AC switches, follow the requirements of the National Electrical Code, ANSI/NFPA 70 where applicable.

The switch is powered-up when the power cord is connected between the switch and the power source.

CAUTION

: Always disconnect the power cable before you service the power supply slots.

CAUTION: Use the power supply cord as the main disconnect device on the AC switch. Ensure that the socket-outlet is located/

installed near the equipment and is easily accessible.

Storing components

If you do not install your S4048–ON and components immediately, Dell EMC recommends properly storing the switch and all optional

components by following these guidelines.

• Storage location temperature must remain constant ranging from -40° to 158°F (from -40°C to 70°C).

Site preparations

• Store on a dry surface or oor, away from direct sunlight, heat, and air conditioning ducts.

• Store in a dust-free environment.

NOTE: ESD damage can occur when components are mishandled. Always wear an ESD-preventive wrist or heel ground strap

when handling the S4048–ON and its accessories. After you remove the original packaging, place the S4048–ON and its

components on an anti-static surface.

14 Site preparations

NEBS compliance

For your switch to be network equipment building system (NEBS) compliant, you must follow the instructions detailed in this section.

To be NEBS compliant, orient your switch in the rack so that the air inlet is from the front aisle and the air exhaust is to the back aisle.

Important information

WARNING: The SFP+, QSFP, QSFP28, console, Ethernet management, and universal serial bus (USB) ports are suitable for

connection to intrabuilding or unexposed wiring or cabling only. You MUST NOT metallically connect the ports to interfaces that

connect to the out side plant (OSP) or its wiring. Use these interfaces as intrabuilding interfaces only (Type-2 or Type-4 ports as

described in GR-1089-CORE, Issue 6) and they require isolation from the exposed OSP cabling. Adding primary protectors is not

sucient protection to connect these interfaces metallically to OSP wiring.

WARNING: If you install and connect the S4048-ON switch to a commercial AC power source, you must connect the switch to

an external special protection device (SPD).

To be NEBs compliant:

• Locate your switch in a restricted-access area were only trained personnel are allowed access.

• Install and connect your switch to the common bonding network (CBN).

• You can also install and connect your switch to the central oce.

• Connect the battery returns of your switch as DC-I.

• Ground your switch using a copper ground conductor.

• Clean and coat all bare grounding connection points on your switch with an antioxidant solution before making connections.

• Bring all unplated surfaces on your switch to a bright nish and treat them with an antioxidant solution before making connections.

• To ensure electrical continuity, remove any nonconductive surfaces on your switch from the threads and connection points.

• Use the two-hole, Listed, compression-type lug with an AWG 14 gauge wire for switch grounding.

NOTE

: The S4048–ON can operate at -40.5 VDC to -60 VDC at a maximum current level of 15A.

NOTE: The S4048-ON is Earthquake Z4-compliant when you attach the ReadyRails to the four-post frame using threaded

hardware. Do not use the tool-less or two-post installation methods.

NEBS compliance 15

S4048–ON installation

To install the S4048–ON switch, Dell EMC recommends completing the installation procedures in the order presented in this chapter.

Always handle the S4048–ON and its components with care. Avoid dropping the switch or its eld replaceable units (FRUs).

NOTE: ESD damage can occur if components are mishandled. Always wear an ESD-preventive wrist or heel ground strap when

handling the S4048–ON and its components. As with all electrical devices of this type, take all the necessary safety precautions

to prevent injury when installing this switch.

Topics:

• Unpack the switch

• Rack or cabinet hardware installation

• SFP+ and QSFP+ optic installation

• Switch power-up

Unpack the switch

NOTE

: Before unpacking the switch, inspect the container and immediately report any evidence of damage.

When unpacking the S4048-ON switch, make sure that the following items are included:

• One S4048-ON switch

• One RJ-45 to DB-9 female cable

• Two sets of rail kits, no tools required

• One PSU—a second PSU is sold separately

• One AC country/region-specic power cord

• S4048–ON Getting Started Guide

• Safety and Regulatory Information

• Warranty and Support Information

Unpack

1 Place the container on a clean, at surface and cut all straps securing the container.

2 Open the container or remove the container top.

3 Carefully remove the switch from the container and place it on a secure and clean surface.

4 Remove all packing material.

5 Inspect the product and accessories for damage.

Rack or cabinet hardware installation

You may either place the switch on the rack shelf or mount the switch directly into a 19" wide, EIA-310- E-compliant rack—four-post, two-

post, or threaded methods. The ReadyRails™ system is provided for one 1U front-rack and two-post installations.

The ReadyRails system includes two separately packaged rail assemblies and two rails that are shipped attached to the sides of the switch.

16 S4048–ON installation

WARNING: This is a condensed reference. Read the safety instructions in your Safety, Environmental, and Regulatory

information booklet before you begin.

NOTE: The illustrations in this document are not intended to represent a specic switch.

NOTE: Do not the use the mounted Ready-Rails as a shelf or a workplace.

Rack mount safety considerations

• Rack loading—Overloading or uneven loading of racks may result in shelf or rack failure, causing damage to the equipment and possible

personal injury. Stabilize racks in a permanent location before loading begins. Mount the components beginning at the bottom of the

rack, then work to the top. Do not exceed your rack’s load rating.

• Power considerations—Connect only to the power source specied on the unit. When multiple electrical components are installed in a

rack, ensure that the total component power ratings do not exceed the circuit capabilities. Overloaded power sources and extension

cords present re and shock hazards.

• Elevated ambient temperature—If installed in a closed rack assembly, the operating temperature of the rack environment may be

greater than the room ambient temperature. Use care not to exceed the 45°C maximum ambient temperature of the switch.

• Reduced air ow—Install the equipment in the rack so that the amount of airow required for safe operation of the equipment is not

compromised.

• Reliable earthing—Maintain reliable earthing of rack-mounted equipment. Pay particular attention to the supply connections other than

the direct connections to the branch circuit, for example: use of power strips.

• Do not mount the equipment with the rear panel facing in the downward position.

ReadyRails system installation

The ReadyRails rack mounting system is provided to easily congure your rack for installation of your S4048-ON switch.

You can install the ReadyRails system using the 1U tool-less method or one of three possible 1U tooled methods: two-post ush mount,

two-post center mount, or four-post threaded.

CAUTION

: Your switch is not NEBS Earthquake Z4-compliant if you use the 1U tool-less square-hole or two-post installation

methods.

1 With the ReadyRails ange ears facing outward, place one rail between the left and right vertical posts.

Align and seat the rear ange rail pegs in the rear vertical post ange. Item 1 and its extractions show how the pegs appear in both the

square and non-threaded round holes.

S4048–ON installation

Figure 6. 1U tool-less conguration

2 Align and seat the front ange pegs in the holes on the front side of the vertical post, item 2.

3 Repeat this procedure for the second rail.

4 To remove each rail, pull on the latch release button on each ange ear and unseat each rail, item 3.

Two-post ush-mount conguration

CAUTION

: Your switch is not NEBS Earthquake Z4-compliant if you use this installation method.

1 For this conguration, remove the latch castings from the front side of each ReadyRails assembly, item 1.

To remove the two screws from each front ange ear on the switch side of the rail and remove each casting, use a Torx screwdriver.

Retain the castings for future rack requirements. It is not necessary to remove the rear ange castings.

S4048–ON installation

Figure 7. Two-post ush-mount conguration

2 Attach one rail to the front post ange with two user-supplied screws, item 2.

3 Slide the plunger bracket forward against the vertical post and secure the plunger bracket to the post ange with two user-supplied

screws. Refer to item 3.

4 Repeat this procedure for the second rail.

Two-post center-mount conguration

CAUTION

: Your switch is not NEBS Earthquake Z4-compliant if you use this installation method.

1 Slide the plunger bracket rearward until it clicks into place and secure the bracket to the front post ange with two user-supplied

screws, item 1.

S4048–ON installation

Figure 8. Two-post center-mount conguration

2 Slide the back bracket towards the post and secure it to the post ange with two user-supplied screws, item 2.

3 Repeat this procedure for the second rail.

Four-post threaded conguration

CAUTION

: To be NEBS Earthquake Z4-compliant, you must remove the tool-less latch castings described in Step 1.

1 For this conguration, remove the latch castings from each end of the ReadyRails assemblies.

To remove the two screws from each ange ear and remove each casting, use a Torx driver, item 1. Retain the castings for future rack

requirements.

S4048–ON installation

Page is loading ...

Dell PowerSwitch S4048-ON Quick start guide

Brand: Dell

Model: PowerSwitch S4048-ON

Category: Network switches

Type: Quick start guide

Download PDF

report

Dell PowerSwitch S4048-ON Quick start guide

Dell PowerSwitch S4048-ON Quick start guide

Related papers

Other documents